The Gigabit PCI Express Adapter is a high performance network adapter that supports advanced management & power savings functionality for system administrators. Full-Duplex technology generates data rates of up to 2 Gbps over a motherboard’s high-speed PCI Express Bus architecture. Jumbo Frame support further optimizes throughput performance. Supports SNMP v 1, Pre-Boot Execution Environment (PXE) 2.1, Remote Program Load (RPL) & Wake-on-LAN (WOL). Optimize network performance with VLAN tagging & Layer 2 Priority Tagging. Optimizes power consumption with advanced Configuration Power Management Interface 2.0 (ACPI) technology. 1 x 10/100/1000 Mbps Auto-MDIX WAN port PCI Express 1.0a compliant Incorporates Advanced Configuration Power Management Interface (ACPI) 2.0 Wake-On-LAN (WOL) TCP segmentation / large send offload IEEE 802.1Q VLAN tagging & IEEE 802.1p Layer 2 priority tagging IEEE 802.3x full-duplex Flow Control Microsoft NDIS5 (IP, TCP, UDP) checksum off-load SNMP v 1 supported Preboot e Xecution Environment (PXE) 2.1 & Remote Program Load (RPL) Jumbo Frames up to 7K Intuitive cable diagnostic utility 3-year Manufacturer limited warranty ...

Splits a networked Po E signal into separate power & Gigabit data sources Network a Power over Ethernet (Po E) Ethernet cable to a non Po E device Network devices at Gigabit speeds all within a compact device Automatically detects Po E terminals & supplies inline power Easily install non-Po E devices where a power outlet is not available Reduce installation & network equipment costs Safeguards network device with short circuit protection Adjustable output DIP switch 5V, 7.5V, 9V, & 12V adjustable output Converts Non-Po E devices with Power Over Ethernet Support Auto-sensing power drawn from 802.3af power source equipment (PSE) devices Supplies power up to 15.5 watts Light weight & compact size ...

This HP compatible Gigabit Copper SFP is engineered by Star Tech.com to deliver what you need most in your network connections: reliable performance. Built to exacting specifications & fully tested to ensure maximum performance, this high-quality SFP transceiver module can be installed into HP networking devices that support the HP JD089B SFP transceiver module, as well as other major brands of networking equipment. The SFP transceiver provides 10 Base-T / 100 Base-TX / 1000 Base-T throughput over a distance of up to 100 m (328 ft.) using a copper RJ-45 connection. It provides a dependable & cost-effective way to add, replace or upgrade a copper Ethernet port on your networking equipment, & its backed by a lifetime warranty. Built for reliable network performance This Gigabit RJ45 copper SFP is manufactured by Star Tech.com to meet or exceed OEM specifications & comply with the industry’s MSA (Multi-Source Agreement) standards. Committed to the highest standards of quality, Star Tech.com provides an extensive range of networking products including copper & fiber network cards, fiber media converters, Ethernet switches & wireless products. Fully compatible with HP & other major brands This Gigabit Copper SFP is engineered to the highest quality standards and is 100% HP compatible, equivalent to the HP JD089B transceiver. The Star Tech.com transceiver is configured & fully tested to ensure it works seamlessly with HP or other major brands of networking equipment. You can be assured that the use of Star Tech.com SFP products should not affect the warranty protection of your networking equipment. Convenient and scalable Delivering both convenience & scalability, this SFP is fully hot-pluggable, which enables you to install it without interrupting network traffic or having to reboot your equipment. It provides a versatile & convenient solution that’s compatible with a multitude of multi & single-port Gigabit Ethernet networking devices. ideal to be used in HP switches, routers & other networking equipment, the SFP provides reliable performance, enabling you to expand your network to remote segments cost-effectively. The SFP supports auto-negotiation, maximum distance of up to 100 m (328 ft.), & maximum data rates of up to 1000 Mbps. ...

