The evolution continues, with the Lian Li O11D EVO PC Case. Taking modular to the next level, this mid-tower chassis can be configured to one of two modes – Normal or Reverse. On top of this, there are multiple positions for I/O panel to be placed, & three orientations for your GPU. Choose from horizontal, vertical, or even upright to fully show off your gaming hardware. Thanks to the mesh panels & spacious interior, airflow has been maximised to the extreme & there is ample support for either Ai O or custom water cooling. Plus, with its intelligent dual-chamber design, cable management is easy & the interior will stay looking sleek. LIAN LI O11D EVO PC CASE BLACK AT A GLANCE: Modular aluminium mesh & tempered glass PC case designed with de 8aur Accommodates up to an E-ATX motherboard Two configuration modes: Normal & Reverse Mode Choose from three GPU positions: standard, vertical*, or upright* Extreme airflow & support for custom water-cooling Can hold up to nine SSDs with included brackets * Require additional hardware. MODULAR TO THE MAX The Lian Li O11D range is known for its modular innovations. The latest O11D EVO takes modularity to the next level. In addition to the easy to remove panels, this mid-tower case can be configured in one of two modes: Normal & Reverse. Whether your desk set-up is skewed to the left or right, you can create the perfect showcase gaming PC. Thanks to the hassle-free design, it only takes a few simple steps to arrange the Lian Li O11D EVO into Reverse Mode. The top & bottom panels can be switched & the whole case flipped, putting your hardware to the left-hand side of the case rather than the traditional right. Creating complete flexibility, there are five accessories available to purchase separately, which support additional options, two of which are panels for the chassis. Firstly, there is a front mesh panel (O11DE-4X) that can be used in lieu of the tempered glass to maximise airflow. There is also a top panel with integrated I/O panel (O11DE-5X), should you keep your PC tower under the desk & require easy access. Further supporting the utmost flexibility, there are three places to install the I/O panel. By default, it is placed between the feet on the bottom of the front panel. Alternatively, the I/O can be installed to the front of the left panel or the rear of the right panel (in Reverse mode). What’s more, there is an additional I/O panel accessory (O11DE-3X) that can be mounted to one of the unused areas alongside the standard panel. This provides an extra three USB (Universal Serial Bus) ports, maximising connectivity. The final two accessories are PCIe riser cables for alternative orientations for your graphics card. FLEXIBLE HARDWARE Thanks to the spacious, dual-chamber interior, the Lian Li O11D EVO PC Case can accommodate for all your gaming hardware in a number of configurations. Able to support up to an E-ATX motherboard, this chassis has 8 expansion slots. With the tempered glass side panel, you can create a truly show-stopping gaming PC. To start with, this chassis

