More From Contributor

TS-2EXT.2 Truing Stand Upright Extensions install in seconds on any TS-2 Truing St&, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat & downhill bikes), as well as on wheels with a 29” mountain bike tire installed. In addition, specially sized bosses on the TS-2EXT.2 serve as adaptors so the TS-2 Truing Stand can be used with wheels using 12mm, 15mm, 20mm or 25mm thru-axle hubs with removable axles. NOTE: The TS-2.2 does not require this adaptor to accommodate 29 wheels but does require it to fit hub widths from 180mm to 200mm. ...

Available

Designed especially for the home mechanic, the TS-8 allows accurate wheel truing at an economical price. Accepts wheels from 16” to 29”, with or without the tire mounted. Innovative sliding dropout allows quick wheel installation, no matter what the hub width (up to 170mm). Dishing (centering) is performed by simply flipping the wheel in the st&. Constructed from heavy gauge steel to resist flexing, the TS-8 can be used freestanding or bolted to a bench for extra stability. ...

Available

The TS-RK is a complete rebuild kit for the TS-2 truing st&. It is complete with the most commonly replaced small parts & the instructions needed to get your stand back into top working condition. In addition to making the stand more accurate & reliable, once installed, the new parts also allow the stand to be readjusted much more easily, should it be thrown out of adjustment. This is a great addition to the older TS-2 stands. If your stand has silver-colored shaft collars, upgrade with the TS-RK. ...

Available

The TS-TA makes it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, & 25mm thru axle front wheels, as well as Cannondale Lefty wheels. The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 & TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. ...

Available

Extensions to enable the TS2 wheel truing stand to take 20 mm thru-axle, extra wide hubs & very large diameter rim & tyre combinations. TS-2EXT Truing Stand Upright Extensions install in seconds on any TS-2 Truing St&, allowing the stand to be used on wheels with 160 mm width hubs including tandem & downhill bikes, as well as on 700C wheels with a 29 inch mountain bike tyre installed. In addition, specially sized bosses on the TS-2EXT serve as adaptors so the TS-2 Truing Stand can be used with wheels using 20 mm through axle hubs. ...

Available

With today’s lightweight components, torque wrench use in the shop is no longer an option—it’s a must for every mechanic. The TW-6 is a high quality, ratcheting, click type torque wrenches that accurately measure & apply the proper amount of torque to a component’s threaded fastener (s). Designed for higher torque settings for repairs & installation in the bottom bracket, cassette lockring & other areas that use a higher torque settings. For lower torque setting, see the TW-5 or TW-1. Comes with its own protective case. ...

Available

Park Tool TWS2C
- Fold-Up Torx Wrench Set. The TWS2C
- Fold-Up Torx Wrench Set is a selection of essential wrenches in a fold

...

Available

For a wheel to perform properly, it is important for the rim to be centered between the locknuts of the hub, or “dished”. To check this, & to make precision adjustments, a wheel alignment gauge (also called a “dishing tool”) is a must. An accurate & truly versatile wheel alignment gauge that belongs along side every truing st&. ...

Available

For a wheel to perform properly, it is important for the rim to be centered between the locknuts of the hub, or, “dished”. The WAG-5 accurately gauges dish on 24 x 1-38” to 29” wheels (ETRTO or ISO sizing of 571 to 630). Disassembles quickly for storage or travel & works with all hub types. ...

Available

The wrenches in the SCW-SET.3 use our Y head design for strength & a durable industrial phosphate finish. The handles are vinyl-dipped for comfort.

Includes:: all cone wrenches produced by Park Tool: 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 26, & 28mm sizes.

...

Available

Park Tool TW-5 Ratcheting Torque Wrench

With todays lightweight components, torque wrench use in the shop is no longer an option—its a must for every mechanic. The TW-5 is a high quality, ratcheting, click type torque wrenches that accurately measure and apply the proper amount of torque to a components threaded fastener(s). It is designed for lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.

Availability: In Stock
Supplier: Rutland Cycling
SKU: 104314

Description Reviews / Comments Add New

Product Description

With todays lightweight components, torque wrench use in the shop is no longer an option—its a must for every mechanic. The TW-5 is a high quality, ratcheting, click type torque wrenches that accurately measure & apply the proper amount of torque to a components threaded fastener (s). It is designed for lower torque settings that a shop or consumer would use for proper seat post, seat clamp & handlebar / stem applications. Comes with its own protective case.

Reviews/Comments

Add New

Intelligent Comparison

Available

Park Tool TW-6 Big Clicker Ratcheting Torque Wrench Rutland Cycling

£109.99

Available

Park Tool MWF-1 Metric Flare Wrench Rutland Cycling

£6.29

More From Contributor

Park Tool TW-5 Ratcheting Torque Wrench

Product Description

Reviews/Comments

Add New

Intelligent Comparison

Price History

Vouchers

Facebook

Jargon Buster

Supplier Information

Community Generated Product Tags

Contact Us

Information

My Account