The false ceiling radio can be placed anywhere due to its compact casing. The radio can be activated via the special remote control provided in the set or via any other FS20 remote control, FS20 time switch or a FS20 motion detector. The adjustable sensitivity of the scan with 8 memory slots helps to program the desired station. Only 230 V / AC & the desired speaker is required for start up If desired, even Status LEDs & an additional audio device (For example: MP3 Player) can be attached. ...

The dimmer is powered via an economical external DC source, which can be adapted to the power required. It can be operated via FS20 remote control or via an external button, & emergency control
directly from the device is also possible. As well as the manual dimming function, three separately programmable automatic timers are available: A
switch-off timer, a slow-on timer (fade in) & a slow-off timer (fade out). The timers can be programmed for between 1 s & 4.5 h.

...

This dimmer is designed for use in the FS20 DIN rail system. The dimmer can be operated directly on the device as well as via any transmitter of the FS20 radio switch system. Incl. built-in timer (duty cycle programmable between 1 s & 4.5 h). Power as well as the switch signal lead is supplied via the FS20 SEH power adapter. Radio reception via the FS20 EAM radio receiver in combination with the power pack. ...

The radio plug-in dimmer has the same construction as the radio switching socket FS20ST Part No. 62 30 04-62. However, the connected lamps can not only be switched, but instead their brightness can also be controlled. It can be used with conventional bulbs (resistive loads) & conventional halogen transformers (inductive loads). The integrated timer allows switching on briefly for 1 s up to 4.5 h or dimming up & down softly during the timer period. ...

The upper-and lower dimming takes place by capacitive contact-free sensors, in which the position of sensor surface & light is determined by finger. Totally 15 brightness level & out are available, which are not necessarily navigated along the "slider-way" by finger; but certainly selection of the favourite brightness spot is possible directly by the tip. the last position of finger is carried as FS20-command for Dimmer The FS20-Dimmer-Slider is set very flexibly, as the sender unit is provided for the installation in Standard-UP-switch & by the help of adapter frames (refer Internet-offer), the adaptation to the respective switching programme can take place in house. The programming of FS20-command can follow separately on two canals so that two independent illuminated scenes are controlled. The programming can take place by integrated IR- receiver diode & can also follow via FS20 IRP (64 63 95). By three covers with delivery (each 1 x in black & in white is pressed, 1 x transparent, no-pressure for individual designing ), & flexible, optical adaptation to ambient is also possible. Delivery without 50-mm-Adapter frames ...

The FS20 IRP simplifies a programming & a configuration of the FS20 systems completely substantially. It extends besides the functional range of selected transmitters of the FS20 program All configuration of the transmitters (addressing, command assignment, switching-on or dimming time, channel assignment, etc.) are to be clearly set & can documented via the provided Windows software in addition for every key of the transmitter, macros with up to 3 actions can be stored
- so far that was not possible on the normal programming of the! The finished configurations can be stored on the PC & released by USB (Universal Serial Bus) to the FS20 IRP This is then released by infrared on the FS20 transmitter
...

The FS20 FMS radio-controls any FS20 switch actors such as the FS20 ST radio socket or the surface-mounted FS20 AS4 4-channel switch as soon as the main equipment connected to it is switched on or off. This permits having the garden or house lighting switched on as soon as the garage door is opened, for instance. A timer function can be used to switch off the consumers automatically.
You can also use it the opposite way round, e.g. to tell you when the washing machine has finished. In this case the FS20 FMS signals that the washing machine has finished & sends a switch command to the FS20 SIG radio transmitter, for instance. Here the timer can be programmed to delay the transmitter signal so that the transmitter only transmits after the programmed delay. For appliances that consume power when they are switched off (st&-by), you can set the response threshold of the FS20 FMS in several increments. As a real FS20 device, the FS20 FMS can be integrated into the FS20 code & address system.
...

With the radio repeater RPT FS20 you can increase the range of the transmitter of your wireless switching system FS20. To allow an easy access even in adverse conditions, such as radio massive steel reinforcement in concrete ceilings reliable Radio-switch-signal transmission. Since the signals can be repeated up to twice, you can reach 3 times the transmitter range with 2 repeaters. The repeater is suitable for transmitting dimming commands only to a certain extent. Thanks to the practical design that fits into the plug housing, the power supply to the repeater is extremely easy, & the existing socket can still be used because the mains voltage is switched through. ...

Using programmable roller shutter control, it is possible to realise a visually unnoticed radio controlling of electric-driven roller shutters, awnings & venetian blinds. Roller shutter switch can be operated though compact flush-mounted housing & all FS20-centres are controlled through the sender of FS20-system & also through direct key. In addition to manual & time- or event-driven switching function, a programmable timer function is available to adjust runtime of the actuator. ...

On this compact hand transmitter there are 8 buttons for various control functions. This means you can dim & switch on & off 4 wireless receivers, independently of the FHZ 1000 wireless home system. Naturally you can also use this remote control for addressing & timer programming the receivers. ...