The power pack module is designed to actuate up to 36 FS20 actors in combination with the FS20 EAM radio receiver (not included in scope of delivery)
- e.g.FS20 DH20 or FS20 SH. It provides the FS20 EAM radio receiver with voltage, amplifies the data received from this module & transmits them to the FS20 actors via a 2-wire bus.
...

The FS20 IRP simplifies a programming & a configuration of the FS20 systems completely substantially. It extends besides the functional range of selected transmitters of the FS20 program All configuration of the transmitters (addressing, command assignment, switching-on or dimming time, channel assignment, etc.) are to be clearly set & can documented via the provided Windows software in addition for every key of the transmitter, macros with up to 3 actions can be stored
- so far that was not possible on the normal programming of the! The finished configurations can be stored on the PC & released by USB (Universal Serial Bus) to the FS20 IRP This is then released by infrared on the FS20 transmitter
...

The FS20 FMS radio-controls any FS20 switch actors such as the FS20 ST radio socket or the surface-mounted FS20 AS4 4-channel switch as soon as the main equipment connected to it is switched on or off. This permits having the garden or house lighting switched on as soon as the garage door is opened, for instance. A timer function can be used to switch off the consumers automatically.
You can also use it the opposite way round, e.g. to tell you when the washing machine has finished. In this case the FS20 FMS signals that the washing machine has finished & sends a switch command to the FS20 SIG radio transmitter, for instance. Here the timer can be programmed to delay the transmitter signal so that the transmitter only transmits after the programmed delay. For appliances that consume power when they are switched off (st&-by), you can set the response threshold of the FS20 FMS in several increments. As a real FS20 device, the FS20 FMS can be integrated into the FS20 code & address system.
...

With the radio repeater RPT FS20 you can increase the range of the transmitter of your wireless switching system FS20. To allow an easy access even in adverse conditions, such as radio massive steel reinforcement in concrete ceilings reliable Radio-switch-signal transmission. Since the signals can be repeated up to twice, you can reach 3 times the transmitter range with 2 repeaters. The repeater is suitable for transmitting dimming commands only to a certain extent. Thanks to the practical design that fits into the plug housing, the power supply to the repeater is extremely easy, & the existing socket can still be used because the mains voltage is switched through. ...

Using programmable roller shutter control, it is possible to realise a visually unnoticed radio controlling of electric-driven roller shutters, awnings & venetian blinds. Roller shutter switch can be operated though compact flush-mounted housing & all FS20-centres are controlled through the sender of FS20-system & also through direct key. In addition to manual & time- or event-driven switching function, a programmable timer function is available to adjust runtime of the actuator. ...

This surface-mounted radio switch means that you can operate two different consumers simultaneously in combination with your FS20 radio switch system or via the FHZ 1000 Radio Home Centre. Here two potential-free relay DTCs are available that switch on alternately (never simultaneously). This even makes reliable control of directions possible as required with electric door & gate drives. Three operating modes allow activating a switch output, e.g. for the duration of actuating a button on the transmitter, for a freely programmable time ranging from 1 s to 4.5 h or permanently up to the next switch-off pulse of the transmitter. Thanks to simple parallel connection to already existing buttons, installation into existing systems is no problem & existing functions are in no way affected. ...

This radio twilight transmitter is designed to telecontrol various radio switches of the FS20 radio system. It can telecontrol these on two channels based on the intensity of the ambient brightness. The brightness response threshold & the type of switch command execution on the receiver, the switching direction & the filter time to avoid fast switching processes can be programmed separately for each channel. in addition, the timers of the respective FS20 receivers can be programmed from the twilight transmitter. ...

Switch module for use in the FS20 DIN rail system. The module can be operated directly on the device itself, as well as via any transmitter of the FS20 radio switch system. A programmable timer is integrated (duty cycle 1 s to 4.5 h). Power supply & switch signal feeding via the FS20 SEH power pack. Radio reception via the FS20 EAM radio receiver in combination with the power pack. ...

Solution for all switching funcitons is about protecting the switch from environmental impacts, pollutants, moisture etc. Proximity switch is responsive to approaching hand by transmitting radio signals that simultaneously

Includes:: the operating duration of the load as well as mode of the switching commands. If necessary, an internal signal-transmittor can be switched on for operating confirmation.

...

The FS20-Touch control-transmitter unit for the UP wall assembly works with six keys on basis of proximity sensors. Optionally three on/off functions are available with in each pair of keys or six functions with a key The transmission unit is designed for the installation in UP switch box the adjustment of the adapter frame takes place at the set switching program. The Touch control can be comfortably programmed via PC over the USB (Universal Serial Bus) infrared Programmer (64 63 95). ...