This Juniper Networks compatible Gigabit Copper SFP is engineered by Star Tech.com to deliver what you need most in your network connections: reliable performance. Built to exacting specifications & fully tested to ensure maximum performance, this high-quality SFP transceiver module can be installed into Juniper networking devices that support the Juniper EX-SFP-1GE-T SFP, as well as other major brands of networking equipment. The SFP transceiver provides 10 Base-T / 100 Base-TX / 1000 Base-T throughput over a distance of up to 100 m (328 ft.) using a copper RJ-45 connection. It provides a dependable & cost-effective way to add, replace or upgrade a copper Ethernet port on your networking equipment, & its backed by a lifetime warranty. Built for reliable network performance This Gigabit RJ45 copper SFP is manufactured by Star Tech.com to meet or exceed OEM specifications & comply with the industry’s MSA (Multi-Source Agreement) standards. Committed to the highest standards of quality, Star Tech.com provides an extensive range of networking products including copper & fiber network cards, fiber media converters, Ethernet switches & wireless products. Fully compatible with Juniper and other major brands This Gigabit Copper SFP is engineered to the highest quality standards and is 100% Juniper compatible, equivalent to the Juniper EX-SFP-1GE-T transceiver. The Star Tech.com transceiver is configured & fully tested to ensure it works seamlessly with Juniper or other major brands of networking equipment. You can be assured that the use of Star Tech.com SFP products should not affect the warranty protection of your networking equipment. Convenient and scalable Delivering both convenience & scalability, this SFP is fully hot-pluggable, which enables you to install it without interrupting network traffic or having to reboot your equipment. It provides a versatile & convenient solution that’s compatible with a multitude of multi & single-port Gigabit Ethernet networking devices. ideal to be used in Juniper switches, routers & other networking equipment, the SFP provides reliable performance, enabling you to expand your network to remote segments cost-effectively. The SFP supports auto-negotiation, maximum distance of up to 100 m (328 ft.), & maximum data rates of up to 1000 Mbps. ...

3X USB (Universal Serial Bus) power delivery for greater compatibility & extra power for USB (Universal Serial Bus) devices Unique On/ Off Charge delivers the best recharging capability to iPad, iPhone & iPod Touch Next Generation Ultra Durable 2 Classic & 4+1 Phase CPU Power design Supports AMD AM3+ & AM3 Phenom™ II/ Athlon™ II processors Integrated ATI Radeon HD 3000 graphics (Direct X10) Innovative Turbo 3D technology to unleash extra levels of 2D/3D graphics performance PCI-E 2.0 x 16 interface for ultimate graphics performance Hi-def 108d B Signal-to-noise ratio Blu-ray DVD audio playback Hybrid EFI technology with Dual BIOS for 3TB HDD support Integrated DVI interface with HDCP support

