Hyper X Impact 8GB Kit DDR4 2400 M Hz SODIMM Memory (2x 4GB) Hyper X HX424S14IB/4 is a 512M x 64-bit (4GB) DDR4-2400 CL14 SDRAM (Synchronous DRAM) 1 Rx 8, memory module, based on eight 512M x 8-bit DDR4 FBGA components. Each module supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR4-2400 at a low latency timing of 14-14-14 at 1.2V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications are as follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR4-2400 CL14-14-14 @1.2V DDR4-2133 CL13-13-13 @1.2V XMP Profile 1: DDR4-2400 CL14-14-14 @1.2V FEATURES Power Supply: VDD = 1.2V Typical VDDQ = 1.2V Typical VPP
- 2.5V Typical VDDSPD = 2.25V to 3.6V On-Die termination (ODT) 16 internal banks; 4 groups of 4 banks each Bi-Directional Differential Data Strobe 8 bit pre-fetch Burst Length (BL) switch on-the-fly BL8 or BC4 (Burst Chop) Height 1.18” (30.00mm) SPECIFICATIONS CL (IDD) 14 cycles Row Cycle Time (t R Cmin) 46.75ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 29.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.

...

Hyper X HX424S14IB2/8 is a 1G x 64-bit (8GB) DDR4-2400 CL14 SDRAM (Synchronous DRAM) 1 Rx 8, memory module, based on eight 1G x 8-bit DDR4 FBGA components. Each module supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR4-2400 at a low latency timing of 14-14-14 at 1.2V. Features Power Supply: VDD = 1.2V Typical VDDQ = 1.2V Typical VPP
- 2.5V Typical VDDSPD = 2.25V to 3.6V On-Die termination (ODT) 16 internal banks; 4 groups of 4 banks each Bi-Directional Differential Data Strobe 8 bit pre-fetch Burst Length (BL) switch on-the-fly BL8 or BC4 (Burst Chop) Height 1.18” (30.00mm) Specifications CL (IDD) 14 cycles Row Cycle Time (t R Cmin) 45.75ns (min.) Refresh to Active/ Refresh 350ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 29.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0°C to 85°C Storage Temperature -55°C to +100°C

...

Hyper X Impact 8GB DDR4 2400 M Hz SODIMM Memory Hyper X HX424S14IB/4 is a 512M x 64-bit (4GB) DDR4-2400 CL14 SDRAM (Synchronous DRAM) 1 Rx 8, memory module, based on eight 512M x 8-bit DDR4 FBGA components. Each module supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR4-2400 at a low latency timing of 14-14-14 at 1.2V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications are as follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR4-2400 CL14-14-14 @1.2V DDR4-2133 CL13-13-13 @1.2V XMP Profile 1: DDR4-2400 CL14-14-14 @1.2V FEATURES Power Supply: VDD = 1.2V Typical VDDQ = 1.2V Typical VPP
- 2.5V Typical VDDSPD = 2.25V to 3.6V On-Die termination (ODT) 16 internal banks; 4 groups of 4 banks each Bi-Directional Differential Data Strobe 8 bit pre-fetch Burst Length (BL) switch on-the-fly BL8 or BC4 (Burst Chop) Height 1.18” (30.00mm) SPECIFICATIONS CL (IDD) 14 cycles Row Cycle Time (t R Cmin) 46.75ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 29.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.

...

Hyper X Impact 8GB Kit DDR4 2133 M Hz SODIMM Memory (2x 4GB) Hyper X HX421S13IB/4 is a 512M x 64-bit (4GB) DDR4-2133 CL13 SDRAM (Synchronous DRAM) 1 Rx 8, memory module, based on eight 512M x 8-bit DDR4 FBGA components. Each module supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR4-2133 at a low latency timing of 13-13-13 at 1.2V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications are as follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: JEDEC/ Pn P: DDR4-2133 CL13-13-13 @1.2V XMP Profile 1: DDR4-2133 CL13-13-13 @1.2V FEATURES Power Supply: VDD = 1.2V Typical VDDQ = 1.2V Typical VPP
- 2.5V Typical VDDSPD = 2.25V to 3.6V On-Die termination (ODT) 16 internal banks; 4 groups of 4 banks each Bi-Directional Differential Data Strobe 8 bit pre-fetch Burst Length (BL) switch on-the-fly BL8 or BC4 (Burst Chop) Height 1.18” (30.00mm) SPECIFICATIONS CL (IDD) 13 cycles Row Cycle Time (t R Cmin) 46.5ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 33ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.

