Trend SL/GG Slotter 4.0mm Kerf 1/4 Bore

Features: All slotters are precision made in TCT grade for long life

...

Trend SM/BP Scribemaster Pro Carry Case Hard wearing carry case to protect & allow for ease of carrying of the Scribemaster Pro Scribing Jig. To fit into the case the feet of the jig will need to be removed.

Features: Padded nylon weave material for maximum protection Case has a zip closure to keep contents secure

...

Trend SM/MKP Scribemaster Pro Quick Mount Kit Chop saw stand mounting kit for the Scribemaster Pro. The bench mount kit is designed to work with a variety of mitre saw stands when fitted with mounting brackets. Comes With: 4 x Stepped bush 4 x Coach bolt M8 8 x Nut M8   Weight: 0.5kg ...

Trend SM/PRO Scribe Master Pro Scribing Jig The Trend Scribe Master Pro is perfect for fast, efficient & accurate scribes every time. Designed & made in the UK with a patented design, it will quickly mount on to your mitre saw stand with the optional mount kit or can be used stand alone. How it works: Steel combs are pushed in to the sample mould Comb assembly is then turned over to give a scribe Copy pin then follows the scribecontour allowing the router cuttern to cut the scribe

Features: Can cut any skirting or dado profile Cuts left & right hand scribes Scribes warped boards For use with 1/4" or 1/2" routers Up to 10 times faster than manual scribes Quick & easy to set up & use Pre assembled & ready for use Precisie cuts every time Made from High Pressure Laminate for stability Comes with: 4mm x 1/4" shank HSSE single flute spiral for softwood & MDF Comb alignment tool Workpiece clamp knob

...

Trend SM/TSP Scribemaster Pro Tenon Slide Plate Tenon slide plate for use with the Scribemaster Pro. Used to cut through housing, half lap & tongue & groove lining joints.

Features: Plate is locked in position on jig & allows through housing, half lap (halving) & tongue & groove lining joints etc. to be routed. Use with a 30mm guide bush & suitable straight cutter. Maximum cutter diameter 22mm. Comes with: 1 x Tenon plate 1 x Clamp bar 1 x Hex key 4mm / 5mm   Max. working length: 190 mm Max. tenon length adj: 50 mm Max. cutter dia: 22 mm

...

Trend SMC/03 Scribemaster Pro Cutter 4 x 40 x 90mm x 8mm Shank HSS Accessory cutter for use with the Scribemaster Pro. Made from a single piece of High Speed Steel, ground with a very fine edge. Suitable for non-abrasive natural timbers & plastics. Will give a superior finish in soft timbers.

Features: For hardwood. Two flute down cut spiral for clean finish. Made from Super High Speed Steel that allows flute to be ground to a very fine cutting edge. Cutting Diameter: 4 mm Cutting Length: 40 mm Overall Length: 90 mm Shank Diameter: 8 mm Weight: 0.1kg

...

Trend SNAP/ASA/2 Trend Snappy Angle Screwdriver Attachment Mark 2 (Shank Diameter 1/4 Hex)

Features: 90 degree

...

Trend SNAP/BH/11 Trend Snappy 25mm Bit Holder 279mm (11 Inch) (Shank Diameter 1/4 Hex")

Features: Extra

...

Trend SNAP/BH/58 Trend Snappy 25mm Bit Holder 58mm (Shank Diameter 1/4 Hex")

Features: Magnetic holder

...

Trend SNAP/BH/6 Trend Snappy 25mm Bit Holder 152mm (6 Inch) (Shank Diameter 1/4 Hex")

Features: Extra long

...