Hotcoat Powder Coating (1 LB)  for  Hot Coat Powder Coating Gun. Powder coating  allows you to coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black – Orange – Brown – Yellow – Green – Bright Red – Silver – White – Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021    

...

Product

Features: OEM  finish on plastic bumper repair/plastic trim repair Coarse texture/fine texture from

...

Compact Floor Mounted Metal Bender Package Dimensions: 92cm x 28cm x 27cm Net Weight 24kgs Gross Weight 26kgs ...

The Complete Shrinker Stretcher with Foot Operated Stand can be used to fabricate or repair metal work around wheel arches, door edges, window frames, rain channels...almost any metal fabrication requiring a combination curve & angle especially those awkward areas around headlights. Use the shrinker to contract metal for inside curves: use the stretcher to expand metal for outside curves. The Complete Shrinker / Stretcher Stand Set,

Includes:: two separate pedal driven shaping units, one to stretch & one to shrink, mounted on the st&, along with two handy castors for free movement around the workshop. The Frost stretching/ shrinking machine is a clamping device which, under the influence of the lever, will squeeze whichever jaws are mounted in it. The jaws can be swapped for different jobs. A bespoke stand is available, but it’s easy enough to bolt the machine body to a bench or simply to hold it in a vice. Fully Assembled Dimensions:

Height: 110cm

Width: 125cm

Depth: 56cm Read " How Do I Use the Shrinking / Stretching Machine? " & " 10 MUST-HAVE Restoration Tools " from Technical Article. * Colour might be different from the picture.*







...

Frost Copper Anti-Seize Aerosol eliminates pitting, rusting thread distortion, grabbing & seizure. It lubricates, seals & protects at temperatures up to 1200°C. ideal to be used in pressure gaskets, hoses & hydraulic fittings. ...

Drill & Tapping spray for cleaner cut threads, smoother surface finishes in tapping, threading, reaming, boring, broaching & engraving. Stops galling, the main cause of tap breakage. ...

Frost Etch Primer Surface Preperation De-rust, abrade & clean surfaces prior to coating. The surface must be free from all contamination including rust, grease & moisture. Before use, carefully read & note the warning text on label. ...

SHAKE WELL BEFORE USE Frost Extreme Chassis Black GLOSS* is ideal for a full car chassis, sub frames & chassis components. It gives your parts a  Superb Gloss look while giving better protection from road dirt & harsh chemicals. Frost Extreme Chassis Black offers excellent UV protection & will withstand temperatures up to 150°C. The formula can be applied direct to bare metal. Ascertain suitability over etch primer using a small test area. Aerosol 500ml
- Covers 6 -7 sq ft.

Features:
- Excellent Resistance From Chips, Mud & Salt Corrosion
- Good Resistance To Oils, Fuels, Brake fluid & Other Automotive Liquids * This is not HIGH GLOSS finish. Direction 1. Surface must be clean & dry before painting. Use Frost Chassis Clean (C265) to remove heavy deposits of grease & oil, followed by Frost Panel Cleaner (C110) for surface cleaning. Can be used over bare metal, but to increase adhesion & durability paint over Frost Grey Primer (P270) or similar. Ascertain suitability over etch primer using a small test area. For best results, use at temperatures between 20 to 30 deg C & when humidity is less than 50%. 2. Wait 4 hours (Lightly rub down the surface after 36 hours) & topcoat with Frost Extreme Chassis Black. 3. Shake can vigorously for at least one minute before use & then again between each coat. Spray surface with steady, even strokes at a distance of 8-10 inches. Several light coats give a better finish than one heavy coat. 4. Apply enough paint to achieve full covering. For best results, apply a maximum of two coats of Primer & two coats Frost Extreme Chassis Black. 5. If the spray button becomes clogged, remove to nozzle & wipe off the orifice with thinners. 6. Once the desired finish is achieved, allow it to dry for a minimum of 4 hours before use, it cures fully in 12-24 hours. Caution Pressurised container: protect from sunlight & do not expose to temperatures exceeding 50 deg. C. Do not pierce or burn, even after use. Do not spray on a naked flame or any incandescent material. MADE IN THE UK




...

