The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers In addition the extremely quiet 120mm fan with a fined-tuned RPM curve has been optimized for airflow This makes the Modular Power the quietest power supply of its kind The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible flat & semi-modular cables use for connections across the system THE KOLINK MODULAR POWER 500W POWER SUPPLY AT A GLANCE444W & 37A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Semi-modular cable management modern look with flat black cables Connectors 1x 24-pin 1x 44-pin 2x 62-pin 4x SATA 2x Molex KOLINK MODULAR POWER FULL PERFORMANCE & HIGH EFFICIENCYThe 500 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment The PSU delivers up to 444W & 37A on the 12V rail while providing 100W & 15A each on the 33V & 5V rails This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 858282 percent at 5020100 percent load (at 230 Volt input voltage) The PSU's highly efficient circuit design features independent DC-to-DC converters for the 33V & 5V outputs ensuring extremely precise voltage regulation Each example of Modular Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve Thanks to the optimized airflow the fan & thus the entire PSU remain quiet as a whisper Besides the 204 pin for the motherboard the Kolink Modular Power has a 44 pin connector for the CPU & two 62 pin connectors for dedicated graphics cards Four SATA & two Molex connectors are available for additional components The flat flexible completely & semi-modular black cables have a modern look & fit into almost any up-to-date gaming setup Note For environmental reasons the manufacturer does not supply a power cord for connection to the mains Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic control) Colour Black (power supply fan) Efficiency minimum 858282 percent at 5020100 percent load Fulfils requirements for 80 PLUS Bronze certification Active PFCForm Factor ATX12V 24EPS12V 292 Performance 500 W33V 15 A5V 15 A33V &38; 5V combined 100 W12V 444 W 37 A-12V 3 W 03 A5 Vsb 125 W 25 AConnectors (semi-modular) Motherboard 1x 204-Pin ATX12VEPS12V (500 mm fixed)CPU 1x 44-Pin ATX12VEPS12V (600 mm fixed)1x 2 62-Pin PCIe (600 100 mm modular)1x 4 SATA (500 100 100 100 mm modular)1x 2 4-Pin Molex (500 100 mm modular) Protective Circuits OVPUVP (Over- & undervoltage protection)SCP (short circuit) OPP (overload) OCP (overcurrent on rails 12 33 & 5 Volt)MTBF 100000 h Manufacturer's guarantee 3 Years ...

The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers In addition the extremely quiet 120mm fan with a fined-tuned RPM curve has been optimized for airflow This makes the Modular Power the quietest power supply of its kind The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible flat & semi-modular cables use for connections across the system THE KOLINK MODULAR POWER 600W POWER SUPPLY AT A GLANCE546W & 455A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Semi-modular cable management modern look with flat black cables Connectors 1x 24-pin 1x 44-pin 2x 62-pin 4x SATA 2x Molex KOLINK MODULAR POWER FULL PERFORMANCE & HIGH EFFICIENCYThe 600 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment The PSU delivers up to 546W & 455A on the 12V rail while providing 100W & 15A each on the 33V & 5V rails This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 858282 percent at 5020100 percent load (at 230 Volt input voltage) The PSU's highly efficient circuit design features independent DC-to-DC converters for the 33V & 5V outputs ensuring extremely precise voltage regulation Each example of Modular Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve Thanks to the optimized airflow the fan & thus the entire PSU remain quiet as a whisper Besides the 204 pin for the motherboard the Kolink Modular Power has a 44 pin connector for the CPU & two 62 pin connectors for dedicated graphics cards Four SATA & two Molex connectors are available for additional components The flat flexible completely black & semi-modular cables have a modern look & fit into almost any up-to-date gaming setup Note For environmental reasons the manufacturer does not supply a power cord for connection to the mains Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic control) Colour Black (power supply fan) Efficiency minimum 858282 percent at 5020100 percent load Fulfils requirements for 80 PLUS Bronze certification Active PFCForm Factor ATX12V 24EPS12V 292 Performance 600 W33V 15 A5V 15 A33V &38; 5V combined 100 W12V 546 W 455 A-12V 3 W 03 A5 Vsb 125 W 25 AConnectors (semi-modular) Motherboard 1x 204-Pin ATX12VEPS12V (500 mm fixed)CPU 1x 44-Pin ATX12VEPS12V (600 mm fixed)1x 2 62-Pin PCIe (600 100 mm modular)1x 4 SATA (500 100 100 100 mm modular)1x 2 4-Pin Molex (500 100 mm modular) Protective Circuits OVPUVP (Over- & undervoltage protection)SCP (short circuit) OPP (overload) OCP (overcurrent on rails 12 33 & 5 Volt)MTBF 100000 h Manufacturer's guarantee 3 Years ...

