These cove style cutters with two flutes, give radiused grooves for decorative panel finishes & board edges. For deep channels, take a series of passes. Ref. C056A is used with the Trend Draining Groove Jig. D=1 inch. D=25.4 mm. Cut length=5/8 inch. Cut length=15.9 mm. Overall length=56.5 mm. R=12.7 mm. Shank Diameter=1/4 inch. ...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece. D=38.0 mm. Cut length=3/4 inch. Cut length=19.1 mm. B=9.5 mm. B2=12.7 mm. R=1/2 inch. R=12.7 mm. Shank Diameter=1/4 inch. ...

Attractive edge moulds a full corner bead can be produced by making a second pass at 90. Used on all man-made boards such as medium density fibre board chipboard & also natural timbers & most plastics. T.C.T. Shank = 1/4 in. R = 4.8 mm. D = 26 mm. d = 22 mm. C = 16 mm. B = 15.9 mm. Craft Range
- They can be used on all man-made boards such as medium density fibre board chipboard & also natural timbers & most plastics. Bead, Reed Cutters Bead & Reed cutters are ideally suited to form straight or curved decorative edge mouldings on table tops chair legs & frames. They can also be used to produce complete round over profiles for window boards & stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications. Certain staff bead cutters are used to join boards & produce hinged joints for table tops.
...

This two wing slotting cutter is ideal for grooving & rebating operations. A 1/2 in diameter bearing is supplied with every cutter. Depth of cut can be changed by purchasing alternative bearing sizes. T.C.T. Shank = 1/4 in. C = 6.3 mm. (Slots) Depth with standard cutter = 3/8 in. ...

This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slightly longer cut than the length of the biscuit is required for ease of alignment during assembly. Supplied with instructions. No. 0
- 45 mm. x 15 mm. x 4 mm. Suitable for 8-12 mm. boards Use bearing B19A 9.05 mm. depth. No. 10
- 53 mm. x 19 mm. x 4 mm. Suitable for 13-18 mm. boards Use bearing B16A 10.6 mm. depth. No. 20
- 58 mm. x 23 mm. x 4 mm. Suitable for 19 mm. +- board Use bearing B127AD1 37.2 mm. Cut length 4 mm. B 12.7 mm. B2 16.0 mm. B3 19.0 mm. Shank = 1/2 in.


...

Two fluted Tungsten Carbide Tipped straight cutters which are suitable for a wide range of applications such a engraving grooving rebating & shallow mortising. They can be used on a wide range of materials such as softwoods hardwoods MDF plywood & chipboard. All cutters have a bottom cut feature. When deep cuts are required more than one pass should be taken. Shank. 1/4 in. Suitable for a wide range of applications such as engraving grooving rebating & shallow mortising. Use on softwoods hardwoods MDF plywood & chipboard. All cutters have a bottom cut feature. D1 1/2 inch D1 12.7 mm. Cut length 2 inches Cut length 50 mm. Shank Diameter 1/2 inch. ...

Suitable for a wide range of applications such as engraving, grooving, rebating & shallow mortising. Use on softwoods, hardwoods, MDF, plywood & chipboard. All cutters have a bottom cut feature. D=15/32 inch. D=12 mm. Cut length=2 1/2 inches. Cut length=63 mm. Shank Diameter=1/2 inch. ...

These cutters are self-guiding & can be used to produce rebates, lap joints, tongues & rebated corners. When using bearing Ref. B95A make two passes when a full depth of cut is required. D=31.8 mm. Cut length=15.9 =12.7 &9.5 mm. E=9.5 mm. E2=11.1 mm. Shank Diameter=1/2 inch. ...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece. D=44.5 mm. Cut length=22 mm. B=9.5 mm. B2=12.7 mm. R=5/8 inch. R=16 mm. Shank Diameter=1/2 inch. ...

Recessing cutter will accommodate the Schlegel Aquamac 63 weather strip system & allows for a particularly small gap between sash & frame. The slot can be positioned part way down the side of the rebate, or at the bottom of the rebate. D=41.3 mm. D2=28.3 mm. C=4.8 mm. C2=2.7 mm. Overall length=67 mm. B=22 mm. Shank Diameter=1/2 inch. ...