•ATtiny 85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM•USB boot-loader with a nice LED indicator looks just like a USBtiny ISP so you can program it with AVRdude and/or the Arduino IDE• Mini-USB jack for power and/or USB (Universal Serial Bus) uploading, you can put it in a box or tape it up & use any USB (Universal Serial Bus) cable for when you want to reprogram• We really worked hard on the boot-loader process to make it rugged & foolproof, this board wont up & die on you in the middle of a project!•~5.25K bytes available for use (2.75K taken for the boot-loader)• On-board 3.3V or 5V power regulator with 150m A output capability & ultra-low dropout• Up to 16V input, reverse-polarity protection, thermal & current-limit protection• Power with either USB (Universal Serial Bus) or external output (such as a battery)
- it'll automatically switch over• On-board green power LED & red pin 1 LED• Reset button for entering the boot-loader or restarting the program• No need to unplug/replug the board every time you want to reset or update!•5 GPIO
- 2 shared with the USB (Universal Serial Bus) interface• The 3 independent IO pins have 1 analogue input & 2 PWM output as well• The 2 shared IO pins have 2 more analogue inputs & one more PWM output• Hardware I2C / SPI capability for breakout & sensor interfacing• Mounting holes! Yeah!• Really really small!• Please Click here for the detailed tutorial guide Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny 85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, & low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive dev-board & you aren't willing to take apart the project you worked so hard to design. It's our lowest-cost arduino-IDE programmable board! The Attiny 85 is a fun processor because despite being so small, it has 8K of flash, & 5 I/O pins, including analogue inputs & PWM 'analogue' outputs. We designed a USB (Universal Serial Bus) boot loader so you can plug it into any computer & reprogram it over a USB (Universal Serial Bus) port just like an Arduino. In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Arduino board. You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform. This is the 3V Trinket. There are two versions of the Trinket. One is 3V & one is 5V. Both work the same, but have different operating logic voltages. Use the 3V one to interface with sensors & devices that need 3V logic, or when you want to power it off of a Li Po battery. The 3V version should only run at 8 MHz. Use the 5V one for sensors & components that can use or require 5V logic. The 5V version can run at 8 MHz or at 16 M Hz by setting the software-set clock frequency. Even though you can program Trinket using the Arduino IDE, it's not a fully 100% Arduino-compatible. There are some things you trade off for such a small & low cost microcontroller!• Trinket does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data• Some computers' USB (Universal Serial Bus) v 3 ports don't recognize the Trinket's boot loader. Simply use a USB (Universal Serial Bus) v 2 port or a USB (Universal Serial Bus) hub in between• Trinket is not supported on Linux operating system at this time
- try Mac OS or Windows!


...

•ATtiny 85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM•USB boot-loader with a nice LED indicator looks just like a USBtiny ISP so you can program it with AVRdude and/or the Arduino IDE• Mini-USB jack for power and/or USB (Universal Serial Bus) uploading, you can put it in a box or tape it up & use any USB (Universal Serial Bus) cable for when you want to reprogram• We really worked hard on the boot-loader process to make it rugged & foolproof, this board wont up & die on you in the middle of a project!•~5.25K bytes available for use (2.75K taken for the boot-loader)• On-board 3.3V or 5V power regulator with 150m A output capability & ultra-low dropout• Up to 16V input, reverse-polarity protection, thermal & current-limit protection• Power with either USB (Universal Serial Bus) or external output (such as a battery)
- it'll automatically switch over• On-board green power LED & red pin 1 LED• Reset button for entering the boot-loader or restarting the program• No need to unplug/replug the board every time you want to reset or update!•5 GPIO
- 2 shared with the USB (Universal Serial Bus) interface• The 3 independent IO pins have 1 analogue input & 2 PWM output as well• The 2 shared IO pins have 2 more analogue inputs & one more PWM output• Hardware I2C / SPI capability for breakout & sensor interfacing• Mounting holes! Yeah!• Really really small!• Please Click here for the detailed tutorial guide Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny 85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, & low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive dev-board & you aren't willing to take apart the project you worked so hard to design. It's our lowest-cost arduino-IDE programmable board! The Attiny 85 is a fun processor because despite being so small, it has 8K of flash, & 5 I/O pins, including analogue inputs & PWM 'analogue' outputs. We designed a USB (Universal Serial Bus) boot loader so you can plug it into any computer & reprogram it over a USB (Universal Serial Bus) port just like an Arduino. In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Arduino board. You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform. This is the 5V Trinket. There are two versions of the Trinket. One is 3V & one is 5V. Both work the same, but have different operating logic voltages. Use the 3V one to interface with sensors & devices that need 3V logic, or when you want to power it off of a Li Po battery. The 3V version should only run at 8 MHz. Use the 5V one for sensors & components that can use or require 5V logic. The 5V version can run at 8 MHz or at 16 M Hz by setting the software-set clock frequency. Even though you can program Trinket using the Arduino IDE, it's not a fully 100% Arduino-compatible. There are some things you trade off for such a small & low cost microcontroller!• Trinket does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data• Some computers' USB (Universal Serial Bus) v 3 ports don't recognize the Trinket's boot loader. Simply use a USB (Universal Serial Bus) v 2 port or a USB (Universal Serial Bus) hub in between• Trinket is not supported on Linux operating system at this time
- try Mac OS or Windows!


