Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Vinyl Kleen.
- Dampen a clean, soft, lint free cloth with Vinyl Prep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Vinylprep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Liquid Plastic   for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect.



...

Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Vinyl Kleen.
- Dampen a clean, soft, lint free cloth with Vinyl Prep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Vinyl Prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Frost Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect.



...

Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Vinyl Kleen
- Dampen a clean, soft, lint free cloth with Vinyl Prep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Vinyl prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray  Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect.



...

The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple: – Clean the interior by removing dirt, grease & silicones with  Vinyl Kleen. – Dampen a clean, soft, lint free cloth with  Vinyl Prep  and wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again. – If treating semi-rigid, polythene & polypropylene plastics it is essential to use  Adhesionaid  before applying Liquid Plastic. Allow Vinylprep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic. – Spray  Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. ...

The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple: – Clean the interior by removing dirt, grease & silicones with  Vinyl Kleen. – Dampen a clean, soft, lint free cloth with  Vinyl Prep  and wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again. – If treating semi-rigid, polythene & polypropylene plastics it is essential to use  Adhesionaid  before applying Liquid Plastic. Allow Vinylprep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic. – Spray  Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. ...

Liquid Wrap Aerosols – Flexible Rubber Coating Give your car a brand new look & at the same time protect the bodywork from the stone chips & bad weather conditions. The Brand – New – Look has never been easier! Frost Liquid Wrap is a flexible liquid coating applied to the vehicle in numerous coats to build up to a professional finish, not only visually, but as a protection for the original paint work, alloy, plastic, rubber or any exterior or interior surface, to which it is applied. Liquid Wrap is specially designed to be spray ed on – Unlike Plasti Dip texture, you don’t need to use any extra thinners to give you the thin, air brush finish. Just simply deliver several wet coats & you will be impressed with the final result! This is not a general purpose rubber coating designed for dipping tools – The rubber coating spray from Frost Auto Restoration Techniques  is manufactured specifically for use on vehicles & produces a smooth & flawless, texture free, near perfect finish. This product is manufactured in UK & for the European market!

Features:
- Stays flexible
- Easy to apply
- Strong protection but also Peel-able
- Non sagging formulation
- No thinner needed Also Available in 3.78L can.






...

Liquid Wrap Aerosols – Flexible Rubber Coating Give your car a brand new look & at the same time protect the bodywork from the stone chips & bad weather conditions. The Brand – New – Look has never been easier! Frost Liquid Wrap is a flexible liquid coating applied to the vehicle in numerous coats to build up to a professional finish, not only visually, but as a protection for the original paint work, alloy, plastic, rubber or any exterior or interior surface, to which it is applied. Liquid Wrap is specially designed to be spray ed on – Unlike Plasti Dip texture, you don’t need to use any extra thinners to give you the thin, air brush finish. Just simply deliver several wet coats & you will be impressed with the final result! This is not a general purpose rubber coating designed for dipping tools – The rubber coating spray from Frost Auto Restoration Techniques  is manufactured specifically for use on vehicles & produces a smooth & flawless, texture free, near perfect finish. This product is manufactured in UK & for the European market!

Features:
- Stays flexible
- Easy to apply
- Strong protection but also Peel-able
- Non sagging formulation
- No thinner needed Also Available in 3.78L can.






...

Liquid Wrap Aerosols – Flexible Rubber Coating Give your car a brand new look & at the same time protect the bodywork from the stone chips & bad weather conditions. The Brand – New – Look has never been easier! Frost Liquid Wrap is a flexible liquid coating applied to the vehicle in numerous coats to build up to a professional finish, not only visually, but as a protection for the original paint work, alloy, plastic, rubber or any exterior or interior surface, to which it is applied. Liquid Wrap is specially designed to be spray ed on – Unlike Plasti Dip texture, you don’t need to use any extra thinners to give you the thin, air brush finish. Just simply deliver several wet coats & you will be impressed with the final result! This is not a general purpose rubber coating designed for dipping tools – The rubber coating spray from Frost Auto Restoration Techniques  is manufactured specifically for use on vehicles & produces a smooth & flawless, texture free, near perfect finish. This product is manufactured in UK & for the European market!

Features:
- Stays flexible
- Easy to apply
- Strong protection but also Peel-able
- Non sagging formulation
- No thinner needed Also Available in 3.78L can.






...

Liquid Wrap Aerosols – Flexible Rubber Coating Give your car a brand new look & at the same time protect the bodywork from the stone chips & bad weather conditions. The Brand – New – Look has never been easier! Frost Liquid Wrap is a flexible liquid coating applied to the vehicle in numerous coats to build up to a professional finish, not only visually, but as a protection for the original paint work, alloy, plastic, rubber or any exterior or interior surface, to which it is applied. Liquid Wrap is specially designed to be spray ed on – Unlike Plasti Dip texture, you don’t need to use any extra thinners to give you the thin, air brush finish. Just simply deliver several wet coats & you will be impressed with the final result! This is not a general purpose rubber coating designed for dipping tools – The rubber coating spray from Frost Auto Restoration Techniques  is manufactured specifically for use on vehicles & produces a smooth & flawless, texture free, near perfect finish. This product is manufactured in UK & for the European market!

Features:
- Stays flexible
- Easy to apply
- Strong protection but also Peel-able
- Non sagging formulation
- No thinner needed Also Available in 3.78L can.






...

Liquid Wrap Aerosols – Flexible Rubber Coating Give your car a brand new look & at the same time protect the bodywork from the stone chips & bad weather conditions. The Brand – New – Look has never been easier! Frost Liquid Wrap is a flexible liquid coating applied to the vehicle in numerous coats to build up to a professional finish, not only visually, but as a protection for the original paint work, alloy, plastic, rubber or any exterior or interior surface, to which it is applied. Liquid Wrap is specially designed to be spray ed on – Unlike Plasti Dip texture, you don’t need to use any extra thinners to give you the thin, air brush finish. Just simply deliver several wet coats & you will be impressed with the final result! This is not a general purpose rubber coating designed for dipping tools – The rubber coating spray from Frost Auto Restoration Techniques  is manufactured specifically for use on vehicles & produces a smooth & flawless, texture free, near perfect finish. This product is manufactured in UK & for the European market!

Features:
- Stays flexible
- Easy to apply
- Strong protection but also Peel-able
- Non sagging formulation
- No thinner needed Also Available in 3.78L can.






...