Includes:: an anti-sag bracket & can host a GPU up to 422m long – in one of three positions. In addition to the traditional horizontal configuration, you can install the graphics card vertically or upright. This can be achieved with the vertical (O11DE-1X) & upright (O11DE-2X) PCIe riser cable kits. In the vertical orientation, your GPU can be placed with either a 50mm or 90.5mm clearance from the bottom panel. In either position, there is ample space for Ai O water cooling loops. Opting for the upright GPU fully showcases your high-end hardware, as well as maximising airflow. For holding your extensive gaming library & more, up to nine storage drives can be installed in the Lian Li O11D EVO thanks to the included brackets. You can integrate up to nine SSDs or a combination of six HDDs & three SSDs. This innovative case features mounting points throughout the chassis to create the most comprehensive storage solution. The side drive tray holds either four 2.5” or two 3.5” drives, whilst the cable management bar can host two 2.5” drives, plus a Lian Li & der 8auer plaque! These can both be found in the second, smaller chamber behind the main chamber, along with the drive cage. This can hold either three 2.5” drives or two 3.5” & one 2.5” drive, with the option to mount a 60mm fan to enhance cooling. Lastly, the bottom fan bracket can hold four SSDs or two HDDs within the front chamber. The drive cage & bottom fan bracket do have alternative uses, should nine storage drives be more than you could ever need. The drive cage can double up as a PSU shroud, meaning there is potential for two power supplies to be installed. Models can be up to 220mm in length. Naturally, the bottom fan bracket can be also utilised for your thermal solution, either for fans or a radiator depending on your cooling preference. EXTREME AIRFLOW OR CUSTOM COOLING Keeping your options open, the Lian Li O11D EVO PC Case is compatible with both air & water cooling. Depending on how you configure certain hardware & panels will dictate the best cooling solution for your build. If you opt for the front mesh panel & upright GPU, then the Lian Li O11D EVO is going to have phenomenal airflow. With a fine mesh, these panels have been optimised for thermal performance as well acting as dust filters. The upright GPU allows unprecedented & direct airflow to the graphics card & CPU, that can be further boosted by three 120mm fans. Alternatively, the upright GPU placement also allows for amazing customisation for water cooling. Simpler & more efficient tubing can reach hardware without restriction, which in turn helps the radiators to perform more effectively. Should you prefer vertical or, the more traditional, horizontal mounting, then Ai O cooling is the best option. There is support for three radiators & up to ten fans across the chassis. In both Normal & Reverse modes, up to a 360mm radiator can be mounted on the top, side, & bottom, with the latter two having support for 280mm models, also. Depending on radiator size, up to three 120mm or two 140mm fans can be installed in the same areas, with the tenth being a 120mm fan on the rear. DUAL-CHAMBER, SLEEK INTERIOR Utilising the innovative, dual-chamber design, cable management is incredibly easy within the Lian Li O11D EVO. There is even a cable management bar as part of the second chamber, allowing you to neatly bundle cables together & feed them through the rubber grommets on the separating panel. This chamber features everything you need to keep cables under control, including a hook & ties. Not only does this design keep your PC interior looking sleek, but keeping the PSU separate helps to keep temperatures down. Overall, the Lian Li O11D EVO PC Case has a sleek & modern design. The main structure is manufactured with stainless steel whilst the exterior panelling is either brushed aluminium, mesh, or tinted tempered glass. Contributing to the smooth aesthetic, the power button wraps around two edges of the chassis, whilst the reset & RGB buttons remain on the side. This incredible case is available in three colours, with this model being the black version. Inside & out, this PC case has a classic & iconic look. RGB LED STRIP Completing this versatile case, is an RGB LED strip on the front panel. Simple, yet sophisticated, the Lian Li O11D EVO lighting can be set as one of seven effects, via the “M” button located on the right-side panel. (Or left in Reverse mode.) An eighth lighting mode can be unlocked, via compatible motherboard software or when connected to L-Connect control. This can be achieved with a Lian Li UNI HUB.

...

LIAN LI O11 AIR PC-011 AIR AT A GLANCE Designed with award winning PC modder der 8auer Dual chamber case Excellent airflow properties thanks to support for up to twelve 120mm fans Eye-catching plastic grill front-panel, looks great & offers outstanding cooling Plenty of room for installing storage, can hold up to six 2.5” SSDs or three 3.5” HDDs. THE LIAN LI O11 PC-011 AIR IN DETAIL The Lian Li PC-O11 AIR has been designed with enthusiasts in mind. Lian Li worked with renowned PC modder der 8auer to create a stylish & attractive case that is also optimised for performance. The Lian Li PC-O11 AIR is a tower case & can hold a motherboard up to E-ATX configuration. At its core is a dual chamber enclosure. This helps greatly with cable management & to keep your build neat & tidy. This is particularly useful as Lian Li have included a tempered glass side panel so you can show off your components. The front of the case features a prominent plastic grill that stretches from the front panel to the case's roof. The grill looks great with any LED lighting installed internally being visible & is very practical. It allows for serious airflow with room for up to twelve 120mm fans, which can be distribute across the case's front, bottom & roof panels as well as beside the motherboard. Lian Li have considered the details, they have included two 120mm PWM fans & there is room for multiple storage options such as up to six 2.5” SSDs or three 3.5” HDDs. The front facing I/O panel

Includes:: two USB (Universal Serial Bus) 3.0 Type-A ports & one USB (Universal Serial Bus) 3.1 Type-C port.

...

