About Us
Contact Us
Privacy Policy
Cookie Usage
Add Your Store

More From Contributor

image missing
Stuart Models D10
Ready To Run Models
(34-50-71209)
£1108.00
The Stuart D10 is well suited to all kinds of stationary & marine work, being able to reach speeds of up to 2000 rpm. This model must be seen to be fully appreciated. It is both elegant & well designed in addition to being thoroughly practical. As with all Stuart Models finished engines it is supplied ready to run complete with a hand numbered certificate of authentication. Engine Description: Stuart D10 Ready to Run Engine. Specifications:
Height: 6 Inches. Discwheel: 1 5/8 Inch Diameter. Bore: 3/4 Inch. Stroke: 3/4 Inch. Contents: Cast Iron: Boxbed, soleplate, standards, cylinders, valve chests & covers, top & bottom cylinder covers, flywheel. Brass: Slide valves, pistons, connecting rods, eccentric rods, valve operating blocks, glands, crossheads, crankshaft bearings. Steel: Crankshaft, crankwebbs, eccentric sheaves, crosshead pins, piston & valve rods. Sundries: Detailed drawings, gaskets, cylinder lagging, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: D10 Ready to Run Models (34-50-71209)
...
Archived Product
image missing
Stuart Models D10
Unmachined Set Of
Castings (34-50-71204)
£171.99
The Stuart D10 is well suited to all kinds of stationary & marine work, being able to reach speeds of up to 2000 rpm. This model must be seen to be fully appreciated. It is both elegant & well designed in addition to being thoroughly practical. To assist the beginner the book ? Building a Vertical Steam Engine. is available. It describes in detail the machining of all the components, & is full of advice for the more challenging operations. Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart D10 Set of Unmachined Castings, Materials, Fixings & Drawings Specifications:

Height: 6 Inches. Flywheel Diameter: 3 Inches Diameter. Bore: 3/4 Inch Diameter. Stroke: 3/4 Inch. Contents: Cast Iron: Boxbed, soleplate, standards, cylinders, valve chests & covers, top & bottom cylinder covers, flywheel. Brass: Slide valves, pistons, connecting rods, eccentric rods, valve operating blocks, glands, crossheads, crankshaft bearings. Steel: Crankshaft, crankwebbs, eccentric sheaves, crosshead pins, piston & valve rods. Sundries: Detailed drawings, gaskets, cylinder lagging, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: D10 Unmachined Set of Castings (34-50-71204)

...
Archived Product
image missing
Stuart Models
Engineering Lathe
Unmachined Set
Of Castings
(34-50-74010)
£171.99
The Stuart Engineering Lathe has been carefully designed by taking the most interesting elements from lathes in use at the end of the 19th century & combining them to produce an attractive model. Please remember that whilst the gears are provided pre cut, to aid the building of this model, access to a lathe & milling machine is necessary to build this model from a set of castings. Engine Description: Stuart Engineering Lathe set of castings materials, finished gears, fixings & drawings. Specifications: Length: 8 1/2 inches.
Height: 5 inches.
Width: 3 3/4 inches. Contents: Cast Iron: Bed, tailstock end base, head stock end base, head stock, pulley. Brass: Bushes. Steel: Spindles, spindle nuts, face plate, four jaw chuck assembly, tool post assembly, cross slide assembly, tail stock assembly, rolling centre, handles handwheels. Sundries: Detailed drawings, fixings pack, finished gears.

...
Archived Product
image missing
Stuart Models Half
Beam Machined Kits
(34-50-71457)
£1108.00
The Stuart Half Beam is a recent addition to our range. Based on the Stuart Beam this engine is relatively slow moving with the advantage of only requiring a small boiler to run. Under steam the intricate movement of the valve gear combined with the elegant rocking of the beam make this engine almost mesmerizing to watch. As with all Stuart Models machined kits it is supplied complete with a hand numbered certificate of authentication. Engine Description: Stuart Half Beam Fully Machined Kit. Specifications:

Width: 11 3/4 Inches. Flywheel Diameter: 7 Inches Diameter. Bore: 1 Inch Diameter. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, beam, beam support, A frames, pedestal, pulley, crank, cylinder, valve chest & cover, top & bottom cylinder covers, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, beam pivot support, crankshaft bearings, beam support bearings, valve gear bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, piston & valve rods, all materials for valve gear & beam pivot. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: Half Beam Machined Kits (34-50-71457)

