An amazing & environmentally friendly rust remover! It has been proven to effectively remove even deep rust from all types of mild steel & iron. Frost Rust Remover is safe on all surfaces & will not harm copper, brass aluminium, plastic, rubber or vinyl. It is non-toxic, non-flammable, biodegradable & contains no acids, alkalis or petroleum solvents. Simple to use with effective result. You can reuse Frost Rust Remover several times until its performance starts to deteriorate. It is safe for use in fuel tanks, spray cabinets, ultrasonic cleaners, pressure washers, pumps & vats. Available in 1L, 5L or 25L.

Features: Effectively remove even deep rust. Easy to use & reusable several times. Non-toxic, non-corrosive, non-flammable. Safe on all surfaces including Copper, Brass, Aluminium, Mild Steel & Iron. Directions: Step 1: Remove dirt & pre-clean item. Step 2: Rinse then completely immerse item in the solution for 1-12 hours depending on the depth & age of the rust. Check progress periodically. Step 3: Once rust is removed, rinse item well with water. * For fuel tank de-rusting: Completely fill the tank with Frost Rust Remover & rotate the tank every hour until the rust has been removed. Drain completely & rinse well with water. Air dry & fill with petrol immediately to eliminate flash rust.

...

An amazing & environmentally friendly rust remover! It has been proven to effectively remove even deep rust from all types of mild steel & iron. Frost Rust Remover is safe on all surfaces & will not harm copper, brass aluminium, plastic, rubber or vinyl. It is non-toxic, non-flammable, biodegradable & contains no acids, alkalis or petroleum solvents. Simple to use with effective result. You can reuse Frost Rust Remover several times until its performance starts to deteriorate. It is safe for use in fuel tanks, spray cabinets, ultrasonic cleaners, pressure washers, pumps & vats. Available in 1L, 5L or 25L.

Features: Effectively remove even deep rust. Easy to use & reusable several times. Non-toxic, non-corrosive, non-flammable. Safe on all surfaces including Copper, Brass, Aluminium, Mild Steel & Iron. Directions: Step 1: Remove dirt & pre-clean item. Step 2: Rinse then completely immerse item in the solution for 1-12 hours depending on the depth & age of the rust. Check progress periodically. Step 3: Once rust is removed, rinse item well with water. * For fuel tank de-rusting: Completely fill the tank with Frost Rust Remover & rotate the tank every hour until the rust has been removed. Drain completely & rinse well with water. Air dry & fill with petrol immediately to eliminate flash rust.

...

An amazing & environmentally friendly rust remover! It has been proven to effectively remove even deep rust from all types of mild steel & iron. Frost Rust Remover is safe on all surfaces & will not harm copper, brass aluminium, plastic, rubber or vinyl. It is non-toxic, non-flammable, biodegradable & contains no acids, alkalis or petroleum solvents. Simple to use with effective result. You can reuse Frost Rust Remover several times until its performance starts to deteriorate. It is safe for use in fuel tanks, spray cabinets, ultrasonic cleaners, pressure washers, pumps & vats. As well as being used for general rust application, Frost Rust Remover can be utilised to target deep rust from the entire cooling system. It uses the latest technology in rust & corrosion removal to completely revitalise automotive cooling systems.   It removes rust scale & deposits from radiators, water pumps, water jackets, engine blocks, & heads. During Summer months rust can be just as much of a problem as rust & corrosion act as an insulator, causing vehicles to overheat. This product restores the engine's ability to transfer heat to the coolant allowing engines to run cooler & last longer.  Contains non-toxic, non-corrosive & non-flammable ingredients meaning it will not harm or clog your engine. Available in 1L, 5L or 25L.

Features: Effectively remove even deep rust. Easy to use & reusable several times. Non-toxic, non-corrosive, non-flammable. Safe on all surfaces including Copper, Brass, Aluminium, Mild Steel & Iron. Directions: Step 1: Remove dirt & pre-clean item. Step 2: Rinse then completely immerse item in the solution for 1-12 hours depending on the depth & age of the rust. Check progress periodically. Step 3: Once rust is removed, rinse item well with water. * For fuel tank de-rusting: Completely fill the tank with Frost Rust Remover & rotate the tank every hour until the rust has been removed. Drain completely & rinse well with water. Air dry & fill with petrol immediately to eliminate flash rust.

...

Blast rust, corrosion & paint on large parts in an enclosed cabinet to keep dust off the floor & out of the air; Heavy steel construction, single door on the side; Transparent glass viewing window; Air compressor delivery of 40-80PSI & 15-25CFM; Overall dimensions: 150cm (H) x 83cm (L) x 63cm (W) ...

Clean parts quickly and easily; Through the sealed gloves parts, you control the high-efficiency air blast gun inside, directing 100 maximum PSI abrasive flow to clean parts fast; For use with glass beads, silica s&, alum oxide & more; Transparent plastic top door; Air compressor delivery of 100PSE & 5CFM ...

Surface Preparation Prior to applying the topcoat, apply a suitable primer.  The surface must be free from all contamination including rust, grease & moisture. First sand old paintwork & coated parts & then prime. Once dry, sand smooth with P600 sandpaper. Before use, carefully read & note the warning text on the label Coverage: 1.25
- 1.75m² per 400ml Drying times*: Dust Free 5
- 10 minutes Tack Free 4 hours Cured after 24 hours  * The drying time depends on temperature, humidity & the thickness of the applied coat.

...

Without a doubt one of the most versatile sheet metal working tools you could hope to find. The Shrinker / Stretcher will quickly & easily pull shape into either steel up to 1.2mm or aluminium up to 2mm. Use it to fabricate repair panels anywhere on your car but especially those awkward areas around headlights, around the edges of window frames, door edges, rain channels, wheel arch rims etc. With the Shrinker/ Stretcher you don't need to cut-&-weld in order to create curves in angled sections
- simply shrink or stretch the metal into smooth even curvatures in a fraction of the time. Produces radii as small as 76mm. Body has two 3/8 UNC threaded holes for bench mounting or bolt it to a piece of heavy angle iron for quick mounting in your vice. Set

Includes:: one body, one handle, & two jaws. Complete with instructions. Also available with two bodies & two jaws Read " How Do I Use the Shrinking / Stretching Machine? " & " 10 MUST-HAVE Restoration Tools " from Technical Article.


...

Use to fabricate or repair metal work around wheel arches, door edges, window frames, rain channels...almost any metal fabrication requiring a combination curve & angle especially those awkward areas around headlights. Use the shrinker to contract metal for inside curves: use the stretcher to expand metal for outside curves. Set

Includes:: 2 jaws, 2 bodies & 2 handles. Works up to 18 gauge mild steel, 30 gauge stainless, & 16 gauge aluminum. Comes assembled & clamps in your vice or is pre-drilled for bench mounting. Read " How Do I Use the Shrinking / Stretching Machine? " & " 10 MUST-HAVE Restoration Tools " from Technical Article.

...

Hotcoat Powder Coating (1 LB) for Hot Coat Powder Coating Gun. Powder coating means that you can coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black
- Orange
- Brown
- Yellow
- Green
- Bright Red
- Silver
- White
- Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021









...

Hotcoat Powder Coating (1 kilo) for Hot Coat Powder Coating Gun. Powder coating means that you can coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black
- Orange
- Brown
- Yellow
- Green
- Bright Red
- Silver
- White
- Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021









...