Many older interiors & components were finished with a wrinkle effect coat which produce texture finish/ crinkle or crackle finish/ hammer finish
- whatever you want to call it! Now you can reproduce the same finish in a few hours from an aerosol spray can. Great for early M.G. dashboards, Ferrari & Lotus cam covers, electrical components, old radio cabinets, trim pieces, gauges, etc VHT High Temperature Wrinkle Plus leaves a distinctive custom crinkle finish that you both see & feel. The crackle finish is extremely durable, long lasting & chemical resistant. It is temperature resistant to 350°F (177°C) & is ideal for adding a touch of personal styling to almost any metal surface. VHT Wrinkle Plus resists colour fading, grease, degreasers & severe weather conditions. This tough durable finish is extremely resistant to rust, corrosion, chipping & cracking. Paint directly onto the bare metal to achieve the best effect (some customers have mentioned the paint will bond better with a coat of Self Etch Primer
- but that might reduce the wrinkle finish) Dries within 24 hrs of applying (does not wrinkle when cold, try to use in a warm atmosphere & when humidity is less than 60%) Ideal for: Engine Accessory Brackets, Cam Covers, Valve Covers, Metal Dashboards, Glove Boxes, Starters, Door Panels, Shifters, Alternators, Firewalls amongst others. Colours available: Black, Red, Grey, Blue 1 aerosol can covers Approx. 12-14 sq. feet. Read " How To Use Wrinkle Texture Paint " in the Technical Articles section   How To Use Wrinkle Texture Paint Many older interiors & components were finished with a wrinkle, crinkle or crackle, effect paint. Now you can reproduce the same finish in a few hours from an aerosol spray can. Great for early M.G. dashboards, Ferrari & Lotus cam covers, electrical components, old radio cabinets, trim pieces, gauges, etc Product Info VHT High Temperature Wrinkle Plus leaves a distinctive custom crinkle finish that you both see & feel. The crackle finish is extremely durable, long lasting & chemical resistant. It is temperature resistant to 350°F (177°C) & is ideal for adding a touch of personal styling to almost any metal surface. VHT Wrinkle Plus resists colour fading, grease, degreasers & severe weather conditions. This tough durable finish is extremely resistant to rust, corrosion, chipping & cracking. Paint directly onto the bare metal (but some customers have mentioned the paint will bond better with a coat of Self Etch Primer) Dries within 24 hrs of applying (does not wrinkle when cold, try to use in a warm atmosphere & when humidity is less than 60%) Ideal For Engine Accessory Brackets, Cam Covers, Valve Covers, Metal Dashboards, Glove Boxes, Starters, Door Panels, Shifters, Alternators, Firewalls amongst others. 1. Clean surface thoroughly Prepare surface by removing grease/wax, oil, loose paint, rust, etc. For best results use Frost Panel Cleaner, which will not leave any residue on the surface. Ideally use paint stripper to strip down to bare metal. Otherwise, you can scuff or sand previously painted surfaces – being sure to feather all rough edge. Clean the surface again to make sure no residue is left over. Allow to dry before applying VHT coating. 2. Mask-off surrounding areas Mask-off surrounding areas to protect from overspray. Vaseline over letters might be good idea too! 3. Shake for one full minute after marble is heard. Use at temperatures between 60 deg F (16 deg C) & 95 deg F (35 deg C) & when humidity is less than 60%. To spray, holding can upright 8-10 inches from surface to be painted & use in an even sweeping motion. Apply at least 3 heavy coats in a crosshatch pattern. First coat vertically, second coat horizontally, third coat diagonally – allowing 5 -10 minutes between each coat A relatively heavy film thickness is required for the product to Wrinkle. Avoid runs caused by excessive spray. STi Manifold – Spray on Self Etch Primer (optional) STi Manifold – Start spraying VHT Wrinkle Finish (It’s best to spray an initial thick coat followed by several more thin ones 5-10 minutes apart. The more thin coats the greater the wrinkle effect.) 4. This paint dries very slowly. A “wrinkle” finish does not appear immediately after spraying. STi Manifold – Waiting for VHT Wrinkle Finish to dry Allow about 2 hours to air dry (depending on the temperature & the light). If paint fails to wrinkle or wrinkles in an uneven pattern, apply an additional coat of paint in unwrinkled areas. Although paint appears dry, avoid any contact with surface for at least 24hours. Allow 48 hours or more before reassembling parts. To cure the paint, bake in an oven for one hour at 200 deg F (93 deg C). Process may be accelerated by the use of a heater or heat gun. Exposure to light also help to fast forward the waiting time, as the level of heat & light exposure determines the coarseness of finish. Once desired coarseness of finish is achieved, remove heat & light sources from object being coated until cured. Coating is fully cured after (minimum) 48 hours. STi Manifold – The finished article… 5. Finally you can remove the masking tape, sand & polish letters to finish the job! One Aerosol can cover Approx. 12-14 square feet. After each use, invert can & spray until clear gas comes out. If spray button becomes clogged, wipe off orifice with lacquer thinner. DO NOT stick pins or wire into can opening.  

