The Enclave Series from Kolink represents a new series of high-performance power supplies with 80 PLUS Gold certification The premium quality components advance design & powerful 12V single-rail ensure robust & reliable power delivery as well as precise voltage regulation The premium quality power supply is rounded off by the welcome addition of fully modular cable management as well as a whisper-quiet 120 mm fan THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATES FOR 500 WATTS AT A GLANCE500 Watt PSU with powerful 41A single rail High efficiency thanks to 80 PLUS Gold certification Quiet 120 mm fan Fully modular cable management with flat cables Two 6-Pin PCIe connectors for graphics cards Five SATA- & four Molex connectors THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATES AT 500 WATTS IN DETAILThe advanced design & the use of high-quality components mean that Kolink has been able to produce an efficient & high-performance power supply in the form of the Enclave 80 PLUS Gold 500W To this end the manufacturer has opted for LLC transformers & DC-DC technology alongside independent voltage regulation This combination also provides benefits to the unit's operating efficiency as well as the precision with which voltages are regulated particularly when it comes to asymmetric loads As a result the Enclave is capable of outputting nearly its entire rated power delivery through the 12 Volt rail if necessary This can be up to 41A & means that all your high-performance components are kept well-supplied with all the power they need The high operating effectiveness means that it meets the criteria for 80 PLUS Gold certification as well as an average efficiency of 92 percent when used on a European 230 Volt network In terms of cooling the units use a slow-spinning 120 mm fan with ultra-durable rifle bearings Apart from the impressive performance specifications the Kolink Enclave 500W isn't short of connectivity options either in addition to a 204-Pin ATX- & a 44-Pin 12V EPS connector there are also two 6-Pin PCIe connectors available to supply graphics cards with power Additional components are powered by means of five SATA- & four Molex connectors Note For environmental reasons the manufacturer does not supply a wall outlet power cable with the unit Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic regulation rifle-bearing fan) Colour Black (PSU fan) Efficiency min 908787 percent at 5020100 percent load on European 230 Volt network Meets requirements for 80 PLUS Gold Active PFCForm factor ATX 12V V231 Output 500 W33V 16 A5V 16 A33V & 5V combined 100 W12V 492 W 41 A-12V 6 W 05 A5 Vsb 15 W 3 AConnectors (removable)1x 204-Pin ATX12VEPS12V1x 44-Pin ATX12VEPS12V2x 6-Pin PCIe 5x SATA4x 4-Pin Molex Safety OVPUVP (protection against over- & undervoltage)SCP (short circuit)OPP (overload)OCP (over-current protection on 12 33 & 5 Volt rails) Manufacturer's guarantee 3 Years ...

The Enclave Series from Kolink represents a new series of high-performance power supplies with 80 PLUS Gold certification The premium quality components advance design & powerful 12V single-rail ensure robust & reliable power delivery as well as precise voltage regulation The premium quality power supply is rounded off by the welcome addition of fully modular cable management as well as a whisper-quiet 120 mm fan THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATED FOR 600 WATTS AT A GLANCE600 Watt PSU with powerful 48A single rail High efficiency thanks to 80 PLUS Gold certification Quiet 120 mm fan Fully modular cable management with flat cables Four 62-Pin PCIe connectors for graphics cards Eight SATA- & four Molex connectors THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATED AT 600 WATTS IN DETAILThe advanced design & the use of high-quality components mean that Kolink has been able to produce an efficient & high-performance power supply in the form of the Enclave 80 PLUS Gold 600W To this end the manufacturer has opted for LLC transformers & DC-DC technology alongside independent voltage regulation This combination also provides benefits to the unit's operating efficiency as well as the precision with which voltages are regulated particularly when it comes to asymmetric loads As a result the Enclave is capable of outputting nearly its entire rated power delivery through the 12 Volt rail if necessary This can be up to 48A & means that all your high-performance components are kept well-supplied with all the power they need The high operating effectiveness means that it meets the criteria for 80 PLUS Gold certification as well as an average efficiency of 92 percent when used on a European 230 Volt network In terms of cooling the units use a slow-spinning 120 mm fan with ultra-durable rifle bearings Apart from the impressive performance specifications the Kolink Enclave 600W isn't short of connectivity options either in addition to a 204-Pin ATX- & a 44-Pin 12V EPS connector there are also four 62-Pin PCIe connectors available to supply graphics cards with power Additional components are powered by means of eight SATA- & four Molex connectors Note For environmental reasons the manufacturer does not supply a wall outlet power cable with the unit Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic regulation rifle-bearing fan) Colour Black (PSU fan) Efficiency min 908787 percent at 5020100 percent load on European 230 Volt network Meets requirements for 80 PLUS Gold Active PFCForm factor ATX 12V V231 Output 600 W33V 16 A5V 16 A33V & 5V combined 100 W12V 576 W 48 A-12V 6 W 05 A5 Vsb 15 W 3 AConnectors (removable)1x 204-Pin ATX12VEPS12V1x 44-Pin ATX12VEPS12V4x 62-Pin PCIe 8x SATA4x 4-Pin Molex Safety OVPUVP (protection against over- & undervoltage)SCP (short circuit)OPP (overload)OCP (over-current protection on 12 33 & 5 Volt rails) Manufacturer's guarantee 3 Years ...