The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers In addition the extremely quiet 120mm fan with a fined-tuned RPM curve has been optimized for airflow This makes the Modular Power the quietest power supply of its kind The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible & flat cables use for connections across the system THE KOLINK MODULAR POWER 700W POWER SUPPLY AT A GLANCE648W & 54A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Modern look with flat black cables Connectors 1x 24-pin 1x 44-pin 4x 62-pin 6x SATA &38; 2x Molex KOLINK MODULAR POWER FULL PERFORMANCE & HIGH EFFICIENCYThe 700 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment The PSU delivers up to 648W & 54A on the 12V rail while providing 110W & 15A each on the 33V & 5V rails This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 858282 percent at 5020100 percent load (at 230 Volt input voltage) The PSU's highly efficient circuit design features independent DC-to-DC converters for the 33V & 5V outputs ensuring extremely precise voltage regulation Each example of Modular-Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve Thanks to the optimized airflow the fan & thus the entire PSU remain quiet as a whisper Besides the 204 pin for the motherboard the Kolink Modular Power has a 44 pin connector for the CPU & four 62 pin connectors for dedicated graphics cards Six SATA & two Molex connectors are available for additional components The flat flexible & completely black cables have a modern look & fit into almost any up-to-date gaming setup Note For environmental reasons the manufacturer does not supply a power cord for connection to the mains Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic control) Colour Black (power supply fan) Efficiency minimum 858282 percent at 5020100 percent load Fulfils requirements for 80 PLUS Bronze certification Active PFCForm Factor ATX12V 24EPS12V 292 Performance 700 W33V 15 A5V 15 A33V &38; 5V combined 110 W12V 648 W 54 A-12V 3 W 03 A5 Vsb 125 W 25 AConnectors (semi-modular) Motherboard 1x 204-Pin ATX12VEPS12V (500 mm fixed)CPU 1x 44-Pin ATX12VEPS12V (600 mm fixed)1x 2 62-Pin PCIe (600 100 mm fixed)1x 2 62-Pin PCIe (600 100 mm modular)2x 3 SATA (500 100 100 mm modular)1x 2 Molex (500 100 mm modular) Protective Circuits OVPUVP (Over- & undervoltage protection)SCP (short circuit) OPP (overload) OCP (overcurrent on rails 12 33 & 5 Volt)MTBF 100000 h Manufacturer's guarantee 3 Years ...

Cutting a striking figure amongst the highly competitive ATX-format segment the Nimbus Midi-Tower from Kolink offers an ARGB-LED strip rounding the large cut-out in the front
- enabling a significant improvement in airflow The hardware installed inside the case will also remain clear of dust thanks to the filter which is important as users will also enjoy the opportunity to admire their hard-earned hardware through the tempered glass side In spite of Kolink's use of solid tempered glass the Kolink Nimbus still weighs only 458kg The generous

Dimensions of the case not only help with airflow they also allow users to install motherboards up to ATX in form factor Graphics cards up to 325 mm long are compatible
- meaning that the case is perfect for housing some seriously high-end gaming hardware THE FEATURES OF THE KOLINK NIMBUS MIDI-TOWER AT A GLANCEDesigner case in black for motherboards up to ATXLarge air inlet in the front with ARGB-LED surround for better airflow Magnetic dust filters on the front roof & bottom 4 mm thick tempered glass side panel 1x Pre-installed 120 mm fan 6 possible in total IO Panel with 2x USB (Universal Serial Bus) 20 1x USB (Universal Serial Bus) 30 &38; HD Audio In Out RGB-LED controller Support for radiators up to 240 mm in front & roof 2x 3525 drive slots 2x slots for 25 drives on motherboard tray Supports graphics cards up to 325 cm long &38; CPU coolers up to 16 cm TEMPERED GLASS SIDE PANEL &38; PRE-INSTALLED FANThe robust chassis consists of one millimetre thick SECC steel &

