More From Contributor

£3.91
Wide range of colours
- Small bottle size ideal for small craft or hobby projects
- Available in the UK, Irel&, New Zealand

...
Archived Product
£7.81
For use with powdered chalk for marking between two points to give a straight line. Braided line resists fraying & is also useful for a plumb line as it does not spin round as a conventional twisted cord. Braided nylon has less stretch than other lines & is also the strongest. 100 metre spool. ...
Archived Product
£38.26
Hand reamers have a square on the end of the shank which allows placement into a wrench which the user rotates by h&. Used for opening out & finishing existing holes to H7 tolerance in most ferrous & non-ferrous metals. Flute Geometry
- 7° Helix Left hand spiral. To obtain the best results when using reamers it is essential to make them work. It is a common fault to prepare holes for reaming with too little stock left in. If insufficient stock is left in the hole before reaming then the reamer will rub quickly, show wear & will result in loss of diameter. It is equally important for performance not to leave too much stock in the hole.
...
Archived Product
£23.68
Hand reamers have a square on the end of the shank which allows placement into a wrench which the user rotates by h&. Used for opening out & finishing existing holes to H7 tolerance in most ferrous & non-ferrous metals. Flute Geometry
- 7° Helix Left hand spiral. To obtain the best results when using reamers it is essential to make them work. It is a common fault to prepare holes for reaming with too little stock left in. If insufficient stock is left in the hole before reaming then the reamer will rub quickly, show wear & will result in loss of diameter. It is equally important for performance not to leave too much stock in the hole.
...
Archived Product
£23.89
Hand reamers have a square on the end of the shank which allows placement into a wrench which the user rotates by h&. Used for opening out & finishing existing holes to H7 tolerance in most ferrous & non-ferrous metals. Flute Geometry
- 7° Helix Left hand spiral. To obtain the best results when using reamers it is essential to make them work. It is a common fault to prepare holes for reaming with too little stock left in. If insufficient stock is left in the hole before reaming then the reamer will rub quickly, show wear & will result in loss of diameter. It is equally important for performance not to leave too much stock in the hole.
...
Archived Product
£56.08
Dormer morse taper shank machine reamer
- Spiral flute. Used for opening out & finishing existing holes to H7 tolerance in most
...
Archived Product
£3.90
Wide range of colours
- Small bottle size ideal for small craft or hobby projects
- Available in the UK, Irel&, New Zealand

...
Archived Product

B100 HSS Hand Reamer Spiral Flute 10.00mm

Hand reamers have a square on the end of the shank which allows placement into a wrench which the user rotates by hand. Used for opening out and finishing existing holes to H7 tolerance in most ferrous and non-ferrous metals. Flute Geometry - 7° Helix Left hand spiral. To obtain the best results when using reamers it is essential to make them work. It is a common fault to prepare holes for reaming with too little stock left in. If insufficient stock is left in the hole before reaming then the reamer will rub quickly, show wear and will result in loss of diameter. It is equally important for performance not to leave too much stock in the hole.
RIP - This product is no longer available on our network. It was last seen on 03.07.2013

This page now acts as a permanent archive for this product. Add more information using the comments box below to ensure it can still be found by future generations.

Use our search facility to see if it is available from an alternative contributor.
Availability: In Stock
£33.56

Product Description

Hand reamers have a square on the end of the shank which allows placement into a wrench which the user rotates by h&. Used for opening out & finishing existing holes to H7 tolerance in most ferrous & non-ferrous metals. Flute Geometry
- 7° Helix Left hand spiral. To obtain the best results when using reamers it is essential to make them work. It is a common fault to prepare holes for reaming with too little stock left in. If insufficient stock is left in the hole before reaming then the reamer will rub quickly, show wear & will result in loss of diameter. It is equally important for performance not to leave too much stock in the hole.

Reviews/Comments

Add New

Intelligent Comparison

Oooops!
We couldn't find anything!
Perhaps this product's unique.... Or perhaps we are still looking for comparisons!
Click to bump this page and we'll hurry up.

Price History

Oooops!
We couldn't find any historical pricing!

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

Diameter - A measurement across a circle passing through the middle
Hand - A part of the body at the end of the arm
Hand - A pointer which indicates time on a clock face
Flute - A long silver instrument with buttons to press to make different notes.
Rotates - Something that can move around and axis or in a circle.
Performance - When someone is presenting a form of entertainment, also how well someone is doing within a role.

Supplier Information

Page Updated: 2012-12-03 20:01:27

Community Generated Product Tags

Oh No! The productWIKI community hasn't generated any tags for this product yet!
Menu