LIAN LI O11 AIR PC-011 AIR AT A GLANCE Dual chamber case Excellent airflow properties thanks to support for up to twelve 120mm fans Eye-catching plastic grill front-panel, looks great & offers outstanding cooling Plenty of room for installing storage, can hold up to six 2.5” SSDs or three 3.5” HDDs. The Lian Li PC-O11 AIR is a tower case & can hold a motherboard up to E-ATX configuration. At its core is a dual chamber enclosure. This helps greatly with cable management & to keep your build neat & tidy. This is particularly useful as Lian Li have included a tempered glass side panel so you can show off your components. The front of the case features a prominent plastic grill that stretches from the front panel to the case's roof. The grill looks great with any LED lighting installed internally being visible & is very practical. It allows for serious airflow with room for up to twelve 120mm fans, which can be distribute across the case's front, bottom & roof panels as well as beside the motherboard. Lian Li have considered the details, they have included two 120mm PWM fans on the front, plus three 120mm PWM RGB fans internally, plus there is room for multiple storage options such as up to six 2.5” SSDs or three 3.5” HDDs. The front facing I/O panel

Includes:: two USB (Universal Serial Bus) 3.0 Type-A ports & one USB (Universal Serial Bus) 3.1 Type-C port.

...

The Lian Li O11 Dynamic Midi Tower manages to pair 8 mm thick steel with a tinted tempered glass side panel. However Lian Li takes this one step further & succeeds in kitting out the left chamber of the ATX case with a tempered glass front. The right part of the front consists of brushed aluminium & the front panel also hosts a USB (Universal Serial Bus) 3.1 Type-C port, two USB (Universal Serial Bus) 3.0 ports as well as the two obligatory audio jacks. The Lian Li O11 Dynamic Midi Tower can fit an E-ATX motherboard in the left chamber, a graphics card up to 420 mm in length as well as a CPU cooler that is up to 155 mm in height. When it comes to the installation of Ai O- or custom water cooling, the case offers the possibility of installing up to three 360 mm radiators at the same time: On in the top, one at the bottom & one next to the motherboard. To that end the motherboard tray has been angled to the right in comparison to earlier designs. Air inlets are located on the front right hand side of the case. These ensure that heat produced by high-end components is dissipated efficiently & effectively. Naturally the radiator slots can can also be kitted out with fans, each of which are capable of holding up to three 120 mm fans respectively. Several partly rubberised cable guides also come situated near where the motherboard would be in order to ensure neat & tidy cable management. The right hand chamber hosts hardware that produces little heat & therefore requires little additional cooling. The Lian Li O11 Dynamic Midi Tower standards slightly elevated on steel feet with rubberised standoffs to enable cool air to push its way through the bottom of the case which is equipped with dust filters. The chimney principle causes the warm air to rise upwards, whereupon it escapes through the cover which is also equipped with a dust filter. Two additional dust filters cover both perforated grids in the right side section. The elegant Lian Li O11 Dynamic Midi Tower is not merely a feast for the eyes that is easily capable of housing a great deal of gaming hardware, it is also especially suited for PC enthusiasts that want to create custom loops for cooling their hardware. SPACE FOR A SECOND POWER SUPPLY In terms of data storage devices, the case comes with an HDD cage which allows two 3, 5" HDDs to be installed. Both slots can be reached from the rear of the case, & they are concealed behind a perforated panel. Two 2, 5" SSDs can be mounted on the back of the motherboard tray. There are two additional 2, 5" brackets which are screwed to the bottom of the right side panel. In total, two 3, 5"- & four 2, 5" drives can be installed. The HDD cage can also be removed to make space for a second power supply which can also be installed vertically. ...