Includes:: a four millimetre thick tempered glass side panel with an aluminium-look plastic front A large cut-out in the front has a digitally addressable RGB-LED strip included which can be both synced to compatible 3-Pin motherboards & controlled on the front panel The magnetic dust filter located behind it helps keep the interior clean & dust free & allows for sufficient airflow The interior has a black coating & utilises a power supply shroud to help maintain a clean aesthetic Beneath this users will find a non-removable drive cage with brackets for two 35- or 25 drives as well as space for the power supply itself Two additional slots for 25 drives are located to the rear of the motherboard tray DUST FILTERS KEEP THE KOLINK NIMBUS CLEANIn order to keep your gaming hardware supplied with a continuous stream of cool fresh air
- one (of a possible total of six) 120 mm fan in black is included with the case & installed in the rear The front of the case supports up to three 120 mm fans the roof of the case allows for two further 120 mm fans The front of the case supports two 140 mm fans A 240 mm radiator can be installed in the front & the roof The motherboard tray & the PSU cover include various openings for all the cable management options you could ask for The air inlets located in the roof & underside of the case also include a fine mesh These are magnetic & utilise a honeycomb-structure design to add strength Graphics cards up to 325 cm with CPU coolers up to 16 cm are both supported in addition the IO panel located on the front of the case

Includes:: two USB (Universal Serial Bus) 20 ports along with a USB (Universal Serial Bus) 30 Type-A port A switch for controlling the RGB lighting is also available Technical Details Dimensions 210 x 440 x 370 mm (W x H x D) Material Steel tempered glass plastic Weight approx 458kg Colour Black Form factor ATX Micro-ATX Mini-ITXTotal possible fans 3x 120 mm (Front)2x 120 mm (roof)1x 120 mm (rear) Pre-installed 1x 120 mm (rear 3-Pin) Radiator Mountings 1x 240 mm (front)1x 240 mm (roof) Filter Roof underside Drive Bays 2x 3525 (internal)2x 25 (internal reverse of motherboard tray PSU 1x Standard ATX to 180 mm (optional) Expansion Slots 7IO Panel 2x USB (Universal Serial Bus) 20 (internal connection)1x USB (Universal Serial Bus) 30 (internal connection)1x Audio In Out 1x RGB-LED Control Max GPU length 325 mm Max CPU cooler height 160 mm Max PSU length 180 mm








...

Kolink is pleased to introduce the incredibly stylish Observatory Midi-Tower with its fantastic tempered glass side panel & transparent front The inclusion of a total of four pre-installed RGB-LED fans allows the case to unlock its full cooling potential The lighting can also be controlled via the included controller & remote control The Observatory&s spacious interior offers capacity for a wide range of hardware & components Some of the highlights of this case include pre-installed dust filters extensive space for watercooling as well as practical cable management options These are just some of the strong points of this case & all that in spite of the extremely competitive price point TEMPERED GLASS SIDEFRONT PANEL & FOUR PRE-INSTALLED RGB FANSThe robust chassis consists of one millimetre strong SECC steel & is equipped with a four millimetre thick tempered glass side & front panel The interior interior has a black coating & is also kitted out with a shroud for the power supply to ensure an incredible clean look There is also a hard drive cage with brackets for two 35- or 25-" drives The visual highlights of the case include three 120 mm fans pre-installed in the front & an additional fan in the back The fans come with 16 individually addressable RGB-LEDs Their lighting can be controlled by the bundled RGB controller & fan hub which can be placed in a location of your choosing as well as the infrared remote control This means that you can choose from over 300 dynamic lighting effects! Two further 120 mm fans can be mounted in the top DUST FILTERS KEEP THE KOLINK OBSERVATORY CLEANThe motherboard tray & the power supply shroud offer numerous cable openings A 240 mm radiator can be installed in the front & the top of the Observatory case The case&s air vents come equipped with fine dust filters that are located in the top & underside of the case These can be removed without the need for tools & even come complete with a smart honeycomb design Graphics cards up to 38 cm long & CPU coolers up to 16 cm high are compatible Furthermore the IO panel located on the front also comes with two further USB (Universal Serial Bus) 20 connectors as well as a USB (Universal Serial Bus) 30 Type A port There is also a slot for a USB (Universal Serial Bus) Type C connection but this is not included in the case & must be retrofitted separately The same applies to a switch for controlling the RGB lighting on the IO panel Features- Case designed for motherboards up to E-ATX- 4 mm tempered glass side & front panel- 4x 120 mm RGB fans including controller & remote- IO panel with 2x USB (Universal Serial Bus) 20 1x USB (Universal Serial Bus) 30 & HD Audio In Out- Support for two 240 mm radiators- 2x 3525" drive slots- Graphics cards up to 38 cm long & CPU coolers up to 16 cm in height Form Factor Full Tower Motherboard Support E-ATX (up to 279 mm wide)ATXMicro ATXMini-ITXMaterials Steel Tempered Glass IO Ports 2 x USB (Universal Serial Bus) 20 (internal connection)1 x USB (Universal Serial Bus) 30 (internal connection)1 x Audio In Out Drive Bays 2 x 3525" (internal) Expansion Slots 7 Pre-Installed Fans Front 3 x 120 mm RGBRear 1 x 120 mm RGBFan Options Front 3 x 120 mm Top 2 x 120 mm Rear 1 x 120 mm Radiator Mountings Front 1 x 240 mm Top 1 x 240 mm PSU Included No PSU Mountings 1 x Standard ATX up to 200 mm Clearance Maximum GPU Length 380 mm Maximum CPU Cooler Height 160 mm Dust Filters Top Underneath Colour Black Dimensions (W x H x D )201 x 435 x 435 mm Weight 68kg ...

