About Us
Contact Us
Privacy Policy
Cookie Usage
Add Your Store

More From Contributor

image missing
Stuart Models Iver
Steam Locomotive Ready
To Run
Models (34-50-10261)
£728.50
The Iver is the first in our range of radio controlled live steam locomotives. Originating from the well respected Cheddar Models range we have continued to use the same high quality suppliers & materials, whilst taking the opportunity to improve the overall appearance. Each model is supplied complete with a Futaba radio control system as standard. The boiler is powered by a ceramic gas burner & is fitted with a pressure gauge, water gauge & safety valve. Engine Description: Ready to Run ' Iver' Radio Controlled Steam Powered Locomotive. Specifications: Length: 11 inches.
Height: 6 inches.
Width: 4 5/16 inches. Weight: 2.65 kgs. Cylinder Bore: Twin 5/16 inch diameter. Cylinder Stroke: Twin 3/4 inch. Contents: Locomotive: Complete & ready to run Iver locomotive with ceramic gas burner, refillable gas tank, pressure gauge & syphon, water gauge, safety valve, displacement lubricator & radio control handset. Accessories: Gas refill adaptor, Gas burner, supply pipe, jet & disposable gas can valve, lubricator syringe & needle, cylinder oil, bearing oil, boiler test certificate & instructions. Manufacturer: Stuart Models Model / Part No: Iver Steam Locomotive Ready to Run Models (34-50-10261)

...
Archived Product
image missing
Stuart Models James
Coombes Machined Kits
(34-50-71408)
£1108.00
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). As with all Stuart Models machined Kits it is supplied complete with a hand numbered certificate of authentication. Engine Description: Stuart James Coombes Machined Kit Specifications:
Height: 14 1/8 Inches. Flywheel Diameter: 7 Inches Diameter. Bore: 1 Inch Diameter. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Machined Kits (34-50-71408)
...
Archived Product
image missing
Stuart Models James
Coombes Ready To Run
Models (34-50-71409)
£1722.55
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). As with all Stuart Models finished engines it is supplied ready to run complete with a hand numbered certificate of authentication. Engine Description: Stuart James Coombes Ready to Run. Specifications:

Height: 14 1/8 Inches. Flywheel: 7 Inches. Bore: 1 Inch. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Ready to Run Models (34-50-71409)

...
Archived Product
image missing
Stuart Models James
Coombes Unmachined Set
Of
Castings (34-50-71407)
£275.99
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart James Coombes Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications:
Height: 14 1/2 Inches. Flywheel Diameter: 7 Inches. Cylinder Bore: 1 Inch Diameter. Cylinder Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Unmachined Set of Castings (34-50-71407)
...
Archived Product
image missing
Stuart Models Major
Beam Unmachined Set Of
Castings (34-50-71414)
£945.85
The Stuart Major Beam is typical of the smaller industrial engines of the nineteenth century. It is based on a eighth scale model designed by Mr. George Gentry & serialised in Model Engineer magazine throughout 1914. In 1968 modifications were made to the engine by Mr. H. A. Taylor including a reduction in the bore, a redesigned feed pump & replacement of Whitworth fixings with B.A. The Stuart Major Beam kit

Includes:: all the castings, finished gears, piston rings & drawings but none of the necessary materials or fixings. Engine Description: Stuart Major Beam Set of Unmachined Castings, Governor Gears, Piston Rings & Drawings only. Specifications:

Height: 18 1/4 Inches. Flywheel Diameter:13 7/8 Inches. Cylider Bore: 1 3/4 Inches Diameter. Cylinder Stroke:3 3/4 Inches. Contents: Cast Iron: Baseplate, pedestal, column, beam, pulley, entablature, cylinder, valve chest & cover, top cylinder cover, cylinder boss, piston, slide valve, crank, main bearings, beam bearings, connecting rod, feed pump body, feed pump gl&, governor bracket, flywheel. Gunmetal: Valve shaft bearings, feed pump flange, eccentric strap. Sundries: Seven detailed drawings, piston rings, finished governor gears.