Specification
- CPU AM3+ Socket: Support for AMD AM3+ processor Support for AMD AM3 Phenom™ II processor / AMD Athlon™ II processor Hyper Transport Bus 4400 MT/s Chipset North Bridge: AMD 760G South Bridge: AMD SB710 Memory 2 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory (Note 1) Dual channel memory architecture Support for DDR3 1333+ (O.C.)/1066/800 MHz memory modules Onboard Graphics North Bridge: 1 x D-Sub port 1 x DVI-D port, supporting a maximum resolution of 1920x 1200 (Note 2) Audio Realtek ALC889 codec High Definition Audio 2/4/5.1/7.1-channel (Note 3) LAN 1 x Realtek 8111E chip (10/100/1000 Mbit) Expansion Slots 1 x PCI Express x 16 slot, running at x 16 1 x PCI Express x 1 slot (All PCI Express slots conform to PCI Express 2.0 standard.) 1 x PCI slot Storage Interface South Bridge: 6 x SATA 3 Gb/s connectors supporting up to 6 SATA 3 Gb/s devices Support for SATA RAID 0, RAID 1, RAID 10, & JBOD USB South Bridge: Up to 8 USB (Universal Serial Bus) 2.0/1.1 ports (4 on the back panel, 4 via the USB (Universal Serial Bus) brackets connected to the internal USB (Universal Serial Bus) headers) Internal I/O Connectors 1 x 24-pin ATX main power connector 1 x 4-pin ATX 12V power connector 6 x SATA 3 Gb/s connectors 1 x CPU fan header 1 x system fan header 1 x front panel header 1 x front panel audio header 2 x USB (Universal Serial Bus) 2.0/1.1 headers 1 x serial port header 1 x clearing CMOS jumper Back Panel Connectors 1 x PS/2 keyboard port 1 x PS/2 mouse port 1 x D-Sub port 1 x DVI-D port 4 x USB (Universal Serial Bus) 2.0/1.1 ports 1 x RJ-45 port 3 x audio jacks (Line In/ Line Out/ Microphone) I/O Controller ITE IT8720 chip H/W Monitoring System voltage detection CPU/ System temperature detection CPU/ System fan speed detection CPU overheating warning CPU/ System fan fail warning CPU fan speed control (Note 4) BIOS 2 x 16 Mbit flash Use of licensed AWARD BIOS Support for Dual BIOS™ Pn P 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b Unique Features Support for @BIOS Support for Q-Flash Support for Xpress BIOS Rescue Support for Download Center Support for Xpress Install Support for Xpress Recovery 2 Support for Easy Tune (Note 5) Support for Smart Recovery Support for Auto Green Support for On/ Off Charge Support for Cloud OC Support for Q-Share Bundle Software Norton Internet Security (OEM version) Operating System Support for Microsoft Windows 7/ Vista/ XP Form Factor Micro ATX Form Factor; 24.4cm x 20.6cm Note (Note 1) Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of physical memory installed. (Note 2) The DVI-D port does not support D-Sub connector by adapter. (Note 3) To configure 7.1-channel audio, you have to use an HD front panel audio module & enable the multi-channel audio feature through the audio driver. (Note 4) Whether the CPU fan speed control function is supported will depend on the CPU cooler you install. (Note 5) Available functions in Easy Tune may differ by motherboard model.


...