Kolink is pleased to introduce the incredibly stylish Observatory Midi-Tower with its tempered glass front- & side panel through which users can see the total of four pre-installed RGB-LED fans in all their glory The lighting can be controlled via the bundled controller & remote The tidy interior of the Observatory offers lots of space for putting your hardware on show Pre-installed dust filters extensive space for water cooling & cable management these are just a few of the highlights offered by this Kolink case despite its diminutive size & price This case is almost entirely white except for the black elements & this helps it look extremely premium for the price THE FEATURES OF THE KOLINK OBSERVATORY AT A GLANCECase designed to support motherboards up to E-ATXFront & side panel in 4 mm thick tempered glass 4x 120 mm RGB fans including controller & remote IO Panel with 2x USB (Universal Serial Bus) 20 1x USB (Universal Serial Bus) 30 &38; HD Audio In Out Support for two radiators in 280 mm format 2x 35 & 4x 25 data storage devices Supports graphics cards up to 38 cm long &38; CPU coolers up to 16 cm high FRONT & SIDE PANEL IN TEMPERED GLASS &38; FOUR PRE-INSTALLED RGB FANSThe robust chassis is made from millimetre thick SECC steel & comes with a front & side panel in four millimetre thick glass The entire interior is likewise coated in white & equipped with a shroud for the power supply in order to maintain an incredibly clean aesthetic A hard drive cage is attached here with brackets for two 35 drives as well as space for the power supply Four more 25 drives can be placed next to the motherboard The visual highlight of the case is formed by the three 120 mm RGB fans pre-installed in the front & an additional fan in the rear The fans possess 16 individually addressable RGB-LEDs Their lighting can be controlled via infrared remote control using the bundled RGB controller & fan hub that can be placed in a location of your choosing This enables 300 dynamic lighting effects to be configured Two further 120 mm or 140 mm fans can be mounted in the roof The three 120 mm fans at the front can be exchanged for two 140 mm fans DUST FILTERS KEEP THE KOLINK OBSERVATORY CLEANThe motherboard tray & the PSU shroud offer multiple openings for cables A 240 mm or 280 mm radiator can be installed in the front & on the roof of the Kolink case With air inlets are equipped with fine dust filters located in the roof & on the bottom of the case They are easily removed without requiring tools & strengthened with a filigree honeycomb design GPUs can be up to 38 cm long & CPU coolers may be up to 16 cm high in addition the IO panel located on the front offers two USB (Universal Serial Bus) 20 connections as well as a USB (Universal Serial Bus) 30 Type-A port A cut-out is present for a USB (Universal Serial Bus) Type-C connection however this does not come as standard with the case & must be added later The same is true of a switch used for controlling the IO panel's RGB lighting Technical Details Dimensions 210 x 435 x 435 mm (W x H x D with standups) Dimensions 210 x 453 x 435 mm (W x H x D without standups) Material Steel tempered glass Weight approx 68kg Colour White (case) Black (mesh elements) Form Factor E-ATX (up to 279 mm wide) ATX Micro-ATX Mini-ITXTotal Possible Fans 3x 120 mm 2x 140 mm (Front)2x 120 mm 140 mm (Top)1x 120 mm (Rear) Pre-Installed 3x 120 mm RGB (Front)1x 120 mm RGB (Rear) Radiator Mountings 1x 240 mm 280 mm (Front)1x 240 mm 280 mm (Roof) Filter Roof underside Drive Bays 4x 25 (internal)2x 35 (internal) Power Supply 1x Standard ATX up to 200 mm (optional) Expansion Slots 7IO Panel 2x USB (Universal Serial Bus) 20 (internal connection)1x USB (Universal Serial Bus) 30 (internal connection)1x Audio In Out Maximum GPU Length 380 mm Maximum CPU Cooler Height 160 mm ...