The Lian Li O11 Dynamic Midi Tower manages to pair 8 mm thick steel with a tinted tempered glass side panel. However Lian Li takes this one step further & succeeds in kitting out the left chamber of the ATX case with a tempered glass front. The right part of the front consists of brushed aluminium & the front panel also hosts a USB (Universal Serial Bus) 3.1 Type-C port, two USB (Universal Serial Bus) 3.0 ports as well as the two obligatory audio jacks. The Lian Li O11 Dynamic Midi Tower can fit an E-ATX motherboard in the left chamber, a graphics card up to 420 mm in length as well as a CPU cooler that is up to 155 mm in height. When it comes to the installation of Ai O- or custom water cooling, the case offers the possibility of installing up to three 360 mm radiators at the same time: On in the top, one at the bottom & one next to the motherboard. To that end the motherboard tray has been angled to the right in comparison to earlier designs. Air inlets are located on the front right hand side of the case. These ensure that heat produced by high-end components is dissipated efficiently & effectively. Naturally the radiator slots can can also be kitted out with fans, each of which are capable of holding up to three 120 mm fans respectively. Several partly rubberised cable guides also come situated near where the motherboard would be in order to ensure neat & tidy cable management. The right hand chamber hosts hardware that produces little heat & therefore requires little additional cooling. The Lian Li O11 Dynamic Midi Tower standards slightly elevated on steel feet with rubberised standoffs to enable cool air to push its way through the bottom of the case which is equipped with dust filters. The chimney principle causes the warm air to rise upwards, whereupon it escapes through the cover which is also equipped with a dust filter. Two additional dust filters cover both perforated grids in the right side section. The elegant Lian Li O11 Dynamic Midi Tower is not merely a feast for the eyes that is easily capable of housing a great deal of gaming hardware, it is also especially suited for PC enthusiasts that want to create custom loops for cooling their hardware. SPACE FOR A SECOND POWER SUPPLY In terms of data storage devices, the case comes with an HDD cage which allows two 3, 5" HDDs to be installed. Both slots can be reached from the rear of the case, & they are concealed behind a perforated panel. Two 2, 5" SSDs can be mounted on the back of the motherboard tray. There are two additional 2, 5" brackets which are screwed to the bottom of the right side panel. In total, two 3, 5"- & four 2, 5" drives can be installed. The HDD cage can also be removed to make space for a second power supply which can also be installed vertically. ...

With the TU150, Lian Li has once again succeeded in combining as many features as possible in a compact Mini-ITX case. But Lian Li didnt neglect the design aspect either. The Lian Li TU150 with its extremely compact

Dimensions of 20.3 x 37.5 x 31.2 cm is particularly easy to transport & therefore has a practical fold-out handle on the top. The side, front, side & top covers made from brushed aluminium are particularly stylish. Overview of the Lian Li TU150A Mini-ITX Case: Case made from brushed aluminium with steel frame Tinted tempered glass side panel Suitable for space-saving SFX or SFX-L power supplies Particularly compact

Dimensions & low weight Carry handle integrated in the top of the case Space for up to two 2.5-inch SSDs or one 3.5-inch HDD & one 2.5-inch SSD Space for 2.5 slot graphics cards up to 320 mm length, CPU cooler up to 165 mm I/O-Panel with 1x USB (Universal Serial Bus) 3.1 Type C, 2x USB (Universal Serial Bus) 3.0 & 1x Audio In/ Out Lian Li TU150A Mini-ITX: High Mobility Thanks to Compact Design Lian Li uses SFX power supplies instead of ATX form factor for the TU150A Mini-ITX case in order to create more space for powerful gaming hardware. The power supply is placed at the top behind the front of the case, with an internal extension cable leading to the rear slot for the power plug. The cable slots protrude to the left & are covered by a metal cover. Lian Li has also prioritised cable management to keep things tidy. There is space for said cables beneath the removable aluminium cover as well as behind the rear wall of the motherboard tray. On the tray itself, users will be pleased to note that Mini-ITX or Mini-DTX format motherboards can be installed. A total of three PCI slot brackets allow the installation of high-end graphics cards with a maximum length of 32 centimeters. Graphics cards can be up to 2.5 slots in width. If fans are installed on the base of the case, this height is reduced to two slots. The horizontal airflow design with the front & rear 120 mm fan slots means that all your installed hardware will be kept perfectly cool. Close-meshed air inlets are integrated into the front cover, these are made from brushed aluminium, & a removable dust filter is fitted in front of the fan slot. in addition, two more fans can be attached to the bottom, allowing waste heat produced by the graphics card to be fed to the outside. Despite the extremely compact design, CPU coolers with a maximum height of 165 millimeters can be accommodated in the Lian Li PC-TU150A. Those who prefer to opt for water cooling will be pleased to note that a 120 mm radiator can be mounted to the rear of the case. Two 2.5-inch storage devices can be installed in the Lian Li PC-TU150A in between the motherboard & the front & in the area above the motherboard. Instead, a 3.5-inch drive can be installed, with the requisite rubber decouplers included in the case. The I/O panel at the front of the top of the case has the obligatory audio connectors & power/reset buttons, a USB (Universal Serial Bus) 3.1 type C & two 3.0 type A ports.