...

• Three axes of measurements, X, Y & Z• Pins that can be used either as I2C or SPI digital interfacing• On-board 3.3V regulator & logic-level shifting circuitry means it works with any 3V or 5V microcontroller• Sensitivity levels can be set at +-2g (higher resolution for slow movements), +-4g, +-8g or +-16g (better for high speed tracking)•VCC takes up to 5V in & regulates to 3.3V with an output pin• Comes assembled & tested with a 9 pin 0.1"" standard header for use with breadboard or perfboard•25mm long by 19mm wide by 3.14mm high This lovely accelerometer has three axes of measurements, X, Y & Z & pins that can be used either as I2C or SPI digital interfacing.on-board 3.3V regulator & logic-level shifting circuitry means it works with any 3V or 5V microcontrollersensitivity levels can be set at +-2g (higher resolution for slow movements), +-4g, +-8g or +-16g (better for high speed tracking)VCC takes up to 5V in & regulates to 3.3V with an output pin Comes assembled & tested with a 9 pin 0.1"" standard header for use with breadboard or perfboard 25mm long by 19mm wide by 3.14mm high Once again Adafruit have provided an Arduino library for use with this kit ...

• Two sensors
- one 3-axis accelerometer, one magnetometer• Uses I2C to communicate•3.3V max chip, but added circuitry makes
...

• Develop interesting projects for the Arduino using GPS technology• Develop coding based applications for advanced projects• Highly sensitive receiver & wide channel give reliable GPS reception•-165 d Bm sensitivity, 10 Hz updates, 66 channels•5V friendly design & only 20m A current draw• Breadboard friendly + two mounting holes•RTC battery-compatible• Built-in datalogging•PPS output on fix•>25 Km altitude• Internal patch antenna + u.FL connector for external active antenna• Fix status LEDThe breakout is built around the MTK3339 chipset, a no-nonsense, high-quality GPS module that can track up to 22 satellites on 66 channels, has an excellent high-sensitivity receiver (-165 d B tracking!), & a built in antenna. It can do up to 10 location updates a second for high speed, high sensitivity logging or tracking. Power usage is incredibly low, only 20 m A during navigation. Best of all, we added all the extra goodies you could ever want: a ultra-low dropout 3.3V regulator so you can power it with 3.3-5VDC in, 5V level safe inputs, ENABLE pin so you can turn off the module using any microcontroller pin or switch, a footprint for optional CR1220 coin cell to keep the RTC running & allow warm starts & a tiny bright red LED. The LED blinks at about 1 Hz while it's searching for satellites & blinks once every 15 seconds when a fix is found to conserve power. If you want to have an LED on all the time, we also provide the FIX signal out on a pin so you can put an external LED on. Two features that really stand out about version 3 MTK3339-based module is the external antenna functionality & the the built in data-logging capability. The module has a standard ceramic patch antenna that gives it -165 d B sensitivity, but when you want to have a bigger antenna, you can snap on any 3V active GPS antenna via the u FL connector. The module will automatically detect the active antenna & switch over! Most GPS antennas use SMA connectors so you may want to pick up one of our u FL to SMA adapters. The other cool feature of the new MTK3339-based module (which we have tested with great success) is the built in datalogging ability. Since there is a microcontroller inside the module, with some empty FLASH memory, the newest firmware now allows sending commands to do internal logging to that FLASH. The only thing is that you do need to have a microcontroller send the " Start Logging" comm&. However, after that message is sent, the microcontroller can go to sleep & does not need to wake up to talk to the GPS anymore to reduce power consumption. The time, date, longitude, latitude, & height is logged every 15 seconds & only when there is a fix. The internal FLASH can store about 16 hours of data, it will automatically append data so you don't have to worry about accidentally losing data if power is lost. It is not possible to change what is logged & how often, as its hardcoded into the module but we found that this arrangement covers many of the most common GPS datalogging requirements. We've tested this version of the Ultimate GPS in a high-altitude balloon, & it kept fix up to 27km! A full tutorial is also available, which has tons of information about the module, how to use the data logger & more ...