Gigabyte GA-B75TN Socket 1155 HDMI Display Port HD Audio Thin Mini-ITX Motherboard GIGABYTE Thin Mini-ITX Motherboards GIGABYTE Thin-Mini-ITX motherboards are the ideal platform for today’s All-in-One, small form factor & slim profile PCs. Offering a full featured PC experience in a minimal device footprint, GIGABYTE Thin Mini-ITX motherboards are 43% thinner than traditional Mini-ITX designs. Complying with the latest Thin Mini-ITX guidelines, GIGABYTE Thin Mini-ITX motherboards offer additional flexibility making them suited to broad range of innovative PC designs. CPU Support for Intel Core i 7 processors/ Intel Core i 5 processors/ Intel Core i 3 processors/ Intel Pentium processors/ Intel Celeron processors in the LGA1155 package (Supports up to 77W) L3 cache varies with CPU (Some Intel Core processors require a graphic card, please refer "CPU support List" for more information.) Chipset Intel B75 Express Chipset Memory 2 x 1.5V DDR3 SO-DIMM sockets supporting up to 8 GB of system memory * Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed. Dual channel memory architecture Support for DDR3 1600/1333/1066/800 MHz memory modules (Please refer " Memory Support List" for more information.) Onboard Graphics Integrated Graphics Processor: 1 x HDMI 1.3 port, supporting a maximum resolution of 1920x 1200 1 x Display Port, supporting a maximum resolution of 2560x 1600 1 x LVDS connector Audio Realtek ALC887 codec High Definition Audio 2/4/5.1/7.1-channel * To configure 5.1/7.1-channel audio, you have to use an HD front panel audio module & enable the multi-channel audio feature through the audio driver. LAN: 1 x Realtek Gb E LAN chip (10/100/1000 Mbit) Expansion Slots: 1 x PCI Express x 4 slot (Supports 25W only) (The PCIEX4 slot conforms to PCI Express 3.0 standard.) 1 x Mini PCI Express x 1 slot Storage Interface Chipset: 1 x SATA 6 Gb/s connector (SATA0) supporting up to 1 SATA 6 Gb/s device 3 x SATA 3 Gb/s connectors (SATA1/2/3) supporting up to 3 SATA 3 Gb/s devices 1 x m SATA connector USB (Universal Serial Bus) Chipset: Up to 4 USB (Universal Serial Bus) 3.0/2.0 ports on the back panel Up to 5 USB (Universal Serial Bus) 2.0/1.1 ports available through the internal USB (Universal Serial Bus) headers (Card reader/ Touch panel/webcam & other devices) Internal I/O Connectors 1 x 2-pin power connector 1 x CPU fan header 1 x system fan header 1 x SATA 6 Gb/s connector 3 x SATA 3 Gb/s connectors 1 x m SATA connector 1 x SATA power connector 4 x USB (Universal Serial Bus) 2.0/1.1 headers 1 x front panel header 1 x front panel audio header 1 x digital microphone header 1 x AIO speaker header 1 x LVDS connector 1 x LVDS drive voltage header 1 x flat panel display power header (both panel & backlight inverter) 1 x flat panel display power connector 1 x backlight switch header 1 x flat panel display switch header 1 x WIFI activity indicator LED header 1 x Clear CMOS jumper Back Panel Connectors 1 x HDMI port 1 x Display Port 4 x USB (Universal Serial Bus) 3.0/2.0 ports 1 x RJ-45 port 2 x audio jacks (Line Out, Mic In) 1 x DC-In power connector I/O Controller i TE I/O Controller Chip H/W Monitoring System voltage detection CPU/ System temperature detection CPU/ System fan speed detection CPU fan speed control * For 4-pin CPU coolers only. * Whether the CPU fan speed control function is supported will depend on the CPU cooler you install. BIOS 1 x 64 Mbit flash Use of licensed AMI EFI BIOS Pn P 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a Operating System
- Support for Microsoft Windows 8/7 Form Factor
- Thin Mini-ITX Form Factor; 17.0cm x 17.0cm

...

GIGABYTE 3D BIOS (Dual UEFI) All new design of Ultra Durable 4 classic Supports 3rd Gen. Intel 22nm CPUs & 2nd Gen. Intel Core™ CPUs (LGA1155 socket) PCI Express Gen 3.0 support Industrys Leading All Solid Capacitor Design GIGABYTE 333™ Onboard Acceleration (USB 3.0, SATA 3.0 & 3x USB (Universal Serial Bus) Power) Onboard m SATA slot for m SATA SSDs 2-way Cross Fire X™ multi-GPU support HDMI/ DVI interface for smoother HD video playback Enhanced Intel HD Graphics 4000/2500 integrated with the processor GIGABYTE On/ Off Charge™ for USB (Universal Serial Bus) devices