SHAKE WELL BEFORE USE Frost Extreme Chassis Black Satin (was High Performance Frame & Chassis) is ideal for a full car chassis, sub frames & chassis components. It gives your parts the Original Satin look while giving better protection from road dirt & harsh chemicals. Frost Extreme Chassis Black offers excellent UV protection & will withstand temperatures up to 150°C. The formula can be applied direct to bare metal. Ascertain suitability over etch primer using a small test area. Aerosol 500ml
- Covers 6 -7 sq ft.

Features:
- Excellent Resistance From Chips, Mud & Salt Corrosion
- Good Resistance To Oils, Fuels, Brake fluid & Other Automotive Liquids Direction 1. Surface must be clean & dry before painting. Use Frost Chassis Clean (C265) to remove heavy deposits of grease & oil, followed by Frost Panel Cleaner (C110) for surface cleaning. Can be used over bare metal, but to increase adhesion & durability paint over Frost Grey Primer (P270) or similar. Ascertain suitability over etch primer using a small test area. For best results, use at temperatures between 20 to 30 deg C & when humidity is less than 50%. 2. Wait 4 hours (Lightly rub down the surface after 36 hours) & topcoat with Frost Extreme Chassis Black. 3. Shake can vigorously for at least one minute before use & then again between each coat. Spray surface with steady, even strokes at a distance of 8-10 inches. Several light coats give a better finish than one heavy coat. 4. Apply enough paint to achieve full covering. For best results, apply a maximum of two coats of Primer & two coats Frost Extreme Chassis Black. 5. If the spray button becomes clogged, remove to nozzle & wipe off the orifice with thinners. 6. Once the desired finish is achieved, allow it to dry for a minimum of 4 hours before use, it cures fully in 12-24 hours. Caution Pressurised container: protect from sunlight & do not expose to temperatures exceeding 50 deg. C. Do not pierce or burn, even after use. Do not spray on a naked flame or any incandescent material. MADE IN UK




...

The perfect spray paint kit for your chassis! Frost Extreme Chassis Paint (was High Performance Frame & Chassis) is ideal for a full car chassis, sub frames & chassis components. It gives your parts the Original Satin look while providing substantial protection from road dirt, salt & hash chemicals. Frost Extreme Chassis Paint offers excellent UV protection & will withstand temperature up to 150 deg C. The formula can be applied direct to bare metal. Ascertain suitability over etch primer using a small test area. Fast drying, easy to use, durable finish, & great value
- It is the easy way to make something old appear new! Kit contents :
- 1 x Frost Panel Cleaner Pre Painting Prep Aerosol (500ml)
- 1 x Frost Grey Primer Aerosol (500ml)
- 2 x Frost Extreme Chassis Black Paint Aerosol
- Satin Black (500ml)

Features:
- Excellent Resistance From Chips, Mud & Salt Corrosion
- Good Resistance To Oils, Fuels, Brake fluid & Other Automotive Liquids Direction 1. Surface must be clean & dry before painting. Use Frost Chassis Clean (C265) to remove heavy deposits of grease & oil, followed by Frost Panel Cleaner (C110) for surface cleaning. Can be used over bare metal, but to increase adhesion & durability paint over Frost Grey Primer (P270) or similar. Ascertain suitability over etch primer using a small test area. For best results, use at temperatures between 20 to 30 deg C & when humidity is less than 50%. 2. Wait 4 hours (scuff surface after 36 hours) & top-coat with Frost Extreme Chassis Paint. 3. Shake can vigorously for at least one minute before use & then again between each coat. Spray surface with steady, even strokes at a distance of 8-10 inches. Several light coats give a better finish than one heavy coat. 4. Apply enough paint to achieve full covering. For best results, apply a maximum of two coats of Primer & two coats Frost Extreme Chassis Paint. 5. If the spray button becomes clogged, remove to nozzle & wipe off the orifice with thinners. 6. Once the desired finish is achieved, allow it to dry for a minimum of 4 hours before use, it cures fully in 12-24 hours. Caution Pressurised container: protect from sunlight & do not expose to temperatures exceeding 50 deg. C. Do not pierce or burn, even after use. Do not spray on a nacked flame or any incandescent material. SHAKE WELL BEFORE USE
- MADE IN UK  









...