...

Now DIYers can create an anodized look under their hoods. This unique transparent coating creates an anodized effect over properly prepared chrome, shiny bare metal & faux chrome-like surfaces for a spectacular metallic finish. VHT Anodized Colour Coat is formulated for high temperature & high performance engine paint applications. It withstands intermittent temperatures up to 550°F (228°C). To create the anodized metal look over non-metal and/or painted surfaces, first prime with VHT Anodized Base Coat. Then apply VHT Anodized Color Coat when dry. Temperature: 550°F (228°C) Applications: Engine Components, Chrome Wheels, Bumpers, Trim, Accessories Finish: Translucent Gloss Color Dry Time: Dries to the touch in 30 mins. Dries thoroughly overnight. No curing required. Aerosol: 11 oz (312g) Other Colours Available: violet, Red ...

Many older interiors & components were finished with a wrinkle effect coat which produce texture finish/ crinkle or crackle finish/ hammer finish
- whatever you want to call! Now you can reproduce the same finish in a few hours from an aerosol spray can. Great for early M.G. dashboards, Ferrari & Lotus cam covers, electrical components, old radio cabinets, trim pieces, gauges, etc VHT High Temperature Wrinkle Plus leaves a distinctive custom crinkle finish that you both see & feel. The crackle finish is extremely durable, long lasting & chemical resistant. It is temperature resistant to 350°F (177°C) & is ideal for adding a touch of personal styling to almost any metal surface. VHT Wrinkle Plus resists colour fading, grease, degreasers & severe weather conditions. This tough durable finish is extremely resistant to rust, corrosion, chipping & cracking. Paint directly onto the bare metal to achieve the best effect (some customers have mentioned the paint will bond better with a coat of Self Etch Primer
- but that might reduce the wrinkle finish) Dries within 24 hrs of applying (does not wrinkle when cold, try to use in a warm atmosphere & when humidity is less than 60%) Ideal for: Engine Accessory Brackets, Cam Covers, Valve Covers, Metal Dashboards, Glove Boxes, Starters, Door Panels, Shifters, Alternators, Firewalls amongst others. Colours available: Black, Red, Grey, Blue 1 aerosol can covers Approx. 12-14 sq. feet. Read " How To Use Wrinkle Texture Paint " in the Technical Articles section How To Use Wrinkle Texture Paint Many older interiors & components were finished with a wrinkle, crinkle or crackle, effect paint. Now you can reproduce the same finish in a few hours from an aerosol spray can. Great for early M.G. dashboards, Ferrari & Lotus cam covers, electrical components, old radio cabinets, trim pieces, gauges, etc Product Info VHT High Temperature Wrinkle Plus leaves a distinctive custom crinkle finish that you both see & feel. The crackle finish is extremely durable, long lasting & chemical resistant. It is temperature resistant to 350°F (177°C) & is ideal for adding a touch of personal styling to almost any metal surface. VHT Wrinkle Plus resists colour fading, grease, degreasers & severe weather conditions. This tough durable finish is extremely resistant to rust, corrosion, chipping & cracking. Paint directly onto the bare metal (but some customers have mentioned the paint will bond better with a coat of Self Etch Primer) Dries within 24 hrs of applying (does not wrinkle when cold, try to use in a warm atmosphere & when humidity is less than 60%) Ideal For Engine Accessory Brackets, Cam Covers, Valve Covers, Metal Dashboards, Glove Boxes, Starters, Door Panels, Shifters, Alternators, Firewalls amongst others. 1. Clean surface thoroughly Prepare surface by removing grease/wax, oil, loose paint, rust, etc. For best results use Frost Panel Cleaner, which will not leave any residue on the surface. Ideally use paint stripper to strip down to bare metal. Otherwise, you can scuff or sand previously painted surfaces – being sure to feather all rough edge. Clean the surface again to make sure no residue is left over. Allow to dry before applying VHT coating. 2. Mask-off surrounding areas Mask-off surrounding areas to protect from overspray. Vaseline over letters might be good idea too! 3. Shake for one full minute after marble is heard. Use at temperatures between 60 deg F (16 deg C) & 95 deg F (35 deg C) & when humidity is less than 60%. To spray, holding can upright 8-10 inches from surface to be painted & use in an even sweeping motion. Apply at least 3 heavy coats in a crosshatch pattern. First coat vertically, second coat horizontally, third coat diagonally – allowing 5 -10 minutes between each coat A relatively heavy film thickness is required for the product to Wrinkle. Avoid runs caused by excessive spray. STi Manifold – Spray on Self Etch Primer (optional) STi Manifold – Start spraying VHT Wrinkle Finish (It’s best to spray an initial thick coat followed by several more thin ones 5-10 minutes apart. The more thin coats the greater the wrinkle effect.) 4. This paint dries very slowly. A “wrinkle” finish does not appear immediately after spraying. STi Manifold – Waiting for VHT Wrinkle Finish to dry Allow about 2 hours to air dry (depending on the temperature & the light). If paint fails to wrinkle or wrinkles in an uneven pattern, apply an additional coat of paint in unwrinkled areas. Although paint appears dry, avoid any contact with surface for at least 24hours. Allow 48 hours or more before reassembling parts. To cure the paint, bake in an oven for one hour at 200 deg F (93 deg C). Process may be accelerated by the use of a heater or heat gun. Exposure to light also help to fast forward the waiting time, as the level of heat & light exposure determines the coarseness of finish. Once desired coarseness of finish is achieved, remove heat & light sources from object being coated until cured. Coating is fully cured after (minimum) 48 hours. STi Manifold – The finished article… 5. Finally you can remove the masking tape, sand & polish letters to finish the job! One Aerosol can cover Approx. 12-14 square feet. After each use, invert can & spray until clear gas comes out. If spray button becomes clogged, wipe off orifice with lacquer thinner. DO NOT stick pins or wire into can opening.  