Specification
- CPU Support for Intel Core™ i 7 processors/ Intel Core™ i 5 processors/ Intel Core™ i 3 processors/ Intel Pentium processors/ Intel Celeron processors in the LGA1155 package L3 cache varies with CPU (Some Intel Core™ processors require a graphic card, please refer "CPU support List" for more information.) Chipset Intel H77 Express Chipset Memory 4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory * Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. Dual channel memory architecture Support for DDR3 2200 (OC)/1600/1333/1066 MHz memory modules * To support DDR3 1600 MHz, you must install an Intel 22nm CPU. Support for non-ECC memory modules Support for Extreme Memory Profile (XMP) memory modules * To support XMP memory, you must install an Intel 22nm CPU. (Please refer " Memory Support List" for more information.) Onboard Graphics Integrated Graphics Processor: 1 x D-Sub port 1 x DVI-D port, supporting a maximum resolution of 1920x 1200 * The DVI-D port does not support D-Sub connection by adapter. 1 x HDMI port, supporting a maximum resolution of 1920x 1200 Audio Realtek ALC887 codec High Definition Audio 2/4/5.1/7.1-channel * To configure 7.1-channel audio, you have to use an HD front panel audio module & enable the multi-channel audio feature through the audio driver. Support for S/PDIF Out LAN Atheros Gb E LAN chip (10/100/1000 Mbit) Expansion Slots 1 x PCI Express x 16 slot, running at x 16 (PCIEX16) (The PCIEX16 slot conforms to PCI Express 3.0 standard.) * For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot. * The PCI Express x 16 slot supports up to PCI Express 2.0 standard when an Intel 32nm (Sandy Bridge) CPU is installed. 1 x PCI Express x 16 slot, running at x 4 (PCIEX4) 2 x PCI Express x 1 slots (The PCIEX4 & PCI Express x 1 slots conform to PCI Express 2.0 standard.) 2 x PCI slots Multi-Graphics Technology Support for AMD Cross Fire X™ technology Storage Interface Chipset: 2 x SATA 6 Gb/s connectors (SATA3 0/1) supporting up to 2 SATA 6 Gb/s devices 3 x SATA 3 Gb/s connectors (SATA2 2/3/4) supporting up to 3 SATA 3 Gb/s devices 1 x m SATA connector Support for RAID 0, RAID 1, RAID 5, & RAID 10 * When a RAID set is built across the SATA 6 Gb/s & SATA 3 Gb/s channels, the system performance of the RAID set may vary depending on the devices being connected. USB Chipset: Up to 4 USB (Universal Serial Bus) 3.0/2.0 ports (2 ports on the back panel, 2 ports available through the internal USB (Universal Serial Bus) header) * In Windows XP, the Intel USB (Universal Serial Bus) 3.0 ports can support up to USB (Universal Serial Bus) 2.0 transfer speed. Up to 8 USB (Universal Serial Bus) 2.0/1.1 ports (4 ports on the back panel, 4 ports available through the internal USB (Universal Serial Bus) headers) Internal I/O Connectors 1 x 24-pin ATX main power connector 1 x 4-pin ATX 12V power connector 2 x SATA 6 Gb/s connectors 3 x SATA 3 Gb/s connectors 1 x m SATA connector 1 x CPU fan header 3 x system fan headers 1 x front panel header 1 x front panel audio header 1 x S/PDIF Out header 2 x USB (Universal Serial Bus) 2.0/1.1 headers 1 x USB (Universal Serial Bus) 3.0/2.0 header 1 x Clear CMOS jumper 1 x serial port header 1 x Trusted Platform Module (TPM) header Back Panel Connectors 1 x PS/2 keyboard/mouse port 1 x D-Sub port 1 x DVI-D port 1 x HDMI port 4 x USB (Universal Serial Bus) 2.0/1.1 ports 2 x USB (Universal Serial Bus) 3.0/2.0 ports 1 x RJ-45 port 3 x audio jacks (Line In/ Line Out/ Microphone) I/O Controller i TE I/O Controller Chip H/W Monitoring System voltage detection CPU/ System temperature detection CPU/ System fan speed detection CPU overheating warning CPU/ System fan fail warning CPU/ System fan speed control * Whether the CPU/system fan speed control function is supported will depend on the CPU/system cooler you install. BIOS 2 x 64 Mbit flash Use of licensed AMI EFI BIOS Support for Dual BIOS™ Pn P 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a Unique Features Support for @BIOS Support for Q-Flash Support for Xpress Install Support for Xpress Recovery 2 Support for e Xtreme Hard Drive (X.H.D) Support for Auto Green Support for ON/OFF Charge Support for Q-Share Support for LAN Optimizer (Intelligent optimization network management tool) Operating System Support for Microsoft Windows 8/7/XP Form Factor ATX Form Factor; 30.5cm x 21.5cm


...

