United Kingdom
France
Germany
Netherlands
Sweden
USA
Italy
Spain
Stuarts Models - Machined Kits
Available
-
The Stuart 10H is a
development from the
popular 10V Engine. It is
more than capable of
'doing work' and can
easily power a small
dynamo or pump. This
small horizontal engine
offers both power when
run at high speed and
visual interest when
operated at slow
crankshaft speeds. Engine
Description: Stuart 10H
Fully Machined Kit
Specifications:Length: 6
Inches.Flywheel Diameter:
3 Inch Diameter.Bore: 3/4
Inch.Stroke: 3/4 Inch.
Contents: Cast Iron:
Boxbed, soleplate,
cylinder, valve chest
and cover, top and
bottom cylinder covers,
flywheel.Brass: Slide
valve, piston,
connecting rod,
eccentric rod, valve
operating block, glands,
crosshead, crankshaft
bearings.Steel:
Crankshaft, crankwebbs,
eccentric sheave,
crosshead pin, piston
and valve rods.Sundries:
Detailed drawings,
gaskets, cylinder
lagging, gland packing,
fixings pack.
Manufacturer: Stuarts
Models Model / Part No:
10H Machined Kits
(34-50-71196)
Availability: In Stock
£403.00
Available
-
For many years we were
asked to produce a twin
cylinder horizontal
engine, the Stuart Score
was the answer. It is
closely related to the
Stuart D10 but is
distinctive enough to be
attractive in its own
right. As with all Stuart
Models Machined Kits it
is supplied complete with
a hand numbered
certificate of
authentication. Engine
Description: Stuart Score
Fully Machined Kit
Specifications:Length: 6
Inches.Flywheel Diameter:
3 Inch Diameter.Bore: 3/4
Inch.Stroke: 3/4 Inch.
Contents:Cast Iron:
Boxbed, soleplate,
cylinders, valve chests
and covers, top and
bottom cylinder covers,
flywheel.Brass: Slide
valves, pistons,
connecting rods,
eccentric rods, valve
operating blocks,
glands, crossheads,
crankshaft
bearings.Steel:
Crankshaft, crankwebbs,
eccentric sheaves,
crosshead pins, piston
and valve rods.Sundries:
Detailed drawings,
gaskets, cylinder
lagging, gland packing,
fixings pack.
Manufacturer: Stuart
ModelsModel / Part No:
Score Machined Kits
(34-50-71217)
Availability: In Stock
£759.00
Available
-
The Twin Victoria is
essentially two Stuart
Victorias running side by
side. This makes for a
very impressive model
which will be the center
piece of any collection.
As with all Stuart Models
machined kits it is
supplied complete with a
hand numbered certificate
of authentication. Engine
Description: Stuart Twin
Victoria Fully Machined
Kit
Specifications:Length: 15
1/2 Inches.Flywheel
Diameter: 7 Inches
Diameter. Bore: 1 Inch
Diameter. Stroke: 2
Inches. Contents: Cast
Iron: Baseplates,
cranks, cylinders,
valve chests and covers,
front and rear cylinder
covers, pistons,
flywheel.Brass: Slide
valves, eccentric
straps, valve operating
blocks, glands, conrod
bushes, crossheads,
crankshaft bearingsSteel:
Crankshaft, connecting
rods, eccentric sheaves,
eccentric rods,
clevises, crankpins,
piston and valve rods,
all materials for valve
gear and crosshead
guides.Sundries: Detailed
drawings, gaskets,
viton O rings, gland
packing, fixings pack.
Manufacturer: Stuart
ModelsModel / Part No:
Twin Victoria Machined
Kits (34-50-71426)
Availability: In Stock
£1794.00
Available
-
The Stuart Victoria
follows closely the
design of low pressure
horizontal engines used
throughout the nineteenth
century, to provide
power in workshops and
factories. The large
flywheel allows the
engine to run smoothly at
low speeds where the long
elegant stroke can be
appreciated. As with all
Stuart Models machined
kits it is supplied
complete with a hand
numbered certificate of
authentication. Engine
Description: Stuart
Victoria Fully Machined
Kit. Specifications:
Length: 15 1/2
Inches.Flywheel Diameter:
7 Inches Diameter.Bore: 1
Inch Diameter.Stroke: 2
Inches. Contents:Cast
Iron: Baseplate,
pedestal, pulley,
crank, cylinder, valve
chest and cover, front
and rear cylinder covers,
piston, flywheel.Brass:
Slide valve, eccentric
strap, valve operating
block, glands, conrod
bush, crossheads,
crankshaft
bearings.Steel:
Crankshaft, connecting
rod, eccentric sheave,
eccentric rod, clevis,
crankpin, piston and
valve rods, all
materials for valve gear
and crosshead
guides.Sundries: Detailed
drawings, gaskets,
viton O ring, gland
packing, fixings pack.