The Enclave Series from Kolink represents a new series of high-performance power supplies with 80 PLUS Gold certification The premium quality components advance design & powerful 12V single-rail ensure robust & reliable power delivery as well as precise voltage regulation The premium quality power supply is rounded off by the welcome addition of fully modular cable management as well as a whisper-quiet 120 mm fan THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATED FOR 700 WATTS AT A GLANCE700 Watt PSU with powerful 58A single rail High efficiency thanks to 80 PLUS Gold certification Quiet 120 mm fan Fully modular cable management with flat cables Four 62-Pin PCIe connectors for graphics cards Eight SATA- & four Molex connectors THE KOLINK ENCLAVE 80 PLUS GOLD PSU RATED AT 700 WATTS IN DETAILThe advanced design & the use of high-quality components mean that Kolink has been able to produce an efficient & high-performance power supply in the form of the Enclave 80 PLUS Gold 700W To this end the manufacturer has opted for LLC transformers & DC-DC technology alongside independent voltage regulation This combination also provides benefits to the unit's operating efficiency as well as the precision with which voltages are regulated particularly when it comes to asymmetric loads As a result the Enclave is capable of outputting nearly its entire rated power delivery through the 12 Volt rail if necessary This can be up to 48A & means that all your high-performance components are kept well-supplied with all the power they need The high operating effectiveness means that it meets the criteria for 80 PLUS Gold certification as well as an average efficiency of 92 percent when used on a European 230 Volt network In terms of cooling the units use a slow-spinning 120 mm fan with ultra-durable rifle bearings Apart from the impressive performance specifications the Kolink Enclave 700W isn't short of connectivity options either in addition to a 204-Pin ATX- & a 44-Pin 12V EPS connector there are four 62-Pin PCIe connectors for powering your graphics cards Additional components are powered by means of eight SATA- & four Molex connectors Note For environmental reasons the manufacturer does not supply a wall outlet power cable with the unit Technical Details Dimensions 150 x 86 x 160 mm (W x H x D) Fan 120 mm (automatic regulation rifle-bearing fan) Colour Black (PSU fan) Efficiency min 908787 percent at 5020100 percent load on European 230 Volt network Meets requirements for 80 PLUS Gold Active PFCForm factor ATX 12V V231 Output 700W33V 16 A5V 16 A33V & 5V combined 100 W12V 696 W 58 A-12V 6 W 05 A5 Vsb 15 W 3 AConnectors (removable)1x 204-Pin ATX12VEPS12V1x 44-Pin ATX12VEPS12V4x 62-Pin PCIe 8x SATA4x 4-Pin Molex Safety OVPUVP (protection against over- & undervoltage)SCP (short circuit)OPP (overload)OCP (over-current protection on 12 33 & 5 Volt rails) Manufacturer's guarantee 3 Years ...