• Reprogrammable micro-controller, analogue output, TTL serial output for debugging / data logging & of course, open source.• Data is passed through transparently from end to end, so you can use it with any USB (Universal Serial Bus) device at any speed• The power line has a 0.1 ohm current sense resistor an an INA169 high-side current sensor that is tracked by a little ATtiny 85 chip• The microcontroller is programmed to read the current draw as well as the bus voltage & light up the strip of LEDs on the side• The blue LEDs will light up, one for each Watt of power draw (which is ~200m A at 5V nominal), with a couple levels of PWM dimming for increasing current• You can measure up to 1A of current draw
- most USB (Universal Serial Bus) ports are rated for 500m A• It's safe to use this with something that draws up to 2 A of current, it'll just 'max out' the LEDs• The green LED is helpful to tell if you have too much droop on your power line• It stays lit as long as the voltage is higher than 4.5V, most devices won't charge effectively once it goes below that so if the green LED goes out, you know you should check your port, shorten the USB (Universal Serial Bus) cable, or reduce the current draw• It also prints out the voltage, current & wattage data as readable text on the TX pin at 9600 baud. Connect an FTDI friend, USB (Universal Serial Bus) console cable, microcontroller, XBee, whatever you want that can read 9600 baud TTL serial data for data logging, plotting or display• Please Click here to find the source code & schematic This little USB (Universal Serial Bus) port go-between is like a speed gauge for your USB (Universal Serial Bus) devices. Instead of hauling out a multimeter & splicing cables, plug this in between for a quick reading on how much current is being drawn from the port. Great for seeing the charge rate of your phone or tablet, checking your battery chargers, or other USB (Universal Serial Bus) powered projects. Comes as a mini kit with an assembled & tested PCB plus a separate USB (Universal Serial Bus) jack & plug as shown above. Before use, solder the jack & plug. It'll only take you a few minutes & can be done with any soldering iron. Or, advanced users can splice it between a USB (Universal Serial Bus) extension cable. Please note: this is a handy gadget but it isn't a multimeter! We do some basic calibration during test, but the serial output readings are not precise & should be used as a basic guide rather than lab-grade data plots. Assume a variance of at least 0.1V & 50m A due to noise, thermal changes, etc.
...

• Short range
- best results in the 10-150mm range•5V compliant so you can use it with 3.3V or 5V logic• Works best at 5V as the
...

• Decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM & ADPCM)• Record audio in both PCM (WAV) & compressed Ogg Vorbis• Do all sorts of stuff with the audio such as adjusting bass, treble, & volume digitally• Comes with a micro SD holder to let you play music straight from an SD card! • Special MIDI mode that you can boot the chip into that will read 'classic' 31250 Kbaud MIDI data on a UART pin & act like a synth/drum machine
- there are dozens of built-in drum & sample effects!•3.3v & 1.8v regulators onboard with ferrite beads & analogue filtering for quality analog output• Microphone input port that you can wire up a line-in or mic to & record compressed audio•8 GPIO pins broken out & they all have built in 100K pulldowns, simply connect your button from the GPIO pin to 3.3V for an active-high connection• Interface pins all 5V compliant with level shifters so you can use the chip at 3V or 5V power/logic!• Comes with 220u F stereo blocking capacitors on the output. This means you can plug the output into headphones or a stereo without risk of damage• Click here for the Adafruit tutorial This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM & ADPCM). It can also be used to record audio in both PCM (WAV) & compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting bass, treble, & volume digitally. There is also 8 GPIO pins that can be used for stuff like lighting up small LEDs or reading buttons. All this functionality is implemented in a light-weight SPI interface so nearly any microcontroller can play audio from an SD card. There's also a special MIDI mode that you can boot the chip into that will read 'classic' 31250 Kbaud MIDI data on a UART pin & act like a synth/drum machine
- there are dozens of built-in drum & sample effects! But the chip is a pain to solder, & needs a lot of extras. That's why we spun up the best breakout, perfect for use with an Arduino but also good for other microcontrollers that just don't have the computational power to decode MP3s. The breakout is slim enough to fit on a breadboard with 1 row of holes left over for wiring. There's 3.3v & 1.8v regulators onboard with ferrite beads & analogue filtering for quality analogue output. There's a microphone input port that you can wire up a line-in or mic to & record compressed audio. All 8 GPIO are broken out & they all have built in 100K pulldowns, simply connect your button from the GPIO pin to 3.3V for an active-high connection. You'll likely want to play music from a micro SD card so we added a holder on-board. & since we know so many of our customers use 5V microcontrollers like the Arduino, we made the interface pins all 5V compliant with level shifters so you can use the chip at 3V or 5V power/logic! Each order comes with a fully assembled & tested breakout board, some 0.1" male header you can solder to the breakout so it plugs into a breadboard & a bonus stereo headphone jack that will be handy when you want to plug headphones in!

...

Simple stylish design with snap-on cap Take your data with you anywhere Store your documents movies music & photos Backwards compatible with USB2.0 & USB1.1

Dimensions L x W x H 69.9 x 17.25 x 9.5 mm Weight 25g ADATA C801 comes with a snap-on cap that resembles a ballpoint pen design in addition to its sizable storage capacity & high-speed transmission interface. These features make the ADATA C801 the perfect flash drive for anyone who desires simplicity & the latest high-tech gadgetry. The OSto GO tool assists you by converting your Microsoft Windows 7 Installation DVD to an ADATA portable storage device providing you the convenience of being able to quickly install Windows 7 via USB (Universal Serial Bus) booting without the need for an optical drive. The powerful UFDto Go tool synchronizes data e-mails & your Favorites affording you true mobility.

...

• Born to be tough• Shockproof cased portable external hard drive that is 100% waterproof• Stores up to 250 HD quality movies• Wrap around USB (Universal Serial Bus) 3.0 cable• Bright cold-blue LED•USB 3.0 ultra high-speed interface, also compatible with USB (Universal Serial Bus) 2.0 & USB (Universal Serial Bus) 1.0 ports• Fully meets U.S. military drop test MIL-STD-810G 516.5 procedure & water resistant to IEC 529 IPX7 standards (submersible 1 metre for 30 min)• Supports Windows XP, Vista, 7, 8 / for Mac OS X 10.6 or later / Linux Kernel 2.6 or later • Dimensions (L x W x H): 132 x 99 x 21.5 mm• Weight: 220 g•AHD710-1TU3-CBLDash Drive Durable HD710 external hard drives are officially listed on the appearance of rugged, fast & reliable mobile data access. The HD710's chassis is produced with unique silicone materials, is shockproof & waterproof (IPX7) with military grade construction, ultra-fast USB (Universal Serial Bus) 3.0 interface. The lively style & dynamic design of the product can match the needs & styles of sports & outdoor activities enthusiasts. ...