Manufacturer: Stuart
ModelsModel / Part No:
Victoria Machined Kits
(34-50-71420)
Availability: In Stock
£1053.00
Available
-
The Stuart 10V has for
many years been the most
popular engine in our
range. It is powerful
enough to drive a 48 inch
model steam boat. As with
all Stuart Models
machined kits it is
supplied complete with a
hand numbered certificate
of authentication. Engine
Description: Stuart 10V
Fully Machined Kit
Specifications: Height: 6
Inches.Flywheel Dia.: 3
Inches Diameter.Bore: 3/4
Inch.Stroke: 3/4 Inch.
Contents:Cast Iron:
Boxbed, soleplate,
standard, cylinder,
valve chest and cover,
top and bottom cylinder
covers, flywheel.Brass:
Slide valve, piston,
connecting rod,
eccentric rod, valve
operating block, glands,
crosshead, crankshaft
bearings.Steel:
Crankshaft, crankwebbs,
eccentric sheave,
crosshead pin, piston
and valve rods.Sundries:
Detailed drawings,
gaskets, cylinder
lagging, gland packing,
fixings pack.
Manufacturer: Stuart
ModelsModel / Part No:
10V Machined
Kits(34-50-71185)
Availability: In Stock
£403.00
Available
-
The Stuart Half Beam is a
recent addition to our
range. Based on the
Stuart Beam this engine
is relatively slow moving
with the advantage of
only requiring a small
boiler to run. Under
steam the intricate
movement of the valve
gear combined with the
elegant rocking of the
beam make this engine
almost mesmerizing to
watch. As with all Stuart
Models machined kits it
is supplied complete with
a hand numbered
certificate of
authentication. Engine
Description: Stuart Half
Beam Fully Machined Kit.
Specifications: Width: 11
3/4 Inches.Flywheel
Diameter: 7 Inches
Diameter. Bore: 1 Inch
Diameter.Stroke: 2
Inches. Contents: Cast
Iron: Baseplate, beam,
beam support, A frames,
pedestal, pulley,
crank, cylinder, valve
chest and cover, top and
bottom cylinder covers,
piston, flywheel.Brass:
Slide valve, eccentric
strap, valve operating
block, glands, conrod
bush, beam pivot
support, crankshaft
bearings, beam support
bearings, valve gear
bearings.Steel:
Crankshaft, connecting
rod, eccentric sheave,
eccentric rod, clevis,
crankpin, piston and
valve rods, all
materials for valve gear
and beam pivot.Sundries:
Detailed drawings,
gaskets, viton O ring,
gland packing, fixings
pack. Manufacturer:
Stuart ModelsModel / Part
No: Half Beam Machined
Kits (34-50-71457)
Availability: In Stock
£1108.00
Available
-
The Stuart D10 is well
suited to all kinds of
stationary and marine
work, being able to
reach speeds of up to
2000 rpm. This model must
be seen to be fully
appreciated. It is both
elegant and well designed
in addition to being
thoroughly practical. As
with all Stuart Models
machined kits it is
supplied complete with a
hand numbered certificate
of authentication. Engine
Description: Stuart D10
Machined Kit
Specifications:Height: 6
Inches.Discwheel
Diameter: 1 5/8 inch
Diameter.Bore: 3/4 Inch.