Supports 3rd Gen. Intel 22nm CPUs & 2nd Gen. Intel Core™ CPUs (LGA1155 socket) Dual Thunderbolt™ technology support GIGABYTE Ultra Durable™ 5 technology GIGABYTE 3-way Digital Power Engine with GIGABYTE 3D Power GIGABYTE 3D BIOS (Dual UEFI) Onboard m SATA slot for m SATA SSDs PCI Express Gen 3.0 support SLI™ & Cross Fire X™ multi-GPU support Lucid Virtu™ Universal MVP GPU virtualization support High quality 108d B SNR HD audio GIGABYTE On/ Off Charge with 3X USB (Universal Serial Bus) Power

Specification CPU Support for Intel Core™ i 7 processors/ Intel Core™ i 5 processors/ Intel Core™ i 3 processors/ Intel Pentium processors/ Intel Celeron processors in the LGA1155 package L3 cache varies with CPU (Some Intel Core™ processors require a graphic card, please refer "CPU support List" for more information.) Chipset Intel Z77 Express Chipset Memory 4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory * Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. Dual channel memory architecture Support for DDR3 2800 (OC)/1600/1333/1066 MHz memory modules Support for non-ECC memory modules Support for Extreme Memory Profile (XMP) memory modules (Please refer " Memory Support List" for more information.) Onboard Graphics Integrated Graphics Processor: 1 x D-Sub port 1 x DVI-D port, supporting a maximum resolution of 1920x 1200 * The DVI-D port does not support D-Sub connection by adapter. * Simultaneous output for DVI-D & the MDP2 Thunderbolt port is not supported. 1 x HDMI port, supporting a maximum resolution of 1920x 1200 Intel DSL3510L chip: 2 Thunderbolt ports (MDP1/MDP2) support for Mini-Display Port & Thunderbolt monitor (s), & supporting a maximum resolution of 2560x 1600. * When a monitor connected to the DVI-D port, the MDP2 Thunderbolt port can support Thunderbolt storage device (s) only. * Due to PC architecture I/O resources limitation, the amount of the Thunderbolt devices can be used is dependent on the quantity of PCI Express & PCI devices be installed. (Refer to Chapter 1-7, " Back Panel Connectors", & Chapter 2, " Peripherals Intel (R) Thunderbolt" for more information.) Audio Realtek ALC892 codec High Definition Audio 2/4/5.1/7.1-channel Support for S/PDIF Out Support for S/PDIF In LAN 1 x Realtek Gb E LAN chip (10/100/1000 Mbit) Expansion Slots 1 x PCI Express x 16 slot, running at x 16 (PCIEX16) * For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot. 1 x PCI Express x 16 slot, running at x 8 (PCIEX8) * The PCIEX8 slot shares bandwidth with the PCIEX16 slot. When the PCIEX8 slot is populated, the PCIEX16 slot will operate at up to x 8 mode. 1 x PCI Express x 16 slot, running at x 4 (PCIEX4) * The PCIEX4 slot is available only when an Intel 22nm (Ivy Bridge) CPU is installed. * The PCIEX4 slot shares bandwidth with the PCIEX8 & PCIEX16 slots. When the PCIEX4 slot is populated, the PCIEX16 slot will operate at up to x 8 mode & the PCIEX8 will operate at up to x 4 mode. (The PCIEX16, PCIEX8 & PCIEX4 slots conform to PCI Express 3.0 standard.) * Whether PCI Express 3.0 is supported depends on CPU & graphics card compatibility. 3 x PCI Express x 1 slots (The PCIEX1 slot conforms to PCI Express 2.0 standard.) 