...

The Lian Li TU150 Mini-ITX Case at a Glance: Brushed aluminium case with steel frame Tinted, tempered glass side panel Ultra compact

Dimensions & low weight Carry handle integrated into roof of case Space for up to two 2.5" SSDs or a 3.5" HDD & a 2.5" SSD Space for graphics cards up to 320 mm long, CPU coolers up to 165 mm I/O Panel with 1x USB (Universal Serial Bus) 3.1 Type C, 2x USB (Universal Serial Bus) 3.0 & 1x Audio In/ Out Lian Li TU150 Mini-ITX: High Mobility Thanks to Compact Design Lian Lis TU150 Mini-ITX case uses SFX power supplies instead of ATX power supplies, meaning that the case doesnt have to compromise on powerful gaming hardware. The power supply is installed in the top behind the front section, with an internal extension cable leading to the slot at the back for the plug. The connections for the cables protrude to the left & are cleverly concealed via a metal cover on the tempered glass panel. Lian Li has split up the cable management options as well, with space located beneath a removable aluminium cover as well as the space that has been reserved behind the back wall of the motherboard tray. The motherboard tray supports Mini-ITX- or Mini-DTX format motherboards. A total of three PCI slot brackets enable the installation of high-end graphics cards with a length of up to 32 cm. The horizontal airflow concept with the front & rear 120 mm fan slots helps to cool all installed hardware components sufficiently. Dense-mesh air inlets are integrated into the cases front cover, which made from brushed aluminium, & a removable dust filter is fitted in front of the fan slot. in addition, two more fans can be attached to the underside, which can help to guide excess heat from the graphics card to the outside. Despite the extremely compact design, CPU coolers with a maximum height of 165 millimeters can be accommodated in the Lian Li PC-TU150. Those set on water cooling can attach a 120 mm radiator instead of a fan if preferred. Two 2.5-inch drives can be installed in the Lian Li PC-TU150 between the motherboard & the front as well as in the roof above the mainboard. A 3.5-inch drive can alternatively be installed if needed, & the requisite rubber dampeners are included in the case. The I/O panel at the front of the top has the obligatory audio connectors & power/reset buttons, a USB (Universal Serial Bus) 3.1 type C & two 3.0 type A ports. Technical

Details: Dimensions: 203 x 312 x 375 mm (W x H x D)

Material: Aluminium, steel, tempered glass

Colour: Silver Weight: approx. 4.5kg Form factor: Mini-ITX, Mini-DTX Fan possible: 1x 120 mm (front), 1x 120 mm (back side), 2x 120 mm (floor) Pre-installed: none Dust filter: Front Drives: 1x 2.5 inch (internal, motherboard tray), 1x 3.5/2.5 inch (internal, cover) Expansion slots: 3 Power supply (optional): Standard SFX, /SFX-L I/O Panel: 1x USB (Universal Serial Bus) 3.1 Type C, 2x USB (Universal Serial Bus) 3.0 Type A, 1x per Audio In/ Out Maximum graphics card length: 320 mm Maximum CPU cooler

Height: 165 mm









...

The Lian Li TU150 Mini-ITX Case at a Glance: Black, brushed aluminium case with steel frame Tinted, tempered glass side panel Ultra compact