...
Archived Product
image missing
Stuart Models Half
Beam Ready To Run
Models (34-50-71458)
£1722.55
The Stuart Half Beam is a recent addition to our range. Based on the Stuart Beam this engine is relatively slow moving with the advantage of only requiring a small boiler to run. Under steam the intricate movement of the valve gear combined with the elegant rocking of the beam make this engine almost mesmerizing to watch. As with all Stuart Models finished engines it is supplied ready to run complete with a hand numbered certificate of authentication. Engine Description: Stuart Half Beam Rady to Run Engine. Specifications:
Width: 11 3/4 Inches. Flywheel: 7 Inch Diameter. Bore: 1 Inch. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, beam, beam support, ?A? frames, pedestal, pulley, crank, cylinder, valve chest & cover, top & bottom cylinder covers, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, beam pivot support, crankshaft bearings, beam support bearings, valve gear bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, piston & valve rods, all materials for valve gear & beam pivot. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: Half Beam Ready to Run Models (34-50-71458)
...
Archived Product
image missing
Stuart Models Iver
Steam Locomotive Ready
To Run
Models (34-50-10261)
£728.50
The Iver is the first in our range of radio controlled live steam locomotives. Originating from the well respected Cheddar Models range we have continued to use the same high quality suppliers & materials, whilst taking the opportunity to improve the overall appearance. Each model is supplied complete with a Futaba radio control system as standard. The boiler is powered by a ceramic gas burner & is fitted with a pressure gauge, water gauge & safety valve. Engine Description: Ready to Run ' Iver' Radio Controlled Steam Powered Locomotive. Specifications: Length: 11 inches.
Height: 6 inches.
Width: 4 5/16 inches. Weight: 2.65 kgs. Cylinder Bore: Twin 5/16 inch diameter. Cylinder Stroke: Twin 3/4 inch. Contents: Locomotive: Complete & ready to run Iver locomotive with ceramic gas burner, refillable gas tank, pressure gauge & syphon, water gauge, safety valve, displacement lubricator & radio control handset. Accessories: Gas refill adaptor, Gas burner, supply pipe, jet & disposable gas can valve, lubricator syringe & needle, cylinder oil, bearing oil, boiler test certificate & instructions. Manufacturer: Stuart Models Model / Part No: Iver Steam Locomotive Ready to Run Models (34-50-10261)

...
Archived Product
image missing
Stuart Models James
Coombes Machined Kits
(34-50-71408)
£1108.00
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). As with all Stuart Models machined Kits it is supplied complete with a hand numbered certificate of authentication. Engine Description: Stuart James Coombes Machined Kit Specifications:
Height: 14 1/8 Inches. Flywheel Diameter: 7 Inches Diameter. Bore: 1 Inch Diameter. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Machined Kits (34-50-71408)
...
Archived Product
image missing
Stuart Models James
Coombes Ready To Run
Models (34-50-71409)
£1722.55
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). As with all Stuart Models finished engines it is supplied ready to run complete with a hand numbered certificate of authentication. Engine Description: Stuart James Coombes Ready to Run. Specifications:

Height: 14 1/8 Inches. Flywheel: 7 Inches. Bore: 1 Inch. Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Ready to Run Models (34-50-71409)

...
Archived Product
image missing
Stuart Models James
Coombes Unmachined Set
Of
Castings (34-50-71407)
£275.99
The James Coombes is based on a table engine reputed to have worked for more than a century at a Bristol colliery. The original engine developed Approx. 20 horsepower at 60 psi running at 40 r.p.m. This model is scaled down one inch to the foot (1:12). Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart James Coombes Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications:
Height: 14 1/2 Inches. Flywheel Diameter: 7 Inches. Cylinder Bore: 1 Inch Diameter. Cylinder Stroke: 2 Inches. Contents: Cast Iron: Baseplate, crosshead guides, pedestal, pulley, crank, cylinder, valve chest & cover, top cylinder cover, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, crossheads, crankshaft bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, top & bottom plates, piston & valve rods, all materials for valve gear. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: James Coombes Unmachined Set of Castings (34-50-71407)
...
Archived Product
image missing
Stuart Models Major
Beam Unmachined Set Of
Castings (34-50-71414)
£945.85
The Stuart Major Beam is typical of the smaller industrial engines of the nineteenth century. It is based on a eighth scale model designed by Mr. George Gentry & serialised in Model Engineer magazine throughout 1914. In 1968 modifications were made to the engine by Mr. H. A. Taylor including a reduction in the bore, a redesigned feed pump & replacement of Whitworth fixings with B.A. The Stuart Major Beam kit

Includes:: all the castings, finished gears, piston rings & drawings but none of the necessary materials or fixings. Engine Description: Stuart Major Beam Set of Unmachined Castings, Governor Gears, Piston Rings & Drawings only. Specifications:

Height: 18 1/4 Inches. Flywheel Diameter:13 7/8 Inches. Cylider Bore: 1 3/4 Inches Diameter. Cylinder Stroke:3 3/4 Inches. Contents: Cast Iron: Baseplate, pedestal, column, beam, pulley, entablature, cylinder, valve chest & cover, top cylinder cover, cylinder boss, piston, slide valve, crank, main bearings, beam bearings, connecting rod, feed pump body, feed pump gl&, governor bracket, flywheel. Gunmetal: Valve shaft bearings, feed pump flange, eccentric strap. Sundries: Seven detailed drawings, piston rings, finished governor gears.