...

VHT Brake Calliper paint is a High Temperature Brake Drum, Caliper & Rotor Paint has been specifically designed for the custom detailing of brake components. This innovative new finish is a 482°C (900°F) chemical resistant coating with excellent durability & weather resistance Ideal for custom detailing your vehicle. This will not chip, crack, fade or rust even under extremes of operation or road & weather conditions. It's easy to apply, dries quickly, & chemical resistant. Careful preparation is essential Aerosol: 11 oz (312g) Temperature: 900°F (482°C) Applications: Brake Calipers, Rotors, Brake Drums Finish: Satin & Gloss Dry Time: Dries to touch in 30 mins. Dries thoroughly overnight. Curing Caliper Paint VHT Caliper Paint only attains its unique properties after correct curing.
- Bake at 200°F (93°C) for 1 hour.
- The inherent heat of braking operation will also accomplish curing. Other Colours available: Bright Blue, Satin Black, Red, Yellow, Gloss Black, Gloss Clear, Real Orange.

...

Dry Time Flashes off in less than 5 minutes. Applications Brake Calipers, Rotors, Drums, Drum Brakes, General Degreasing ...

VHT Engine Enamel  has excellent durability & superior heat & chemical resistance. This is specially formulated to withstand corrosion, rust, salt spray, chemicals & additives of today’s gasoline blends & degreasers. VHT 550°F (288°C) Engine Enamel is a unique blend of urethane & ceramic resins, which produce a tough & long-lasting finish for engines, engine accessories or wherever a tough durable heat or chemical resistant finish is needed. Primer

Colour:   Light Grey Temperature:  550°F (288°C) Applications:   Headers, Engine Blocks, Starters, Brackets, Water Pumps, Valve Covers, Transmissions, Differential Covers Dry Time:   Dries to the touch in 30 mins. Dries thoroughly overnight. Curing Engine Enamel VHT Engine Enamel only attains its unique properties after correct curing. – Bake at 200°F (93°C) for 20 minutes. – The inherent heat of engine operation will also accomplish curing.