Renowned for their innovative & high-performance cases Kolink has now brought the new Ethereal Midi-Tower to market representing a feature-rich gaming case that offers an abundance of space beneath its stylish exterior for all the powerful gaming hardware you could want The tempered glass side door will allow users to enjoy an unobstructed view of their high-end gaming setup complete with compatibility for E-ATX motherboards Given the use of tempered glass aesthetics are important & a PSU shroud cleverly conceals unsightly cables The front of the case has the appearance of brushed aluminium almost indistinguishable from the real thing & this accentuates the stylish exterior overall
- with the digitally addressable RGB-LED strip only adding to the case's impressive aesthetics A switch on the IO panel enables lighting control Alternatively the lighting strip can also be connected directly to the motherboard & controlled there if you prefer A fine mesh with integrated dust filter in the roof of the case helps keeps your hardware clean & dust-free A pre-installed 120mm fan provides more than adequate airflow THE FEATURES OF THE KOLINK ETHEREAL MIDI-TOWER AT A GLANCEStylish Midi-Tower supporting up to E-ATX motherboards Tempered glass side panel with hinges Brushed aluminium-look front Smart digitally addressable RGB lighting on the front One pre-installed 120mm fan on the rear Up to five 120mm- & four 140mm fans possible Space for graphics cards up to 380mm CPU coolers up to 160mm tall IO Panel with controller for RGB-LEDs 1x USB (Universal Serial Bus) 31 Type C 1x USB (Universal Serial Bus) 30 und 2x USB (Universal Serial Bus) 20KOLINK ETHEREAL PLENTY OF SPACE FOR POWERFUL GAMING HARDWAREEven though the case's

Dimensions correspond to those of a Midi-Tower the Ethereal utilises its ingenious design to enable support for E-ATX motherboards Even graphics cards measuring up to 380 mm will enjoy plenty of space towards the front of the case Most CPU coolers measuring up to 160mm in height will also fit with space to spare The implementation of a smart shroud helps conceal the PSU & HDD cage in which users are free to install two 35- or two 25 drives To the rear of the motherboard lies a bracket offering support for two more 25 SSDs Those who prefer to opt for air cooling will be pleased to know that there are plenty of mounting points for 120mm fans The front allows for the installation of two 120mm- or two 140mm fans The roof allows for either two 120mm- or two 140mm fans The roof of the case is equipped with a mesh that helps ensure maximum airflow with a minimum of unwanted dust This is also possible in no small part thanks to the smart use of dust filters meaning that the case's interior will rarely need special cleaning A single 120mm occupies a slot at the back of the case The front of the case supports a 280mm radiator & of course the rear fan can be replaced with a 120mm radiator if you prefer TEMPERED GLASS & RGB-LEDS GET YOUR HARDWARE LOOKING GREATThanks to Kolink's clever choice of locations for the case's cable guides & brackets users can look forward to a strikingly smart & clean-looking case The spacious interior can be admired from the outside thanks to the case's use of a tempered glass side door which of course uses hinges to make opening & closing the case a breeze A strip of digitally addressable RGB-LEDs is attached to the side of the brushed aluminium front A switch on the IO panel is responsible for controlling them along with their accompanying lighting effects Alternatively the strip can also be connected & controlled directly to the mainboard Then the RGB switch on the IO panel can also be used as a reset button In addition to the RGBReset switch there is also a USB (Universal Serial Bus) 31 Type C slot a USB (Universal Serial Bus) 30 slot & two USB (Universal Serial Bus) 20 ports as well as 3.5cm sockets for headphones & microphone & finally a power & HDD-LED Technical Details Dimensions (H x B x D) 435 x 205 x 455 mm Material Steel tempered glass plastic Weight approx 57kg Colour Black Form factor E-ATX ATX Micro-ATX Mini-ITXTotal possible fans 2x 120140 mm (roof)2x 120140 mm (front)1x 120 mm (rear) Pre-installed 1x 120 mm rear Radiator Mountings 1x 240280 mm (front)1x 120 mm (rear) Filter Roof bottom Drive bays 2x 3525 (internal HDD cage)2x 25 (internal motherboard tray)PSU 1x Standard ATX (optional) Expansion slots 7IO Panel 1x USB (Universal Serial Bus) 31 Type C (internal connection)1x USB (Universal Serial Bus) 30 Type A (internal connection)2x USB (Universal Serial Bus) 20 (internal connection)1x Audio In Out 1x RGB-Reset Switches Max GPU length 380 mm Max CPU cooler height 160 mm Max PSU depth 200 mm


...

