Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece. D=38.0 mm. Cut length=3/4 inch. Cut length=19.1 mm. B=9.5 mm. B2=12.7 mm. R=1/2 inch. R=12.7 mm. Shank Diameter=1/4 inch. ...

Attractive edge moulds a full corner bead can be produced by making a second pass at 90. Used on all man-made boards such as medium density fibre board chipboard & also natural timbers & most plastics. T.C.T. Shank = 1/4 in. R = 4.8 mm. D = 26 mm. d = 22 mm. C = 16 mm. B = 15.9 mm. Craft Range
- They can be used on all man-made boards such as medium density fibre board chipboard & also natural timbers & most plastics. Bead, Reed Cutters Bead & Reed cutters are ideally suited to form straight or curved decorative edge mouldings on table tops chair legs & frames. They can also be used to produce complete round over profiles for window boards & stair tread nosings. Cutters can be combined to form compounded one-off mouldings for individual applications. Certain staff bead cutters are used to join boards & produce hinged joints for table tops.
...

This two wing slotting cutter is ideal for grooving & rebating operations. A 1/2 in diameter bearing is supplied with every cutter. Depth of cut can be changed by purchasing alternative bearing sizes. T.C.T. Shank = 1/4 in. C = 6.3 mm. (Slots) Depth with standard cutter = 3/8 in. ...

This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slightly longer cut than the length of the biscuit is required for ease of alignment during assembly. Supplied with instructions. No. 0
- 45 mm. x 15 mm. x 4 mm. Suitable for 8-12 mm. boards Use bearing B19A 9.05 mm. depth. No. 10
- 53 mm. x 19 mm. x 4 mm. Suitable for 13-18 mm. boards Use bearing B16A 10.6 mm. depth. No. 20
- 58 mm. x 23 mm. x 4 mm. Suitable for 19 mm. +- board Use bearing B127AD1 37.2 mm. Cut length 4 mm. B 12.7 mm. B2 16.0 mm. B3 19.0 mm. Shank = 1/2 in.


...

This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slightly longer cut than the length of the biscuit is required for ease of alignment during assembly. Supplied with instructions. No. 0
- 45 mm. x 15 mm. x 4 mm. Suitable for 8-12 mm. boards Use bearing B19A 9.05 mm. depth. No. 10
- 53 mm. x 19 mm. x 4 mm. Suitable for 13-18 mm. boards Use bearing B16A 10.6 mm. depth. No. 20
- 58 mm. x 23 mm. x 4 mm. Suitable for 19 mm. +- board Use bearing B127AD1 37.2 mm. Cut length 4 mm. B 12.7 mm. B2 16.0 mm. B3 19.0 mm. Shank = 1/4 in.


...

Suitable for a wide range of applications such as engraving, grooving, rebating & shallow mortising. Use on softwoods, hardwoods, MDF, plywood & chipboard. All cutters have a bottom cut feature. D=15/32 inch. D=12 mm. Cut length=2 1/2 inches. Cut length=63 mm. Shank Diameter=1/2 inch. ...

These cutters are self-guiding & can be used to produce rebates, lap joints, tongues & rebated corners. When using bearing Ref. B95A make two passes when a full depth of cut is required. D=31.8 mm. Cut length=15.9 =12.7 &9.5 mm. E=9.5 mm. E2=11.1 mm. Shank Diameter=1/2 inch. ...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. Bullnose mouldings can also be produced by taking a second pass from the opposite side of the workpiece. D=44.5 mm. Cut length=22 mm. B=9.5 mm. B2=12.7 mm. R=5/8 inch. R=16 mm. Shank Diameter=1/2 inch. ...

Recessing cutter will accommodate the Schlegel Aquamac 63 weather strip system & allows for a particularly small gap between sash & frame. The slot can be positioned part way down the side of the rebate, or at the bottom of the rebate. D=41.3 mm. D2=28.3 mm. C=4.8 mm. C2=2.7 mm. Overall length=67 mm. B=22 mm. Shank Diameter=1/2 inch. ...

For either frame or door applications, with standard Intumescent Strip. Neatly cuts grooves on doors or frames to accept Intumescent Strip which enables the formation of effective barriers to both fire & smoke. By using alternative ball bearings diameters other seal thicknesses can be introduced. Alternative bearings can be purchased to suit other thicknesses. For 4.0 mm. thick & 10.0 mm. width intumescent strip. D= 40 mm. C= 10 mm. B= 32 mm. E= 4 mm. Shank Diameter= 1/2 inch. ...