...

VHT Flame Proof Coating will renew & extend the life of any surface exposed to extremely high temperatures. This unique coating is a matte finish, silicone ceramic base widely used by the automotive industry on exhaust systems & the aerospace industry for jet engines, re-entry vehicles & other high temperature applications. VHT Flame Proof Coating will withstand temperatures up to 1093°C (2000°F) & is ideal to be used on headers, exhaust systems, or wherever an extreme temperature coating is needed. Temperature: 704°C-1093°C (1300°F-2000°F) Applications: Headers, Exhaust Manifolds, Piston Domes, Inside Heads Finish: Flat Dry Time: Curing time required & can be done on or off vehicle (see below) Curing Flame Proof VHT Flame Proof High Temperature Paint only attains its unique properties after correct curing (refer to instructions on the can). On the Vehicle Off the Vehicle
- Paint must be completely dry before curing
- Run at idle for 10 minutes
- Cool for 20 minutes
- Run at idle for 20 minutes
- Cool for 20 minutes
- Paint must be completely dry before curing
- Heat to 250°F (121°C) for 30 minutes
- Cool for 30 minutes
- Heat to 400°F (204°C) for 30 minutes
- Cool for 30 minutes
- Heat to 650°F (343°C ) for 30 minutes Caution: Do not exceed the temperature of the least heat tolerant component or the base metal Aerosol: 11 oz (312g) Paint Colours Available: Satin Clear, Cast Iron, Flat Black, Flat Silver, Flat White, Flat Red Primer

Colour: Flat White












...

VHT Engine Enamel has excellent durability & superior heat & chemical resistance. This is specially formulated to withstand corrosion, rust, salt spray, chemicals & additives of today’s gasoline blends & degreasers. VHT 550°F (288°C) Engine Enamel is a unique blend of urethane & ceramic resins, which produce a tough & long-lasting finish for engines, engine accessories or wherever a tough durable heat or chemical resistant finish is needed. VHT Engine Enamel High Temperature Paint Colours: Gloss Clear, Ford Grey, Gloss Black, Satin Black, Chevy Orange Primer

Colour: Light Grey Temperature: 550°F (288°C) Applications: Headers, Engine Blocks, Starters, Brackets, Water Pumps, Valve Covers, Transmissions, Differential Covers Dry Time: Dries to the touch in 30 mins. Dries thoroughly overnight. Curing Engine Enamel VHT Engine Enamel only attains its unique properties after correct curing.
- Bake at 200°F (93°C) for 20 minutes.
- The inherent heat of engine operation will also accomplish curing.



...

VHT Copper Gasket Cement has been formulated with the same ingredients as our world-renowned high temperature coatings. VHT Copper Gasket Cement maintains excellent adhesion under severe pressure & heat fluctuations. This high-metallic formula assures tight seals on cork, paper & metal gaskets. VHT Copper Gasket Cement has been extensively tested on racing engines in the field & on dynamometers, where it has met & exceeded the high-compression & high temperature requirements of these mega horsepower engines. Applications: Head Gaskets, Rubber Hoses, Cork Gaskets, Water Pump Gaskets, Threaded Fittings, AN Fittings, Paper Gaskets, Oil Pan Gaskets, Metal Gaskets ...

VHT 550°F (288°C) Engine Enamels™ are available in a wide range of colors, including exact match factory colors. All colors have excellent durability & superior heat & chemical resistance. They are specially formulated to withstand corrosion, rust, salt spray, chemicals & additives of today's gasoline blends & degreasers. VHT 550°F (288°C) Engine Enamels™ are a unique blend of urethane & ceramic resins, which produce a tough & long-lasting finish for engines, engine accessories or wherever a tough, durable heat or chemical-resistant finish is needed. Temperature: 550°F (288°C) Intermittent Dry Time: Dries to the touch in 30 mins. Dries thoroughly overnight. Applications: Headers, Engine Blocks, Starters, Brackets, Water Pumps, Valve Covers, Transmissions, Differential Covers Curing Engine Enamel™ Engine Enamel™ only attains its unique properties after correct curing. Bake at 200°F (93°C) for 20 minutes. The inherent heat of engine operation will also accomplish curing. ...