The Kolink Horizon is an impressive Midi Tower case with several unique features The case's tinted tempered glass side & front panels are particularly striking The dark tinted glass creates a distinct look that is even better when combined with the four colourful RGB fans Kolink have bundled with the case The side panel has a slightly curved shape Rather than being a standard glass panel the lower end has been partially tapered off which leaves room on for additional vents to improve airflow THE KOLINK HORIZON AT A GLANCETinted tempered glass side & front panels Bundled with four 120mm rainbow dual ring fans addressable via a fan hub controller Curved side panel for optimal airflow THE KOLINK HORIZON IN DETAILThe Kolink Horizon is a Midi Tower case with a striking design It

Includes:: tinted tempered glass front & side panels which look especially good when paired with RGB LED fans The case is bundled with four 120mm Dual Ring Rainbow RGB fans These plug into a fan hub controller which is controlled via either a button on the IO panel or an included remote control A RANGE OF COOLING & CONNECTIVITY OPTIONSAside from its impressive appearance the Kolink Horizon features a range of useful & practical elements For instance there are many possibilities when it comes to cooling Air cooling being served by four pre-installed RGB Ring Fans (three in the front & one in the back) However you can also install two additional 120mm fans on the case's roof & a further two 120mm fans in the base For those who prefer water cooling radiators of up to 360mm can be fitted to the front of the case while a 120mm radiator can be installed at the back The Kolink Horizon offers many options in respect to connectivity there is an IO panel that features two USB (Universal Serial Bus) 30 ports along with an audio jack & one USB (Universal Serial Bus) 20 port in addition there is space internally for two 2535 HDDSSD bays & three 25 HDDSSD bays The Kolink Horizon features great support for components including room for up to 345mm VGA cards 160mm CPU coolers & 240mm PSUs SPECIFICATIONSModel Horizon RGB Black Type Midi Tower Case Colour Matte Black with Ring RGB LED's & tempered glass front & side panels Case Material 06mm Steel Tempered Glass Power Supply Orientation Bottom Motherboard Support ATXMicro-ATXMini-ITXInternal 35 Bays 2 Internal 25 Bays 5 (2 x 2535 combo) Expansion Slots 7 Front Ports 2 x USB301 x USB20HD-Audio x 1 Mic x 1RGB Controller Cooling System Front
- 3 x 120mm RGB Ring Fan (included) Rear
- 1 x 120mm RGB Ring Fan (included) Top
- 2 x 120mm (optional) Shroud
- 2 x 120mm (optional) Radiator Support Front
- Up to 360mm Rear
- Up to 120mm Dimensions 468 x 202 x 454mm Clearance VGA
- 345mm CPU Cooler
- 160mm PSU
- 240mm Gross Weight 86KG










...

Kolink gave the Inspire K2 ARGB something that helps it stand out from the crowd the front is equipped with a striking design as well as an ARGB-LED strip which can be controlled via the IO panel Together the front is reminiscent of a printed circuit board or a scene from one of the Tron films The almost invisible recesses also serve to allow fresh air into the case The tinted tempered glass side panel offers users a view of the interior specifically of the Micro-ATX motherboard Naturally this Micro-ATX case supports powerful hardware & plenty of drives that would combine to make this an exceptional gaming system This makes the Kolink Inspire K2 ARGB one of the ideal cases for gamers on the lookout for something with great value & an eye for unusual designs THE KOLINK INSPIRE K2 ARGB MICRO-ATX CASE AT A GLANCEStrikingly shaped front with ARGB lighting Tempered glass side panel & PSU slot in the top Space for 1x 120mm fan in the front & 1x 92mm fan in the back (pre-installed) Space for graphics cards up to 320mm & CPU coolers up to 150mm IO Panel with one USB (Universal Serial Bus) 30 one USB (Universal Serial Bus) 20 & RGB-LED controls Rear 92mm Fan pre-installed Light & easy to transport at just 39kg VALUE MICRO-ATX CASE FROM KOLINK FOR GAMERSThe Kolink Inspire K2 ARGB is an extremely affordable Micro-ATX case that is in style terms oriented more towards gamers It can fit graphics cards up to 32cm in length What is particularly striking about it however is the front with its angular aesthetics as well as its PCB-inspired look complete with cutouts to help draw air into the case The look of the front is accentuated by the addition of semi-transparent strips behind which lies an ARGB-LED strip At the top towards the front lies the USB (Universal Serial Bus) 20- & USB (Universal Serial Bus) 30 connection as well as RGB lighting controls A tinted tempered glass side panel helps to round out the stylish design of the Inspire K2 ARGB The interior of the case provides space for Micro-ATX or Mini-ITX motherboards Graphics cards can be up to 320mm long & CPU coolers are limited to 150mm meaning that there is more than adequate space for mainstream coolers In terms of cable management the cover on the right side is curved to provide that bit of extra space The front allows for a 120mm fan There is space for a 92 mm fan at the back Towards the topfront of the case lie two slots the top one can hold a 35- or 25 drive Under this in the second slot there is space for a 25 SSD At the bottom users have the option of installing another 35- or 25 drive Technical Details Dimensions 382 x 188 x 393 mm (W x H x D) Material Steel (case) tempered glass (side panel) plastic (front) Weight approx 39kg Colour Black Form factor Micro-ATX Mini-ITXTotal possible fans 1x 120 mm (front)1x 92 mm (rear) (pre-installed) Radiator Mountings 1x max 120 mm (front) Drive Bays 2x 3525 max (internal upper cage bottom)1x 25 max (internal lower cage)PSU 1x Standard ATX (optional) Expansion slots 4IO Panel 1x USB (Universal Serial Bus) 301x USB (Universal Serial Bus) 202x 3.5cm jack (1x Audio-In -Out)RGB control Max GPU length 320 mm Max CPU cooler height 150 mm ...