With their premium & yet affordable gaming cases Kolink has firmly established themselves as a leader in the world of respected case manufacturers The Outline represents an impressive addition to their category of high-performance cases one that manages to offer as much in terms of design as it does in functionality The spacious interior fits up to a high-end SSI-EEB motherboard & graphics cards up to 360 mm in length The cards can also be installed vertically providing they are dual slot width using the supplied mount & a PCI-E riser cable (sold separately) It goes without saying that the case offers plenty of room for all your cooling needs the front supports a radiator up to 360 mm & the roof supports a 240 mm radiator What really stands out however is the design of its front panel on the left are functional but attractive air inlets in a checkerboard pattern on the right is a digitally addressable RGB-LED strip in the form of a narrow rectangle A pre-installed high-performance 120 mm ARGB fan illuminates the interior of this deceptively large Midi-Tower meaning that excellent cooling is a given A tempered glass side panel allows users to enjoy an unobstructed view of the installed hardware THE FEATURES OF THE KOLINK OUTLINE MIDI-TOWER AT A GLANCEStylish Midi-Tower for motherboards up to SSI-EEB format Tempered glass side panel for a clear view of the interior Digitally addressable RGB-LED strip on the front Option of vertically mounting a dual slot GPURadiator up to 360 mm on the front up to 240 mm on the roof A pre-installed 120mm fan on the back with digitally addressable RGB-LEDs Up to six 120 mm fans supported Space for graphics cards up to 360 mm CPU coolers up to 162 mm IO Panel with controller for RGB-LEDs 1x USB (Universal Serial Bus) 30 2x USB (Universal Serial Bus) 20 & HD Audio PLENTY OF SPACE FOR GAMING HARDWARE IN THE KOLINK OUTLINEEven if the outside of the case corresponds to the

Dimensions of a Midi-Tower the Kolink Outline manages to provide support for motherboards up to the SSI-EEB format Even graphics cards up to 360 mm will fit thanks to the amount of room available behind the front panel Even large CPU coolers up to 162 mm in height will fit with ease A shroud helpfully conceals the power supply & the HDD cage in which users can either install two 35- or two 25 drives The rear of the motherboard allows for two 25 SSDs to be installed Those preferring to opt for air cooling will appreciate the number of mounting points present for 120 mm fans The roof supports two 120 mm fans It is also equipped with a handy mesh which allows air to flow through the case without excess dust thanks to the presence of a dust filter The result is that this is a large attractive yet low-maintenance case If that's still not enough cooling the front supports up to three 120 mm fans The slot at the rear is occupied by a 120 mm fan The pre-installed fan is equipped with digitally addressable RGB-LED lighting Of course users are free to install radiators instead of fans if needed with a 240 mm radiator in the roof & a 360 mm at the front TEMPERED GLASS & RGB-LEDS TO PUT YOUR HARDWARE ON SHOWThe power supply cover provides a tidy look inside the case Well-placed feedthroughs & cable guides allow for sophisticated cable management The eye-catching strip on the front of the case is equipped with digitally addressable RGB LEDs the lighting of which can be controlled via a switch on the IO panel or the strip can be connected directly to a motherboard & controlled directly via the board instead The lighting on the pre-installed fan is also done via a compatible 3-pin connector (5VDG) which can also be controlled via the controller on the IO panel or via the motherboard The RGB switch on the IO panel can also double up as a reset button In addition to the RGBReset switch there are one USB (Universal Serial Bus) 30 & two USB (Universal Serial Bus) 20 slots as well as 35 millimetre sockets for headphones & microphone a power LED & an HDD LEDTechnical details Dimensions (H x W x D) 415 x 210 x 440 mm Material Steel tempered glass plastic Weight approx 59kg Colour Black Form Factor SSI-EEB E-ATX ATX Micro-ATX Mini-ITXFan possible in total 2x 120 mm (cover)3x 120 mm (front side)1x 120 mm (rear) Pre-installed 1x 120 mm Rear side Radiator mountings 1x 240 mm (cover)1x 360 mm (front side)1x 120 mm (rear) Filter cover underside Drive bays 2x 3525 inch (internal HDD cage) Power supply 1x standard ATX (optional) Extension slots 72IO Panel 2x USB (Universal Serial Bus) 20 (internal connection)1x USB (Universal Serial Bus) 30 (internal connection)1x per Audio In Out 1x RGBReset switch Maximum graphics card length 360 mm Vertical GPU Support Dual Slot up to 360mm PCI-E Riser cable sold separately Maximum CPU cooler height 162 mm Maximum power supply length 180 mm