...
Archived Product
image missing
Stuart Models No.4
Unmachined Set Of
Castings (34-50-71156)
£354.85
The Stuart No. 4 is a most impressive engine. When fitted with a discwheel this engine is capable of running at very high speeds making it especially suited to driving a dynamo. A reverse gear is available which can be added to the basic engine if required. Both the engine & reverse gear are supplied as complete sets of castings together with all the materials, fixings & drawings included. Engine Description: Stuart No.4 Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications:
Height: 10 Inches. Flywheel Diameter: 5 Inches. Cylinder Bore: 1 1/2 Inches. Cylinder Stroke: 1 1/2 Inches. Contents: Cast Iron: Boxbed, soleplate, standard, cylinder, valve chest & cover, top & bottom cylinder covers, piston, eccentric sheave, 5 in. flywheel. Gunmetal: Slide valve, eccentric strap, connecting rod, valve operating block, glands, crosshead, crankshaft bearings. Steel: Crankshaft, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, cylinder lagging, gasket material, piston rings, gland packing, fixings pack.
...
Archived Product
image missing
Stuart Models No.8
Unmachined Set Of
Castings (34-50-71175)
£233.75
The Stuart No.8 shares many common parts with the Stuart 7A, it is a relatively simple engine to build requiring only a 3 1/2 in. lathe. This model is supplied as a complete set of castings, materials, fixings & drawings. In general full sized horizontal engines were not arranged to reverse, this is why we do not offer reverse gears for our horizontal engines. Engine Description: Stuart No.8 Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications: Length: 8 1/2 Inches. Flywheel Diameter: 3 1/2 Inches. Cylinder Bore: 1 Inch Diameter. Cylinder Stroke: 1 Inch. Contents: Cast Iron: Boxbed, soleplate, cylinder, valve chest & cover, front & rear cylinder covers, piston, eccentric sheave, 3 9/16 in. flywheel. Gunmetal: Slide valve, eccentric strap, connecting rod, valve operating block, glands, crosshead, crankshaft bearings. Steel: Crankshaft, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, cylinder lagging, gasket material, gland packing, “O”?ring, fixings pack. ...
Archived Product
image missing
Stuart Models No.9
Unmachined Set Of
Castings (34-50-71178)
£354.85
The Stuart No.9 is regarded by many as the most attractive engine in the Stuart range. The No.9 is typical of the large powerful Steam Engines installed in factories & mills to provide power. As a steaming model or a static display the Stuart No.9 is a fine example of model engineering. Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart No.9 Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications: Length: 11 Inches. Flywheel Diameter: 5 Inches. Cylinder Bore: 1 1/2 Inches. Cylinder Stroke: 1 1/2 Inches. Contents: Cast Iron: Boxbed, soleplate, cylinder, valve chest & cover, front & rear cylinder covers, piston, connecting rod, flywheel. Gunmetal: Slide valve, eccentric strap, connecting rod bearings, valve operating block, glands, crosshead, valve rod guide, crankshaft bearings. Steel: Crankshaft, eccentric sheave, piston & valve rods, eccentric rod, all materials for valve gear. Sundries: Detailed drawings, cylinder lagging, gaskets, piston rings, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: No.9 Unmachined Set of Castings (34-50-71178) ...
Archived Product
image missing
Stuart Models Oil
Field Pump Unmachined
Set Of
Castings (34-50-71199)
£275.99
The Oil Field Pump is a relatively new addition to the Stuart range. We have designed the model so it can be powered by any of our engines & closely follows the style of oil field pumps working to this day all over the world. The reciprocating action of this model, when driven by an engine, makes for a fascinating centre piece to any steam display. The Oil Field Pump is supplied as a complete set of castings & materials together with precut gears, drawings, fixings & fittings. Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart Oil Field Pump set of Unmachined Castings, Materials, Fixings Pre cut Gears & Drawings Specifications:
Height: 12 Inches. Length: 10 Inches.
Width: 4 1/2 Inches. Flywheel Diameter: 2 1/2 Inches. Contents: Cast Iron: Baseplate, control weights, control arms, pump head, flywheel. Gunmetal: Arm block, front support legs, pump base, lower pump body, upper pump body, pipe unions, journal blocks. Steel: Spindles, support columns, screws, bracket, bearing block caps, beam, stoke & piston slides. Sundries: Detailed drawings, viton ?O? rings, washers, balls, finished gears, fixings pack. Manufacturer: Stuart Models Model / Part No: Oil Field Pump Unmachined Set of Castings (34-50-71199)

...
Archived Product
image missing
Stuart Models Pillar
Drill Unmachined Set
Of
Castings (34-50-74020)
£171.99
The Pillar Drill has a rising table operated by a rack & pinion mechanism, in the same way as full sized machines of the period were operated. A choice of running speeds can be selected by utilising the stepped pulley. The Stuart Pillar Drill comes complete with pre cut gears, making machining considerably easier. Engine Description: Stuart Pillar Drill Set of Castings, Materials, Fixings, Pre cut gears & Drawings. Specifications:

Height: 9 Inches.
Width: 5 Inches.
Depth: 3 Inches. Contents: Cast Iron: Base, table bracket, head, pulleys. Brass: Bushes. Steel: Collars, column, table, spindles, pulleys, shafts, handles, lever, spacer, handwheel & finished gears. Sundries: Detailed Drawings & Fixings. Manufacturer: Stuart Models Model / Part No: Pillar Drill Unmachined Set of Castings (34-50-74020)