Kolink gave the Inspire K3 ARGB something that helps it stand out from the crowd the front is equipped with a striking X design as well as two ARGB-LED strips which can be controlled via the motherboard (3 Pin) or IO panel The side cutouts serve as air inlets & dust filters The tempered glass side panel offers owners a view of the interior specifically of the Micro-ATX or Mini-ITX motherboard that has been installed The Micro-ATX case offers support for powerful hardware & plenty of drives to make creating your perfect gaming system a breeze This makes the Kolink Inspire K3 one of the best cases out there for gamers on the lookout for a deal but that have an eye for exceptional design THE KOLINK INSPIRE K3 ARGB MICRO-ATX CASE AT A GLANCEStriking front panel with ARGB lighting Tempered glass side panel & PSU slot in the top Space for 1x 120 mm fan at the front & a preinstalled 1x 92mm fan in the back Space for GPUs up to 320 mm long & CPU coolers 150 mm tall IO Panel with one USB (Universal Serial Bus) 30 one USB (Universal Serial Bus) 20 & ARGB-LED controls Light & easy to carry at just 39kg AFFORDABLE MICRO-ATX CASE FROM KOLINK FOR GAMERSThe Kolink Inspire K3 is an extremely affordable Micro-ATX case that is in style terms oriented more towards gamers It can fit graphics cards up to 32cm in length What stands out about it in particular is the use of transparent strips in the shape of an X that is illuminated via two ARGB-LED strips The side-mounted vents help ensure your components receive plenty of airflow & at the top towards the front lie the USB (Universal Serial Bus) 20- & USB (Universal Serial Bus) 30 connections as well as ARGB lighting controls
- although this can also be controlled via a 3-pin cable to the motherboard if needed A tinted tempered glass side panel rounds out the stylish design of the Kolink Inspire K3 The interior offers support for a Micro-ATX- or Mini-ITX motherboard The case also supports graphics cards up to 320 mm long & CPU coolers up to 150 mm in height
- more than enough space for most common models The right side offers plenty of space for cable management due to its shape The front allows for a 120 mm fan The back has a 92 mm fan pre-installed Towards the topfront of the case lie two slots the top one can hold a 35- or 25 drive Under this in the second slot there is space for a 25 SSD At the bottom users have the option of installing another 35- or 25 drive Technical Details Dimensions 382 x 188 x 393 mm (W x H x D) Material Steel (case) tempered glass (side panel) plastic (front) Weight approx 39kg Colour Black Form factor Micro-ATX Mini-ITXTotal possible fans 1x 120 mm (front)1x 92 mm (rear) Pre-installed fans 1x 92 mm (rear) Radiator Mountings 1x max 120 mm (front) Drive Bays 2x 3525 max (internal upper cage bottom)1x 25 max (internal lower cage)PSU 1x Standard ATX (optional) Expansion slots 4IO Panel 1x USB (Universal Serial Bus) 301x USB (Universal Serial Bus) 202x 3.5cm jack (1x Audio-In -Out)ARGB Control Max GPU length 320 mm Max CPU cooler height 150 mm

...