...

This PCI Express x 1 to x 16 powered riser card with an additional Molex power connector is the ideal accessory for Bitcoin Mining systems & of course taking into account the available bandwidth Can also be used like any other riser card for other systems & applications such as Altcoin Ethereum Ether Zcash Distributed Computing Rendering & Boinc Bitcoin is a virtual pay-as-you-go virtual payment tool launched & managed by all the participating Bitcoin network clients Like many other cryptos with proof-of-work principle bitcoins are caused by computer Cryptographic computing tasks with a high energy expenditure which is called "mining" (mining) In principle normal computer processors (CPUs) are capable of calculating new bitcoins but they can only calculate a few (kilo) hashes per second & therefore are not suited to bitcoin mines in relation to the time & energy used for this purpose Regarding the efficiency they are clearly beaten by graphics processors (GPUs) especially graphics chips of the Radeon series from AMD have proved particularly strong Mining rigs are referred to as PC-systems from commercially available hardware components the only task of which is to calculate Bitcoins by means of several graphics cards in continuous operation In order to counter the resulting high heat development & to operate as many graphics cards as possible in parallel these GPU-Miner systems usually use very open housings (comparable to Benchtables) or in some cases adventurous self-assembled case circuits As with AMD Cross Fire or NVIDIA SLI gaming PCs not all PCI Express slots can be used on a system-based motherboard since high-performance graphics cards generally have a wide dual fan or even three-fan fan & thus the space required for further GPUs is missing or must be moved with many Mining PCs all PCIe slots due to the respective graphics card constellation This is where the practical powered Riser Card comes in & allows the installation of PCI Express slots with x 1 x 4 x 8 or x 16 connectivity on the motherboard by allowing an additional PCI Express x 16 slot to be strategic In or outside the housing This x 16 slot is electrically connected to a single PCI Express lane which corresponds to the PCIe generation of the output slot Since bitcoin mining is only performed by the GPU & in contrast to video games no textures or shader data have to be transported into the graphics memory the bandwidth available for this application is sufficient For data transfer the riser card is a USB (Universal Serial Bus) 30 cable With a length of Approx. 600 millimeters allows a lot of room for the PCIe slot In contrast to the often used IDE flat-ribbon cables with conventional riser cards the module can be installed better & there are further advantages in the higher stability as well as the less hindrance of the airflow A SATA-to-Molex power cable which is also included transmits up to 75 watts of electrical power directly from the power supply which is normally delivered directly from the PCIe slot while the additional energy of the graphics card comes directly from the power supply via additional PCIe plugs With this powered riser it is thus possible to operate up to 6 graphics cards on a mainboard without overloading its voltage supply 600 millimeters allows a lot of room for the installation of the PCIe slot In contrast to the often used IDE flat-ribbon cables with conventional riser cards the module can be installed better & there are further advantages in the higher stability as well as the less hindrance of the airflow A SATA-to-Molex power cable which is also included transmits up to 75 watts of electrical power directly from the power supply which is normally delivered directly from the PCIe slot while the additional energy of the graphics card comes as usual via additional PCIe plugs directly from the power supply With this powered riser it is thus possible to operate up to 6 graphics cards on a mainboard without overloading its voltage supply In contrast to the often used IDE flat-ribbon cables with conventional riser cards the module can be installed better & there are further advantages in the higher stability as well as the less hindrance of the airflow A SATA-to-Molex power cable which is also included transmits up to 75 watts of electrical power directly from the power supply which is normally delivered directly from the PCIe slot while the additional energy of the graphics card comes as usual via additional PCIe plugs directly from the power supply With this powered riser it is thus possible to operate up to 6 graphics cards on a mainboard without overloading its voltage supply A SATA-to-Molex power cable which is also included transmits up to 75 watts of electrical power directly from the power supply which is normally delivered directly from the PCIe slot while the additional energy of the graphics card comes directly from the power supply via additional PCIe plugs With this powered riser it is thus possible to operate up to 6 graphics cards on a mainboard without overloading its voltage supply Up to 6 graphics cards on a mainboard without overloading the power supply Cable length approx 60 cm Connections Plug-in module PCIe with 1 lane socket module PCIe with 16 lanes (electrical connection x 1) Power supply 1x 4-pin Molex socket Supplied cables 1x USB (Universal Serial Bus) 30 1x SATA to Molex adapter cable Supported PCI Express standards 1x 2x 30 ...

