A voltage comparator that has input currents more than a hundred times lower than the 710. It will operate on andplusmn 14V or 5V supplies & will drive RTL DTL TTL MOS & switch voltages up to 40V at currents as high as 50m A. Both input & output can be isolated from system ground & the output can drive loads referred to ground positive or negative. Offset balancing & strobe capability are provided. ...

- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

- Output adjustable between 1.25V & 37V
- Internal thermal overload protection
- Internal short circuit current limiting


...

Independent high-gain internally frequency compensated op-amps specifically intended to operate from a single power supply over a wide range of voltages. Application areas include transducer amplifiers DC gain blocks & all conventional op-amp circuits which are designed for single power supply systems. The device will work from standard 5V rails found in digital systems & provide the required interface electronics. in addition the device features a large DC voltage gain 100d B 1 M Hz unity gain bandwidth 120d B channel separation & class AB outputs with virtually no crossover distortion. The device will operate from a 3 to 32 Vdc rail or from a dual plusmn 1.5V to plusmn 16 Vdc supply. ...

An easily calibrated precision temperature sensor whose operation is similar to a zener diode. The device has a breakdown voltage directly proportional to absolute temperature & has a linear output equal to 10m VC. The device operates over a current range of 400andmicro A to 5m A 1m A recommended & even when uncalibrated has a typical temperature error of only 2C over its operating range. When calibrated the error is 1C. ...

An adjustable 3-terminal negative voltage regulator capable of supplying 1.5A over a range of 1.2V to 37V. It is exceptionally easy to use & requires only two external resistors to set the output voltage. Besides having a higher performance compared with fixed regulators the LM337 offers full overload protection with current limiting thermal overload protection & safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected. The adjustment terminal can be bypassed with a capacitor to ground to achieve very high ripple rejection ratios that are difficult to achieve with standard 3-terminal regulators. Output voltage is set by connecting a twin resistor divider between output & circuit ground & connecting the adjustment pin to the junction. A precision current regulator can also be made by connecting a fixed resistor only between the adjustment & output pins & connecting the load to the adjustment pin. The device is available in TO220 package LM337T. Specifications Output voltage 1.2V to 37 V Inputoutput differential voltage 40V max. Operating junction temperature 25 C to 125 CLine regulation 0.01 V Load regulation 0.1 Adjustment pin current 50micro A Reference voltage 1.25V typical Output noise 0.003 of Vout Ripple rejection ratio 65d B Long term stability 0.3 125 C ...

Four independent precision voltage comparators with a typical input offset voltage of 2m V & designed to operate from a single power supply. The input common-mode voltage range

Includes:: ground even though operated from a single power supply voltage. Identical to the 3302 but offering enhanced supply voltage range & voltage gain typically 200. Designed to directly interface with TTL & CMOS & when used with a
- supply will directly interface with MOS logic where the low power drain of the LM339 is a distinct advantage over standard comparators.


...

A low power quad version of the 741 op-amp featuring high gain & internal compensation with a total supply current requirement for the IC that is less than a single conventional 741. Each op-amp has a class AB output stage & so has virtually no crossover distortion. Additional features include a low input offset voltage 1m V low input offset current typically 4n A low input bias current typically 30n A & a unity gain bandwidth of 1 M Hz. Channel separation is 120d B with a maximum operating voltage of plusmn 18 Vdc. ...

A precision integrated circuit with an output voltage that is linearly proportional to the Centigrade temperature. The advantage over the LM335Z is that it is not necessary to subtract a large constant voltage from the output to obtain the Centigrade scale. The chip does not require any external calibration to achieve accuracies of plusmn 410 deg C at room temperature & plusmn 810deg C over full temperature range. The device draws only 56micro A from voltage supplies in the range 4V to 30V so it has very low self-heating lt 0.1deg C in still air. The LM35DZ oerates in the range 0 C to 100 C. Specifications Oerating range 0deg C to 100deg C plusmn 0.9deg C Non-linearity 0.2deg C Sensor slope 10m Vdeg C Load regulation 0.4m Vm A Line regulation 0.01m Vm A Quiescent current 56micro A at VS 5V56.2micro A at VS 30 V Temperature co-efficient ofquiescent current 0.39micro Adeg C Output impedance 0.1micro with 1m A load ...