The Inspire K5 Midi-Tower from Kolink has now introduced their long awaited Inspire range The front has received a unique one-of-a-kind design complete with a digitally addressable RGB-LED strip which can be controlled either via the IO panel or via a 3-pin connector on a compatible motherboard The RGB-LED strip illuminates the striking design adorning the front of the panel The side-facing cutouts on the front serve to effectively improve airflow while doubling as dust filters The tinted tempered glass side panel affords users an unobstructed view into the interior meaning you can enjoy a view of your high-end ATX motherboard Moreover this Midi-Tower design is more than capable of supporting an array of powerful hardware along with plenty of drives to ensure you can create the exact gaming system you desire complete with the necessary power to back it up All in all this makes the Kolink Inspire K5 into the ideal case for those who wish to save money where possible but without compromising on an attractive design THE KOLINK INSPIRE K5 MIDI-TOWER AT A GLANCEStrikingly attractive front with RGB lighting Side panel in tinted tempered glass with PSU shroud Space for a 240 mm radiator in the front Space for graphics cards up to 310 mm in length & CPU coolers up to 160 mm IO Panel with one USB (Universal Serial Bus) 30 one USB (Universal Serial Bus) 20 audio ports & RGB-LED controller AFFORDABLE ATX CASE FROM KOLINK FOR GAMERSThe Kolink Inspire K5 is a very affordable Midi-Tower which is designed for gamers that appreciate style & attractive design as well as performance Graphics cards up to 31 cm in length are supported What is especially striking is the front panel with its opaque stripe that is illuminated by means of a digitally addressable RGB-LED strip
- thereby giving the case a unique look The side-mounted grills ensure a more than adequate airflow At the top of the case towards the front users will find the IO panel with both a USB (Universal Serial Bus) 20 port along with a single USB (Universal Serial Bus) 30 port as well as a controller for digitally addressable RGB lighting although as an alternative this can also be connected via a 3-pin cable directly to the motherboard A tinted tempered glass side panel rounds out the stylish design of the Kolink Inspire K5 The interior offers space for ATX Micro-ATX- or a Mini-ITX motherboard of your choosing Graphics cards can be up to 31I0 mm in length while CPU coolers enjoy 160 mm of space more than enough for most current models When it comes to cable management the right side cover has a curve to it in order to bring offer additional space The front allows for three 120 mm fans to be installed The rear has space for one 120 mm fan There can also be 2 x 120mm fans installed on the PSU shroud Water cooling is likewise well catered for a 360 mm radiator can be installed in the front & the rear has space for a 120mm radiator Behind the shroud supports two 35- or 25 drives & the rear of the motherboard tray has space for two additional 25 drives should you require the extra storage capacity Technical Details Dimensions 410 x 205 x 440 mm (W x H x D) Material Steel (case) tempered glass (side panel) plastic (front) Weight approx 55kg Colour Black Form factor ATX Micro-ATX Mini-ITXTotal possible fans 3x 120 mm (front)1x 120 mm (rear) Radiator Mountings 1x max 240 mm (front)1x 120 mm (rear) Drive Bays 2x 3525 max (internal)2x 25 max (internal)PSU 1x Standard ATX (optional) Expansion slots 7IO Panel 1x USB (Universal Serial Bus) 301x USB (Universal Serial Bus) 202x 3.5cm ports (1x Audio-In -Out)RGB Controller Max GPU length 310 mm Max CPU cooler height 160 mm
...

Kolink set out to create a special Micro-ATX case the result of these efforts is the Inspire K6 a case with a brushed aluminium-look front complete with a striking design & that

