Tripp Lite 4-Outlet Power Strip with USB (Universal Serial Bus)-A Charging
- BS1363A Outlets, 220-250V, 13A, 1.8 m Cord, BS1363A
...

Power Distribution Anywhere in Any Medical Facility This 230V, 50/60 Hz medical-grade power strip supplies electricity to plug-connected components in operating rooms, patient-care vicinities, therapy rooms, imaging environments & administrative areas. Compliant with BS-1363 specifications, the PS610HGUK features a three-meter (10-foot) UK power cord with 13A fused Type G plug & six UK outlets. Armed with the Latest Safety Features to Protect Valuable Equipment A built-in replaceable 13A fuse controls all six outlets & protects against overloads by shutting them down if the equipment load draws too much power. The switchless design prevents the unit from being accidentally shut off, which would cut essential power to all connected devices. A green mains indicator lights to signal the power strip is properly connected to an AC power source. Long Cord Provides Enhanced Mobility The three-meter UK power cord allows for optimum flexibility when putting together a mobile health care workstation. The PS610HGUK can be mounted in a different area—or a completely different room—from where it draws AC power, putting you in control of getting reliable power service where you need it most. For best performance, connect the Type G plug to a standard 13A isolated ground receptacle with an isolated earth to eliminate unwanted ground noise. Equipotential Grounding Helps Your Equipment Perform at Its Best The included M5 earth ground stud & 250-millimeter-long earth wire help reduce unwanted leakage currents between connected devices. Comes Ready to Install & Use Right Out of the Box Built-in mounting tabs & flanges let you install the PS610HGUK on a wide variety of surfaces, including IV poles, mobile carts, crash carts & mobile medical workstations. The durable all-metal housing is designed to last a long time in demanding work environments. 2-Year Warranty & Environmentally Responsible Design The PS610HGUK comes with a 2-year warranty. It’s manufactured in compliance with strict Ro HS specifications, reflecting Tripp Lite’s commitment to environmental responsibility. &9679; Meets BS-1363 specifications for use inside & outside patient-care vicinities &9679; Long 3m UK power cord allows you great flexibility in placing the power strip &9679; Replaceable 13A fuse shuts down all 6 UK outlets in case of overload &9679; Mounting tabs/flanges for installation on IV poles, mobile carts & crash carts &9679; Switchless design protects connected devices from dangerous accidental shutdowns ...

Tripp Lite 6-Outlet Power Strip
- British BS1363A Outlets, 220-250V AC, 13A, 1.8 m Cord, BS1363A Plug, White. Cable length:
...

Tripp Lite 6-Outlet Power Strip
- British BS1363A Outlets, Individually Switched, 220-250V, 13A, 3 m Cord, White. Cable length:
...

Tripp Lite SRFILTER. Product

Colour: White, Compatibility: 25U, 42U, 45U, 48U.

Width:



...

Tripp Lite's 120V 20A metered PDU system with Automatic Transfer Switching (ATS) is a 16 outlet PDU with a digital display to indicate total PDU power consumption in amps. Outlets are factory programmed for sequential turn-on at 250 millisecond intervals when the PDU is first energized to prevent inrush-related equipment interaction on startup. Installed web/network monitoring card enables remote power monitoring & control. Remotely displays status of input power, load capacity, & outlet power status via secure network or web browser interface. Offers individual outlet control to power on, off, or cycle AC output to regain control of locked-up servers & other network devices. Load ramping & shedding provides programmable power management to any type of network configuration. Supports notification & logging of input power status, event notification, output power & load conditions. ...

Tripp Lite Metered ATS / Auto Transfer Switch provides a redundant power option for single-corded network devices. Dual input cords support separate connection to PRIMARY & SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored & stable. Super-fast switchover between primary & secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. Enables fault tolerant hot-swappable UPS protection when used with a single UPS & fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite Smart Online series is highly recommended for use as the primary UPS in a two-UPS application. ATS configurations utilizing separate mains circuits, backup generators & even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. Front input LED's display primary or secondary power availability. Features 200-240V 16/20A Automatic Transfer Switch (ATS) / Metered PDU (Agency de-rated to 16A continuous) Provides a redundant power option for critical networking equipment with a single input power cord 2 digit display reports output power consumption in amps 1U horizontal rackmount form factor; 14.8 in. / 37.6 cm depth 10 outlets (8 C13, 2 C19) Set of two C20 inlets support connection to separate PRIMARY & SECONDARY power sources Two 12ft / 3.6m C19 to C20 power cables included ATS circuits normally maintain output sourced from the primary input cable; As primary input power fails or becomes unstable, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored & stable ATS configurations enable fault-tolerant, hot-swappable UPS protection when used with a single UPS & fully redundant UPS protection when each cord is connected to a separate UPS system (in a two-UPS environment, the primary input cable must be supported by an online UPS with zero transfer time similar to Tripp Lite Smart Online series) Advanced ATS configurations utilizing separate mains circuits, backup generators & even separate out of phase utility power grid feeds are fully supported On-board ATS processor constantly evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the primary source Super-fast switchover between primary & secondary power sources occurs in 2-5 milliseconds ...

PDUMH30HVNET Switched, Metered, 2U rack PDU supports 30A maximum capacity at 208/240V (agency de-rated to 24 amps).



...

Tripp Lite Basic Power Distribution Units give IT Managers the ability to power multiple servers & vital networking hardware from a single input power source. Switch-free unfiltered electrical pass-through reliably distributes UPS or generator power to critical equipment in rack enclosures, network closets & more. Tooless mounting enables simple installation in button-mount compatible racks. Included mounting brackets support vertical installation in standard 2 & 4 post racks or other surfaces, such as under-counter or wallmount configurations. Plug retention brackets keep vital equipment plugged in & continuously powered. PDUV30HV 63.75 in. vertical 0U rack PDU supports 30A maximum capacity at 208/240V (agency derated to 24A).

Includes:: 10 ft. attached line cord with L6-30P input plug. 32 C13 & 6 C19 outlets support up to 38 directly connected pieces of networking equipment. Outlets are arranged in two separately breakered 15A load banks.

...

Tripp Lite single phase Metered PDU / Power Distribution Units offer real-time local reporting of load level in amps via built-in digital display. Enables visual monitoring of PDU load levels to prevent overloads as additional equipment is added. Offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design

Includes:: rugged all-metal housing & secure rackmount installation with included mounting accessories. Features 3.84k W 16A single phase 200/220/230/240V Metered Power Distribution Unit / PDU Two-digit lighted meter reports combined total output current in amps 10ft / 3m input cable with Blue IEC309 16A input plug 0U 63.75in / 162cm vertical rackmount format installs vertically, using no rack spaces 38 total outlets (6 C19, 32 C13) Plug-lock cord retention sleeves keep C20 & C14 equipment plugs from accidental disconnection Toolless installation supported in button-mount compatible equipment racks Bolt-down installation brackets support installation in other racks & additional surfaces

...