Contents:Cast Iron:
Boxbed, soleplate,
standards, cylinders,
valve chests and covers,
top and bottom cylinder
covers, flywheel.Brass:
Slide valves, pistons,
connecting rods,
eccentric rods, valve
operating blocks,
glands, crossheads,
crankshaft
bearings.Steel:
Crankshaft, crankwebbs,
eccentric sheaves,
crosshead pins, piston
and valve rods.Sundries:
Detailed drawings,
gaskets, cylinder
lagging, gland packing,
fixings pack.
Manufacturer: Stuart
ModelsModel / Part No:
D10 Machined Kits
(34-50-71205)
Availability: In Stock
£807.50
Available
-
The James Coombes is
based on a table engine
reputed to have worked
for more than a century
at a Bristol colliery.
The original engine
developed approximately
20 horsepower at 60 psi
running at 40 r.p.m. This
model is scaled down one
inch to the foot (1:12).
As with all Stuart Models
machined Kits it is
supplied complete with a
hand numbered certificate
of authentication. Engine
Description: Stuart James
Coombes Machined Kit
Specifications:Height: 14
1/8 Inches.Flywheel
Diameter: 7 Inches
Diameter.Bore: 1 Inch
Diameter.Stroke: 2
Inches. Contents:Cast
Iron: Baseplate,
crosshead guides,
pedestal, pulley,
crank, cylinder, valve
chest and cover, top
cylinder cover, piston,
flywheel.Brass: Slide
valve, eccentric strap,
valve operating block,
glands, conrod bush,
crossheads, crankshaft
bearings.Steel:
Crankshaft, connecting
rod, eccentric sheave,
eccentric rod, clevis,
crankpin, top and bottom
plates, piston and valve
rods, all materials for
valve gear.Sundries:
Detailed drawings,
gaskets, viton O ring,
gland packing, fixings
pack. Manufacturer:
Stuart ModelsModel / Part
No: James Coombes
Machined Kits
(34-50-71408)
Availability: In Stock
£1108.00
Available
-
The Stuart S50 is an
elegant model 'Mill
Engine' of the type used
to power small factories
in the north of England
during the mid-nineteenth
century. As with all
Stuart Models machined
kits it is supplied
complete with a hand
numbered certificate of
authentication. Engine
Description: Stuart S50
Machined Kit
Specifications: Length: 8
1/2 inches.Flywheel
Diameter: 3 inches.Bore:
5/8 inch.Stroke: 1 1/4
inches. Contents:Cast
Iron: Soleplate,
cylinder, valve chest
and cover, front and
rear cylinder covers,
flywheel. Manufacturer:
Stuart ModelsModel / Part
No: S50 Machined Kits
(34-50-71316)Brass: Slide
valve, piston,
eccentric strap, valve
operating block, glands,
crosshead.Steel:
Crankshaft, crankwebb,
connecting rod,
eccentric sheave,
eccentric rod, distance
pieces, slide bars,
crankpin, piston and
valve rods.Sundries:
Detailed drawings,
gaskets, fibre washer,
cylinder lagging, gland
packing, fixings pack.
Availability: In Stock
£403.00
Available
-
The Stuart Beam is a
relatively simple engine
to construct. The use of
Watts parallel motion
makes this engine
fascinating to watch,
particularly at slow
speeds. As with all
Stuart Models machined
kits the Stuart Beam is
supplied complete with a
hand numbered certificate
of authentication. Engine
Description: Stuart Beam
Machined Kit
Specifications:Length: 13
Inches.Flywheel Diameter:
7 Inches Diameter.Bore: 1
Inch Diameter.Stroke: 2
Inches. Contents: Cast
Iron: Bedplate, column,
beam, pedestal, pulley,
crank, cylinder, valve
chest and cover, top and
bottom cylinder covers,
piston, flywheel.Brass:
Slide valve, eccentric
strap, valve opperating
block, glands, conrod
bush, crankshaft
bearings, beam bearings,
entablature bearings,
valve gear
bearings.Steel:
Crankshaft, connecting
rod, eccentric sheave,
eccentric rod, clevis,
crankpin, beam shaft,
entablatures, piston and
valve rods, valve gear
and parallel
motion.Sundries: Detailed
drawings, gaskets,
viton "O" ring,
gland packing, fixing
pack. Manufacturer:
Stuart ModelsModel / Part
No: Beam Machined Kits
(34-50-71391)
Availability: In Stock
£1108.00
Denmark