...

Hyper X HX318LS11IBK2/16 is a kit of two 1G x 64-bit (8GB) DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 2 Rx 8, low voltage, memory modules, based on sixteen 512M x 8-bit DDR3 FBGA components per module. Total kit capacity is 16GB. Each module kit has been tested to run at DDR3L-1866 at a ow latency timing of 11-11-11 at 1.35V or 1.5V. Additional iming parameters are shown in the Pn P Timing Parameters section below. JEDEC standard 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) 933 M Hz f CK for 1866 Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset PCB: Height 1.180” (30.00mm), double sided components

...

Hyper X HX318LS11IB/4 is a 512M x 64-bit (4GB) DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory modules, based on eight 512M x 8-bit DDR3 FBGA compo-nents. This module has been tested to run at DDR3L-1866 at a low latency timing of 11-11-11 at 1.35V or 1.5V. Additional timing parameters are shown in the Pn P Timing Parameters section below. FEATURES JEDEC standard 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) 933 M Hz f CK for 1866 Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm 1%) Burst Length: 8 (Interleave without any limit, sequential with starting address 000 only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe On Die Termination using ODT pin

...

Hyper X HX318LS11IBK2/8 is a kit of two 512M x 64-bit (4GB) DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory modules, based on eight 512M x 8-bit DDR3 FBGA components per module. Total kit capacity is 8GB. Each module kit has been tested to run at DDR3L-1866 at a low latency timing of 11-11-11 at 1.35V or 1.5V. JEDEC standard 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) 933 M Hz f CK for 1866 Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (interleave without any limit, sequential with starting address '000' only), 4 with t CCD = 4 which does not allow seamless read or write (either on the fly using A12 or MRS) Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C degrees Asynchronous Reset

...

Hyper X HX318LS11IB/8 is a 1G x 64-bit (8GB) DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 2 Rx 8, low voltage, memory modules, based on sixteen 512M x 8-bit DDR3 FBGA compo-nents. This module has been tested to run at DDR3L-1866 at a low latency timing of 11-11-11 at 1.35V or 1.5V. Additional timing parameters are shown in the Pn P Timing Parameters section below. FEATURES JEDEC standard 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) Power Supply Bi-directional Differential Data Strobe VDDQ = 1.35V (1.28V ~ 1.45V) & 1.5V (1.425V ~ 1.575V) 933 M Hz f CK for 1866 Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C Asynchronous Reset On Die Termination using ODT pin

...

Get your Hyper X Cloud Alpha™ ready for the road with the Hyper X In-Line Mic. Just detach the standard mic & swap out the audio cable with the slim in-line mic. Easily answer or end phone calls & conveniently control your streaming media with a single button. The flexible, braided aux cable is designed to take the wear & tear of travel & gaming. Travel ready for mobile calls on the go Answer or end calls with ease Intuitive media controls Flexible braided cable Take calls on the go with your Hyper X Cloud Alpha Give your headset a portability upgrade with an in-line mic. Answer & end calls with ease Convenient control of your phone calls at your fingertips. One-button media controls Play media, pause, & advance tracks with a single button. Flexible, braided cable Tough braided cable designed to last. ...

Hyper X Alloy FPS keyboards are designed for durability, reliability & high-level play. If a full-sized keyboard is what you need, the Alloy FPS is the right equipment for you. If you’re looking for a tenkeyless (TKL) model that only gives you the most essential keys, the Alloy FPS Pro is the keyboard you need. Each keyboard features everything that a serious FPS player would want out of their keyboard: reliable CHERRY MX key switches, a solid steel frame, detachable cable, Game Mode, 100% Anti-Ghosting & N-key rollover. Whether you’re a pro FPS player, or you just play like one, Hyper X Alloy FPS is the right keyboard for you. Minimalistic compact design ideal for FPS gameplay Maximise your desktop space for quick mouse movement Solid-steel frame Engineered to provide durability & stability. CHERRY MX mechanical key switches for proven reliability Available with CHERRY MX Blue, Brown or Red key switches, giving you proven reliability & the style of switch that fits. Ultra-portable design with detachable cable Reduces storage bulk & potential cable damage. Hyper X red backlit keys with dynamic lighting effects Showcase your style with brilliant backlighting ...