1 x PCI slot Multi-Graphics Technology Support for AMD Cross Fire X™ / NVIDIA SLI technology Storage Interface Chipset: 2 x SATA 6 Gb/s connectors (SATA3 0/SATA3 1) supporting up to 2 SATA 6 Gb/s devices 4 x SATA 3 Gb/s connectors (SATA2 2~SATA2 5) supporting up to 4 SATA 3 Gb/s devices 1 x m SATA connector * The SATA2 5 connector will become unavailable when the m SATA connector is installed with a solid state drive. Support for RAID 0, RAID 1, RAID 5, & RAID 10 * When a RAID set is built across the SATA 6 Gb/s & SATA 3 Gb/s channels, the system performance of the RAID set may vary depending on the devices being connected. USB Chipset: Up to 4 USB (Universal Serial Bus) 3.0/2.0 ports (2 ports on the back panel, 2 ports available through the internal USB (Universal Serial Bus) headers) * In Windows XP, the Intel USB (Universal Serial Bus) 3.0 ports can support up to USB (Universal Serial Bus) 2.0 transfer speed. Up to 6 USB (Universal Serial Bus) 2.0/1.1 ports (available through the internal USB (Universal Serial Bus) headers) VIA VL800 chip: Up to 4 USB (Universal Serial Bus) 3.0/2.0 ports on the back panel * Due to a Windows 7 limitation, please connect your USB (Universal Serial Bus) device (s) to the USB (Universal Serial Bus) 2.0/1.1 port (s) before the VIA USB (Universal Serial Bus) 3.0 controller driver is installed. Thunderbolt Intel DSL3510L chip: 2 Thunderbolt ports on the back panel Intel Certified Thunderbolt™ Device Internal I/O Connectors 1 x 24-pin ATX main power connector 1 x 8-pin ATX 12V power connector 2 x SATA 6 Gb/s connectors 4 x SATA 3 Gb/s connectors 1 x m SATA connector 1 x CPU fan header 4 x system fan headers 1 x front panel header 1 x front panel audio header 1 x S/PDIF In header 1 x S/PDIF Out header 1 x USB (Universal Serial Bus) 3.0/2.0 header 3 x USB (Universal Serial Bus) 2.0/1.1 headers 1 x serial port header 1 x Clear CMOS jumper 1 x Trusted Platform Module (TPM) header Back Panel Connectors 1 x PS/2 keyboard/mouse port 1 x D-Sub port 1 x DVI-D port 1 x HDMI port 6 x USB (Universal Serial Bus) 3.0/2.0 ports 2 x Thunderbolt ports 1 x RJ-45 port 1 x optical S/PDIF Out connector 5 x audio jacks (Center/ Subwoofer Speaker Out, Rear Speaker Out, Line In, Line Out, Mic In) I/O Controller i TE I/O Controller Chip H/W Monitoring System voltage detection CPU/ System temperature detection CPU/ System fan speed detection CPU overheating warning CPU/ System fan fail warning CPU/ System fan speed control * Whether the CPU/system fan speed control function is supported will depend on the CPU/system cooler you install. BIOS 2 x 64 Mbit flash Use of licensed AMI EFI BIOS Support for Dual BIOS™ Pn P 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a Unique Features Support for @BIOS Support for Q-Flash Support for Xpress Install Support for Xpress Recovery 2 Support for Easy Tune * Available functions in Easy Tune may differ by motherboard model. Support for e Xtreme Hard Drive (X.H.D) Support for Auto Green Support for ON/OFF Charge Support for Q-Share Support for 3D Power Support for EZ Setup Support for Cloud Station Bundle Software Norton Internet Security (OEM version) Intel Smart Response Technology Intel Rapid Start Technology Lucid Logix Virtu MVP * Make sure the monitor cable has been connected to the integrated graphics port on the back panel. Operating System Support for Microsoft Windows 8/7/XP Form Factor ATX Form Factor; 30.5cm x 24.4cm

...

