Ovollo & rounding over bearing guided cutters are ideal for curved work they can be used on natural timbers man-made particles & fibre boards. Popular uses include edging window frames glazing bars cabinets table tops pencil rounds trophies shelves & fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings larger bearing removes the quirk producing a round over profile. Tooling: T.C.T. 1/2 in Shank. R = 19 mm. D = 51 mm. C = 25 mm. Bearings = 9.5 & 12.7 mm. ...

These types of cutters are used for edging work & chamfer cutting on man made fibre boards natural timbers & plastics. Tools are offered to produce various angles for chamfering. Ball bearing & pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making freehand engraving cabinet making & decorative joinery. T.C.T. 1/2 in Shank. A = 45 C1 = 19 mm. C2 = 26 mm. D = 51.5 mm. B = 12.7 mm. ...

Popular rebate sets which include different size bearings for a choice of rebates. They provide easy setting up & accurate depth of cut. Ideal for rebating straight & shaped work pieces. Tooling TCT. By changing the bearing the size of the rebate can be altered. Supplied with four bearings. 19 mm. Bearing gives rebate of 7.9 mm. 16 mm. Bearing gives rebate of 9.5 mm. 12.7 mm. Bearing gives rebate of 11.1 mm. 9.5 mm. Bearing gives rebate of 13.7 mm. D = 3.5cm. C = 12.7 mm. 1/2 in Shank. By changing the bearing the size of the rebate can be altered. Supplied with 4 bearings. Use of: 19 mm. Bearing gives rebate of 7.9 mm. 16 mm. Bearing gives rebate of 9.5 mm. 12.7 mm. Bearing gives rebate of 11.1 mm. 9.5 mm. Bearing gives rebate of 12.7 mm. D = 3.5cm. C = 12.7 mm. ...

Popular rebate sets which include different size bearings for a choice of rebates. They provide easy setting up & accurate depth of cut. Ideal for rebating straight & shaped work pieces. Tooling TCT. By changing the bearing the size of the rebate can be altered. Supplied with four bearings. 19 mm. Bearing gives rebate of 7.9 mm. 16 mm. Bearing gives rebate of 9.5 mm. 12.7 mm. Bearing gives rebate of 11.1 mm. 9.5 mm. Bearing gives rebate of 13.7 mm. D = 3.5cm. C = 12.7 mm. 1/4 in. Shank. By changing the bearing the size of the rebate can be altered. Supplied with four bearings. 19 mm. Bearing gives rebate of 7.9 mm. 16 mm. Diameter gives rebate of 9.5 mm. 12.7 mm. Diameter gives rebate of 11.1 mm. 9.5 mm. Diameter gives rebate of 13.7 mm. D = 3.5cm. C = 12.7 mm. ...

Bearing guided rebate set for straight of curved work this set is ideal for either stationary or portable routers. The standard rebate depth is 19.1 mm. (when using 12.7 mm. bearing) Available as extras are different size bearing which when fitted will give various rebate sizes. TCT 1/2 in Shank. Diameter = 50.8 mm. Cutting length = 22.5 mm. Rebate = 19.1 mm., 15.9 mm. ...

Self-guiding triple flute cutters provide a super fine finish & longer life. Suitable for laminate or plywood overlay. An industrial profiling tool for longer runs of work when a clean finish is needed. Tooling: T.C.T. 1/4 in. Shank. A Angle = 90 C = 25.4 mm. D = 12.7 mm. ...

Profilers with Shank mounted bearings for guidance for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight & curved work. For profiling & rebating applications only. NOT for plunge cutting or grooving. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide 1/4 in. Shank. Angle A = 90 D = 15.9 mm. C = 25 mm. ...

Profilers with Shank mounted bearings for guidance for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight & curved work. For profiling & rebating applications only. NOT for plunge cutting or grooving. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide 1/4 in. Shank. Angle A = 90 D = 12.7 mm. C = 9.5 mm. ...

Profilers with Shank mounted bearings for guidance for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight & curved work. For profiling & rebating applications only. NOT for plunge cutting or grooving. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten/4 in. Shank. Angle A = 90 D = 15.9 mm. C = 19.1 mm. ...

Ovollo & rounding over bearing guided cutters are ideal for curved work they can be used on natural timbers man-made particles & fibre boards. Popular uses include edging window frames glazing bars cabinets table tops pencil rounds trophies shelves & fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings larger bearing removes the quirk producing a round over profile. Tooling: T.C.T. 1/4 in. Shank. R = 7.9 mm. D = 28 mm. C = 12.7 mm. Bearings = 9.5 & 12.7 mm. ...