Our range of quality engine Enamels are heat & oil resistant to give long lasting British engine colours. To be brushed on. If spraying, thin up to 10% with White Spirit Colours available: Aluminium, Black, BMC Green, Ford Dark Blue, Landrover Blue (Duck Egg Blue/ Light Green), Ford Green, Ford Red, Gold, Metallic Green, MG Maroon, Pale Blue, Pastel Green, Yellow, Jaguar Semi Gloss Black, British Racing Green, Basalt Grey. ...

The Frost Battery Terminal Protector & Indicator Aerosol cleans off corrosive deposits on battery terminals. The spray leaves a flexible, non conductive yellow film, which inhibits further corrosion. If acid is present the film will change colour to red, a simple insurance against damage to battery tray etc. ...

Fits most bead rollers with a 22mm shaft.

Includes:: 9 steel dies & 1 polyurethane lower wheel Create offsets

...

17pcs Set Work on bearings or bushings easier without damaging the race & axle housing. This high quality 17pc set enables you to remove & install bushings for all types of equipment. Collars fit most standard wheel bearing sizes. The three largest sizes fit most late-model 4 wheel drive vehicles. 3 Drivers: 110 / 140 / 160 mm 14 Adapters * Storage Case * Light Weight * Very Hard * Extreme Impact Resistant ...

Our range of quality engine Enamels are heat & oil resistant to give long lasting British engine colours. To be brushed on. If spraying, thin up to 10% with White Spirit Colours available:   Aluminium, Black, BMC Green, Ford Dark Blue, Landrover Blue (Duck Egg Blue/ Light Green), Ford Green, Ford Red, Gold, Metallic Green, MG Maroon, Pale Blue, Pastel Green, Yellow, Jaguar Semi Gloss Black ...

For looks & efficiency brakes need cleaning. The Frost Brake Cleaner aerosol removes brake fluid, oil, grease, asbestos & synthetic dust. Can even free seized brakes. Can stop brake squeal & clutch slip when caused by contamination & glazing. 500ml. ...

Our range of quality engine Enamels are heat & oil resistant to give long lasting British engine colours. To be brushed on. If spraying, thin up to 10% with White Spirit Colours available: Aluminium, Black, BMC Green, Ford Dark Blue, Landrover Blue (Duck Egg Blue/ Light Green), Ford Green, Ford Red, Gold, Metallic Green, MG Maroon, Pale Blue, Pastel Green, Yellow, Jaguar Semi Gloss Black, British Racing Green. ...

Hotcoat Powder Coating (1 kilo) for Hot Coat Powder Coating Gun. Powder coating means that you can coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black
- Orange
- Brown
- Yellow
- Green
- Bright Red
- Silver
- White
- Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021









...

Corrosion caused by moisture creeping into the small gaps between spot welded panels is one of the most common problems encountered on older vehicles. Using our Weld-thru Zinc Rich Primer prior to assembly will help combat this, but for assembled panels you can only hope to seal out moisture with a good quality seam sealer applied over the joint with a brush or spatula.
- Will not sag & is touch dry in hours
- Brushable Seam Sealer can be painted over in 2 to 3 hours.

...

Frost Bumper Black
- PCBLK1 Apply 3
- 4 coats • Allow 5mins to flash off between coats Carry out test spray Through cure 60mins

...