This PCI-Express x 1 to x 16 powered riser card with additional 6-pin PCIe power connector is the ideal accessory for bitcoin mining systems & can of course be used in accordance with the requirements set out here As well as any other riser card for other systems & application areas such as Altcoin Ethereum Ether Zcash Distributed Computing Rendering & Boinc Bitcoin is a virtual pay-as-you-go virtual payment tool launched & managed by all the participating Bitcoin network clients Like many other cryptos with proof-of-work principle bitcoins are caused by computer- Cryptographic computing tasks with a high energy expenditure which is called "mining" (mining) In principle normal computer processors (CPUs) are capable of calculating new bitcoins but they can only calculate a few (kilo) hashes per second & therefore are not suited to bitcoin mines in relation to the time & energy used for this purpose Regarding the efficiency they are clearly beaten by graphics processors (GPUs) especially graphics chips of the Radeon series from AMD have proved particularly strong Mining rigs are referred to as PC-systems from commercially available hardware components the only task of which is to calculate Bitcoins by means of several graphics cards in continuous operation In order to counter the resulting high heat development & to operate as many graphics cards as possible in parallel these GPU-Miner systems usually use very open housings (comparable to Benchtables) or in some cases adventurous self-assembled case circuits As with AMD Cross Fire or NVIDIA SLI gaming PCs not all PCI Express slots can be used on a system-based motherboard since high-performance graphics cards generally have a wide dual fan or even three-fan fan & thus the space required for further GPUs is missing or must be moved with many Mining PCs all PCIe slots due to the respective graphics card constellation This is where the practical powered Riser Card comes in & allows the installation of PCI Express slots with x 1 x 4 x 8 or x 16 connectivity on the motherboard by allowing an additional PCI Express x 16 slot to be strategic In or outside the housing This x 16 slot is electrically connected to a single PCI Express lane which corresponds to the PCIe generation of the output slot Since bitcoin mining is only performed by the GPU & in contrast to video games no textures or shader data have to be transported into the graphics memory the bandwidth available for this application is sufficient For data transfer the riser card is a USB (Universal Serial Bus) 30 cable With a length of Approx. 800 millimeters allows a great deal of room for the installation of the PCIe slot In contrast to the often used IDE flat-ribbon cables with conventional riser cards the module can be installed better & there are further advantages in the higher stability as well as the less hindrance of the airflow The power supply to the board is provided by a 6-pin PCI Express connector directly from the power supply which is capable of providing up to 75 watts of electrical power normally supplied by the motherboard&s PCIe slot Compared to Molex plugs & adapters this type of power supply ensures a lower transition resistance & is therefore particularly stable & extremely reliable The remaining energy required by the graphics card comes as usual from other PCIe connectors directly connected to the GPU With this powered riser it is thus possible to operate up to 6 graphics cards on a mainboard without overloading the power supply or the cables of the power supply Technical details Cable length approx 80 cm Connections Plug-in module PCIe with 1 lanesocket module PCIe with 16 lanes (electrical connection x 1) Power supply 1x 6-pin PCI Express socket Supplied cables 1x USB (Universal Serial Bus) 30 Supported PCI Express standards 1x 2x 30 ...

This riser cable from the case specialists at Kolink allows the PCI-Express x 16 slot on the motherboard to interface with a graphics card in a vertical orientation The Kolink PCI Express 30 x 16 to x 16 riser cable is Approx. 200 mm long Due to its exceptional manufacturing quality & design it is suitable for use in cases from all manufacturers Technical Details Length 200 mm Colour Black Ports Connector PCIe with 16 Lanes Interface PCIe with 16 Lanes Supported PCI-Express Standards 1x 2x 30 ...