...
Archived Product

Stuart Models Half Beam Unmachined Set Of Castings (34-50-71456)

The Stuart Half Beam is a recent addition to our range. Based on the Stuart Beam this engine is relatively slow moving with the advantage of only requiring a small boiler to run. Under steam the intricate movement of the valve gear combined with the elegant rocking of the beam make this engine almost mesmerizing to watch. Please remember our sets of castings require the use of a lathe and milling machine to turn them into a working steam engine. Engine Description: Stuart Half Beam Engine Set of Unmachined Castings, Materials, Fixings and Drawings. Specifications:Length: 11 3/4 Inches.Flywheel Diameter.: 7 Inches.Cylinder Bore: 1 Inch Diameter.Cylinder Stroke: 2 Inches. Contents:Cast Iron: Baseplate, beam, beam support, A frames, pedestal, pulley, crank, cylinder, valve chest and
cover, top and bottom cylinder covers, piston, flywheel.Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, beam pivot support, crankshaft bearings, beam support bearings, valve gear bearings.Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, piston and valve rods, all materials for valve gear and beam pivot.Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart ModelsModel / Part No: Half Beam Unmachined Set of Castings (34-50-71456)
RIP - This product is no longer available on our network. It was last seen on 10.03.2012

This page now acts as a permanent archive for this product. Add more information using the comments box below to ensure it can still be found by future generations.

Use our search facility to see if it is available from an alternative contributor.
Availability: In Stock
£275.99
creative toys Creative Toys
Description Reviews / Comments Add New

Product Description

The Stuart Half Beam is a recent addition to our range. Based on the Stuart Beam this engine is relatively slow moving with the advantage of only requiring a small boiler to run. Under steam the intricate movement of the valve gear combined with the elegant rocking of the beam make this engine almost mesmerizing to watch. Please remember our sets of castings require the use of a lathe & milling machine to turn them into a working steam engine. Engine Description: Stuart Half Beam Engine Set of Unmachined Castings, Materials, Fixings & Drawings. Specifications: Length: 11 3/4 Inches. Flywheel Diameter.: 7 Inches. Cylinder Bore: 1 Inch Diameter. Cylinder Stroke: 2 Inches. Contents: Cast Iron: Baseplate, beam, beam support, A frames, pedestal, pulley, crank, cylinder, valve chest & cover, top & bottom cylinder covers, piston, flywheel. Brass: Slide valve, eccentric strap, valve operating block, glands, conrod bush, beam pivot support, crankshaft bearings, beam support bearings, valve gear bearings. Steel: Crankshaft, connecting rod, eccentric sheave, eccentric rod, clevis, crankpin, piston & valve rods, all materials for valve gear & beam pivot. Sundries: Detailed drawings, gaskets, viton O ring, gland packing, fixings pack. Manufacturer: Stuart Models Model / Part No: Half Beam Unmachined Set of Castings (34-50-71456)

Reviews/Comments

Add New

Intelligent Comparison

Oooops!
We couldn't find anything!
Perhaps this product's unique.... Or perhaps we are still looking for comparisons!
Click to bump this page and we'll hurry up.

Price History

Oooops!
We couldn't find any historical pricing!

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

Brass - A copper and Zinc Alloy
Diameter - A measurement across a circle passing through the middle
Engine - A machine designed to convert fuel into motion
Steel - An alloy made predominately of Iron combined with <2% carbon
Inch - Equivalent to approximately 2.5cm
Watch - A small clock designed to be worn on a person
iron - An electrical deviced used for removing creases from fabrics
iron - A chemical element (FE). The most common element on earth
Steam - Steam - water in gas form, water vapour. Commonly seen coming from a kettle
Set - a group of items usually related to one another. Some objects cannot function without the complete set of items.
Small - something that takes up less space than normal.
Bearings - A direction or a way someone moves around.
Valve - An opening and closing to control the movement of fluid through pipes.
Fixings - An action of sticking an item to another surface.

Supplier Information

My Hobby Store
MyHobbyStore publishes some of the most well known specialist hobby magasines in the UK and are responsible for some of the most loved events on model hobbies and woodworking. MyHobbyStore are passionate about specialist hobby needs which is why they supply a wide range of hobby supplies at the best prices.

A huge range including:
Model Boat Kits
Model Aircraft kits
Model Cars
Engineering Kits.

The range of kits they supply is very diverse including static models, petrol powered, electric and steam.

Delivery is around 7 days.
Page Updated: 2012-02-04 02:03:29

Community Generated Product Tags

Oh No! The productWIKI community hasn't generated any tags for this product yet!
Menu