...
Archived Product

Stuart Models No.1 Unmachined Set Of Castings (34-50-71151)

The first Stuart No.1 was built by Mr. Stuart Turner over one hundred years ago. It is a classic design, and so beautifully proportioned, that it makes the perfect display model. This engine is quite capable of hard work producing 1/2 bhp at 800 rpm. For marine installations we are able to offer a reverse gear and discwheel. Please remember our sets of castings require the use of a lathe and milling machine to turn them into a working steam engine. Engine Description: Stuart No.1 Set of Unmachined Castings, Materials, Fixings and Drawings. Specifications:Height: 13 Inches.Flywheel Diameter: 7 Inches.Cylinder Bore: 2 Inches.Cylinder Stroke: 2 Inches. Contents:Cast Iron: Boxbed, soleplate, standard, cylinder, valve chest and cover, top and bottom cylinder covers, piston, eccentric
sheave, flywheel.Gunmetal: Slide valve, eccentric strap, valve operating block, glands, valve spindle guide, crankshaft bearings.Steel: Crankshaft, connecting rod, eccentric rod, column, crosshead guide plates, crankpin, piston and valve rods, all materials for valve gear.Sundries: Detailed drawings, cylinder lagging, gaskets, piston rings, gland packing, fixings pack. Manufacturer: Stuart ModelsModel / Part No: No.1 Unmachined Set of Castings (34-50-71151)
RIP - This product is no longer available on our network. It was last seen on 10.03.2012

This page now acts as a permanent archive for this product. Add more information using the comments box below to ensure it can still be found by future generations.

Use our search facility to see if it is available from an alternative contributor.
Availability: In Stock
£468.75
creative toys Creative Toys
Description Reviews / Comments Add New

Product Description

The first Stuart No.1 was built by Mr. Stuart Turner over one hundred years ago. It is a classic design, & so beautifully proportioned, that it makes the perfect display model. This engine is quite capable of hard work producing 1/2 bhp at 800 rpm. For marine installations we are able to offer a reverse gear & discwheel. Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart No.1 Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications:
Height: 13 Inches. Flywheel Diameter: 7 Inches. Cylinder Bore: 2 Inches. Cylinder Stroke: 2 Inches. Contents: Cast Iron: Boxbed, soleplate, standard, cylinder, valve chest & cover, top & bottom cylinder covers, piston, eccentric sheave, flywheel. Gunmetal: Slide valve, eccentric strap, valve operating block, glands, valve spindle guide, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric rod, column, crosshead guide plates, crankpin, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, cylinder lagging, gaskets, piston rings, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: No.1 Unmachined Set of Castings (34-50-71151)

Reviews/Comments

Add New

Intelligent Comparison

Oooops!
We couldn't find anything!
Perhaps this product's unique.... Or perhaps we are still looking for comparisons!
Click to bump this page and we'll hurry up.

Price History

Oooops!
We couldn't find any historical pricing!

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

Diameter - A measurement across a circle passing through the middle
Engine - A machine designed to convert fuel into motion
Steel - An alloy made predominately of Iron combined with <2% carbon
iron - An electrical deviced used for removing creases from fabrics
iron - A chemical element (FE). The most common element on earth
Steam - Steam - water in gas form, water vapour. Commonly seen coming from a kettle
RPM - Revolutionss per minute, the number of rotations per minute around a fixed axel.
Set - a group of items usually related to one another. Some objects cannot function without the complete set of items.
Bearings - A direction or a way someone moves around.
Gunmetal - A dark grey colour, or can also be related to a corrosion resistant bronze.
Valve - An opening and closing to control the movement of fluid through pipes.
Design - A drawing or styles that shows the look and functionality of something before its made.
Classic - Something that is still like it was originally a high quality standard.
Fixings - An action of sticking an item to another surface.
Model - A representation of a person or thing, usually smaller scale. It can also be a person that wears clothing.

Supplier Information

My Hobby Store
MyHobbyStore publishes some of the most well known specialist hobby magasines in the UK and are responsible for some of the most loved events on model hobbies and woodworking. MyHobbyStore are passionate about specialist hobby needs which is why they supply a wide range of hobby supplies at the best prices.

A huge range including:
Model Boat Kits
Model Aircraft kits
Model Cars
Engineering Kits.

The range of kits they supply is very diverse including static models, petrol powered, electric and steam.

Delivery is around 7 days.
Page Updated: 2012-02-04 02:03:29

Community Generated Product Tags

Stuart no 1 unmachined (1 person tagged the product this way)
Menu