Includes:: a digitally addressable RGB-LED strip that is controlled via the IO panel The mesh design serves to provide your components with all their airflow they need The tempered glass side panel affords users a view of the interior & the user's Micro-ATX form factor motherboard But just because this is a Micro-ATX case it doesn't mean that you can't install a huge amount of powerful hardware along with plenty of storage This combination of features means the Kolink Inspire K6 is the perfect case for those on the lookout for affordability that still offers exceptional design & features THE KOLINK INSPIRE K6 MICRO-ATX CASE AT A GLANCEStriking front panel with brushed aluminium look & ARGB lighting Tempered glass side panel & PSU shroud 1x Pre-installed 120 mm fan at the rear Space for up to 5x 120 mm fans 240 mm radiators on the front & roof Space for graphics cards up to 350 mm long & CPU coolers 162 mm tall IO Panel with 1x USB (Universal Serial Bus) 30 2x USB (Universal Serial Bus) 20 & RGB-LED controller Space for 2x 3525- & 2x 25 drives INSPIRE K6 AFFORDABLE MICRO-ATX CASE FROM KOLINK FOR GAMERSThe Kolink Inspire K6 is a remarkably affordable Micro-ATX case designed for gamers that want a rig that looks great as well as performs great It can fit graphics cards up to 35 cm in length What is striking about the case however is its implementation of a brushed aluminium-look front panel with a mesh for ample airflow The front also features a digitally addressable RGB-LED strip which allows users control either via the IO panel or directly via the motherboard On the top of the cover towards the front users will find the IO panel itself featuring both USB (Universal Serial Bus) 20 ports & a USB (Universal Serial Bus) 30 connector along with the controls for the RGB lighting A tinted tempered glass side panel rounds out the attractive design of the Inspire K6 Inside has a space for a Micro-ATX- or a Mini-ITX motherboard Graphics cards may be 350 millimeters long & CPU coolers up to 162 mm tall
- which is more than enough space for most common models For cable management there are cable guides located on the tray & in the power supply cover along with plenty of space between the motherboard tray & the right side panel Power supplies may be up to 170 millimeters long luxurious COOLING OPTIONS PLENTY OF SPACE FOR DRIVESUp to five 120 millimeter fans can fit in the confines of this spacious Micro-ATX gaming case In addition to the 120 mm slot that comes pre-installed on the back there are two more spaces on the roof & on the front There is a magnetic dust filter located in the roof to help ensure that the hardware doesn't get dusty inside Also at the front there is a filter located behind the air vents Of course the power supply unit on the underside is also protected from dust If you prefer water- to air cooling then this is also an option At the front & on the roof users are free to install a 240 mm radiator CPU coolers up to 162 mm will fit comfortably Under the PSU shroud there is an HDD cage that can accommodate either two 35 or 25 drives In the interior next to the motherboard users are free to install two additional 25-inch drives The result of Kolink's efforts here is the epic K6 a case that has been designed from the ground up to make powerful yet attractive & compact gaming setups a reality Technical Details Dimensions 410 x 202 x 395 mm (W x H x D) Material steel (case) tempered glass (side panel) plastic (front) Weight approx 52kg Color Black Form factor Micro-ATX Mini-ITXFans possible in total 2x 120 mm (front side)2x 120 mm (cover)1x 120 mm (rear) Pre-installed 1x 120 mm (rear) Radiator mountings 1x max 240 mm (front side)1x max 240 mm (cover) Drive bays 2x 3525 inch max (internal HDD cage)2x 25 inch max (mainboard tray front) Power supply 1x standard ATX (optional) Extension slots 4IO Panel 1x USB (Universal Serial Bus) 302x USB (Universal Serial Bus) 202x 3.5cm jack (1x audio in out each)RGB control Maximum graphics card length 350 mm Maximum CPU cooler height 162 mm Maximum power supply length 170 mm


...

The Kolink internal USB (Universal Serial Bus) Hub is the ideal solution for increasing the amount of internal USB (Universal Serial Bus) ports available in your system Whilst most USB (Universal Serial Bus) hubs are externally mounted this board offers the possibility to duplicate the internal connections Thus for example the I O panel can be supplied via a connection The small circuit board is connected to an internal USB (Universal Serial Bus) port via the supplied cable & provides four internal USB (Universal Serial Bus) ports A separate 4-pole Molex supplies the compact USB (Universal Serial Bus) hub & the individual channels with power Mounting is via the supplied 3M adhesive strip allowing mounting to both magnetic &38; non magnetic surfaces Technical details Dimensions 95 x 12 x 29 mm (W x H x D) Material Plastic Inputs 1x USB (Universal Serial Bus) 20 internal 1x 4-pin Molex Outputs 4x USB (Universal Serial Bus) 20 internal Mounting 3M Adhesive strip ...