Dimensions & low weight Carry handle integrated into roof of case Space for up to two 2.5" SSDs or a 3.5" HDD & a 2.5" SSD Space for graphics cards up to 320 mm long, CPU coolers up to 165 mm I/O Panel with 1x USB (Universal Serial Bus) 3.1 Type C, 2x USB (Universal Serial Bus) 3.0 & 1x Audio In/ Out Lian Li TU150 Mini-ITX: High Mobility Thanks to Compact Design Lian Lis TU150 Mini-ITX case uses SFX power supplies instead of ATX power supplies, meaning that the case doesnt have to compromise on powerful gaming hardware. The power supply is installed in the top behind the front section, with an internal extension cable leading to the slot at the back for the plug. The connections for the cables protrude to the left & are cleverly concealed via a metal cover on the tempered glass panel. Lian Li has split up the cable management options as well, with space located beneath a removable aluminium cover as well as the space that has been reserved behind the back wall of the motherboard tray. The motherboard tray supports Mini-ITX- or Mini-DTX format motherboards. A total of three PCI slot brackets enable the installation of high-end graphics cards with a length of up to 32 cm. The horizontal airflow concept with the front & rear 120 mm fan slots helps to cool all installed hardware components sufficiently. Dense-mesh air inlets are integrated into the cases front cover, which made from brushed aluminium, & a removable dust filter is fitted in front of the fan slot. in addition, two more fans can be attached to the underside, which can help to guide excess heat from the graphics card to the outside. Despite the extremely compact design, CPU coolers with a maximum height of 165 millimetres can be accommodated in the Lian Li PC-TU150. Those set on water cooling can attach a 120 mm radiator instead of a fan if preferred. Two 2.5-inch drives can be installed in the Lian Li PC-TU150 between the motherboard & the front as well as in the roof above the mainboard. A 3.5-inch drive can alternatively be installed if needed, & the requisite rubber dampeners are included in the case. The I/O panel at the front of the top has the obligatory audio connectors & power/reset buttons, a USB (Universal Serial Bus) 3.1 type C & two 3.0 type A ports.

...

TU150, Lian Li has once again succeeded in combining as many features as possible in a compact Mini-ITX case. But Lian Li didnt neglect the design aspect either. The Lian Li TU150 with its extremely compact

Dimensions of 20.3 x 37.5 x 31.2 cm is particularly easy to transport & therefore has a practical fold-out handle on the top. The side, front, side & top covers made from brushed aluminium are particularly stylish. Overview of the Lian Li TU150X Mini-ITX Case: Case made from brushed aluminium with steel frame Tinted tempered glass side panel Suitable for space-saving SFX or SFX-L power supplies Particularly compact

Dimensions & low weight Carry handle integrated in the top of the case Space for up to two 2.5-inch SSDs or one 3.5-inch HDD & one 2.5-inch SSD Space for 2.5 slot graphics cards up to 320 mm length, CPU cooler up to 165 mm I/O-Panel with 1x USB (Universal Serial Bus) 3.1 Type C, 2x USB (Universal Serial Bus) 3.0 & 1x Audio In/ Out Lian Li TU150X Mini-ITX: High Mobility Thanks to Compact Design Lian Li uses SFX power supplies instead of ATX form factor for the TU150X Mini-ITX case in order to create more space for powerful gaming hardware. The power supply is placed at the top behind the front of the case, with an internal extension cable leading to the rear slot for the power plug. The cable slots protrude to the left & are covered by a metal cover. Lian Li has also prioritised cable management to keep things tidy. There is space for said cables beneath the removable aluminium cover as well as behind the rear wall of the motherboard tray. On the tray itself, users will be pleased to note that Mini-ITX or Mini-DTX format motherboards can be installed. A total of three PCI slot brackets allow the installation of high-end graphics cards with a maximum length of 32 centimeters. Graphics cards can be up to 2.5 slots in width. If fans are installed on the base of the case, this height is reduced to two slots. The horizontal airflow design with the front & rear 120 mm fan slots means that all your installed hardware will be kept perfectly cool. Close-meshed air inlets are integrated into the front cover, these are made from brushed aluminium, & a removable dust filter is fitted in front of the fan slot. in addition, two more fans can be attached to the bottom, allowing waste heat produced by the graphics card to be fed to the outside. Despite the extremely compact design, CPU coolers with a maximum height of 165 millimeters can be accommodated in the Lian Li PC-TU150X. Those who prefer to opt for water cooling will be pleased to note that a 120 mm radiator can be mounted to the rear of the case. Two 2.5-inch storage devices can be installed in the Lian Li PC-TU150X in between the motherboard & the front & in the area above the motherboard. Instead, a 3.5-inch drive can be installed, with the requisite rubber decouplers included in the case. The I/O panel at the front of the top of the case has the obligatory audio connectors & power/reset buttons, a USB (Universal Serial Bus) 3.1 type C & two 3.0 type A ports.



...

The latest PCIe 4.0 supports transfer rates of 16GT/s bit rate. While providing double the bandwidth of PCIe 3.0, the Gen 4.0 riser cable remains backward compatible with a maximum transfer speed, offers great performance, & shows off the GPU at a great new angle Supports the O11D MINI, O11D & O11D XL ...