- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

Independent high-gain internally frequency compensated op-amps specifically intended to operate from a single power supply over a wide range of voltages. Application areas include transducer amplifiers DC gain blocks & all conventional op-amp circuits which are designed for single power supply systems. The device will work from standard 5V rails found in digital systems & provide the required interface electronics. in addition the device features a large DC voltage gain 100d B 1 M Hz unity gain bandwidth 120d B channel separation & class AB outputs with virtually no crossover distortion. The device will operate from a 3 to 32 Vdc rail or from a dual plusmn 1.5V to plusmn 16 Vdc supply. ...

This IC in a TO92 package is a 3-terminal adjustable current source with a 10000 to 1 range in operating current excellent current regulation & a wide dynamic voltage regulation of 1V to 40V. Current is established with one resistor connected between pins 1 R & 3 -V & no other parts are required. The current is equal to 0.0677V divided by the resistor in ohms i.e. for 1m A R 68andohm at 25C. Currents may be set in the range 1andmicro A to 10m A & regulation is 0.02 per volt. Initial current accuracy is andplusmn 3 typical. Reverse voltages of up to 20V will draw only a few microamps allowing the device to act as a rectifier & current source in AC applications. The current is also directly proportional to the temperature at the rate 0.33 per C. Zero drift operation can be obtained by adding one resistor & one diode. Applications include bias networks surge protection low power reference ramp generation LED driver & temperature sensing. ...

An adjustable 3-terminal negative voltage regulator capable of supplying 1.5A over a range of 1.2V to 37V. It is exceptionally easy to use & requires only two external resistors to set the output voltage. Besides having a higher performance compared with fixed regulators the LM337 offers full overload protection with current limiting thermal overload protection & safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected. The adjustment terminal can be bypassed with a capacitor to ground to achieve very high ripple rejection ratios that are difficult to achieve with standard 3-terminal regulators. Output voltage is set by connecting a twin resistor divider between output & circuit ground & connecting the adjustment pin to the junction. A precision current regulator can also be made by connecting a fixed resistor only between the adjustment & output pins & connecting the load to the adjustment pin. The device is available in TO220 package LM337T. Specifications Output voltage 1.2V to 37 V Inputoutput differential voltage 40V max. Operating junction temperature 25 C to 125 CLine regulation 0.01 V Load regulation 0.1 Adjustment pin current 50micro A Reference voltage 1.25V typical Output noise 0.003 of Vout Ripple rejection ratio 65d B Long term stability 0.3 125 C ...

Four independent precision voltage comparators with a typical input offset voltage of 2m V & designed to operate from a single power supply. The input common-mode voltage range

Includes:: ground even though operated from a single power supply voltage. Identical to the 3302 but offering enhanced supply voltage range & voltage gain typically 200. Designed to directly interface with TTL & CMOS & when used with a
- supply will directly interface with MOS logic where the low power drain of the LM339 is a distinct advantage over standard comparators.


...

A low power quad version of the 741 op-amp featuring high gain & internal compensation with a total supply current requirement for the IC that is less than a single conventional 741. Each op-amp has a class AB output stage & so has virtually no crossover distortion. Additional features include a low input offset voltage 1m V low input offset current typically 4n A low input bias current typically 30n A & a unity gain bandwidth of 1 M Hz. Channel separation is 120d B with a maximum operating voltage of plusmn 18 Vdc. ...

A precision integrated circuit with an output voltage that is linearly proportional to the Centigrade temperature. The advantage over the LM335Z is that it is not necessary to subtract a large constant voltage from the output to obtain the Centigrade scale. The chip does not require any external calibration to achieve accuracies of plusmn 410 deg C at room temperature & plusmn 810deg C over full temperature range. The device draws only 56micro A from voltage supplies in the range 4V to 30V so it has very low self-heating lt 0.1deg C in still air. The LM35DZ oerates in the range 0 C to 100 C. Specifications Oerating range 0deg C to 100deg C plusmn 0.9deg C Non-linearity 0.2deg C Sensor slope 10m Vdeg C Load regulation 0.4m Vm A Line regulation 0.01m Vm A Quiescent current 56micro A at VS 5V56.2micro A at VS 30 V Temperature co-efficient ofquiescent current 0.39micro Adeg C Output impedance 0.1micro with 1m A load ...