GIGABYTE HD Experience Series Powered by NVIDIA Ge Force GT 630 GPU Integrated with industrys best 2GB DDR3 memory 128-bit memory interface Features Dual link DVI-I/ D-SUB/HDMI with HDCP protection DDR3 2GB edition PCI-E 2.0 interface GIGABYTE UD2 material GIGABYTE custom-designed 80mm fan Support NVIDIA 3D Vision™ Surround Support NVIDIA CUDA™ Technology Support NVIDIA Phy X™ Technology System power supply requirement: 350W

Specification Chipset
- Ge Force GT 630 PCB Form
- ATX Core Clock - 700 MHz Shader Clock
- 1620 MHz Memory Clock
- 1600 MHz Process Technology
- 40 nm Memory Size
- 2048MB Memory Bus
- 128 bit Card Bus
- PCI-E 2.0 Memory Type
- DDR3 Direct X
- 11.1 Open GL
- 4.3 I/O
- HDMI*1, DVI-I*1, D-sub*1 Digital max resolution
- 2560 x 1600 Analog max resolution
- 2048 x 1536 Multi-view
- 2 Card size
- 186 mm x 127 mm x 36 mm Power requirement
- 350W


















...

Supports 6th Generation Intel Core™ Processor Dual Channel DDR3/ DDR3L, 2 DIMMs Audio Noise Guard with High Quality Audio Capacitors HDMI 1.4, D-sub ports for multiple display Realtek Gb E LAN with c Fos Speed Internet Accelerator Software All new GIGABYTE™ APP Center, simple & easy use Support Intel Small Business Basics GIGABYTE 100 series motherboards support the latest 6th Generation Intel Core™ processors, a 14nm desktop CPU which features enhanced performance, power efficiency & support for DDR3/ DDR3L memory, bringing cutting edge features & ultimate performance to your next PC build.

Specification CPU Support for Intel Core i 7 processors/ Intel Core i 5 processors/ Intel Core i 3 processors/ Intel Pentium processors/ Intel Celeron processors in the LGA1151 package L3 cache varies with CPU Chipset Intel H110 Express Chipset Memory 2 x DDR3 DIMM sockets supporting up to 32 GB of system memory * Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed. Dual channel memory architecture Support for DDR3/DDR3L 1600/1333 MHz memory modules Support for ECC UDIMM 1 Rx 8/2 Rx 8 memory modules (operate in non-ECC mode) Support for non-ECC UDIMM 1 Rx 8/2 Rx 8 memory modules Onboard Graphics Integrated Graphics Processor
- Intel HD Graphics support: 1 x D-Sub port, supporting a maximum resolution of 1920x 1200@60 Hz 1 x HDMI port, supporting a maximum resolution of 4096x 2160@24 Hz * Support for HDMI 1.4 version. Audio Realtek ALC887 codec High Definition Audio 2/4/5.1/7.1-channel * To configure 7.1-channel audio, you have to use an HD front panel audio module & enable the multi-channel audio feature through the audio driver. Support for S/PDIF Out Expansion Slots 1 x PCI Express x 16 slot, running at x 16 (The PCI Express x 16 slot conforms to PCI Express 3.0 standard.) 2 x PCI Express x 1 slots (All of the PCI Express x 1 slots conform to PCI Express 2.0 standard.) Storage Interface Chipset:4 x SATA 6 Gb/s connectors USB (Universal Serial Bus) 4 x USB (Universal Serial Bus) 3.0/2.0 ports (2 ports on the back panel, 2 ports available through the internal USB (Universal Serial Bus) header) 6 x USB (Universal Serial Bus) 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB (Universal Serial Bus) headers) Internal I/O Connectors 1 x 24-pin ATX main power connector 1 x 4-pin ATX 12V power connector 4 x SATA 6 Gb/s connectors 1 x CPU fan header 1 x system fan header 1 x front panel header 1 x front panel audio header 1 x S/PDIF Out header 1 x USB (Universal Serial Bus) 3.0/2.0 header 2 x USB (Universal Serial Bus) 2.0/1.1 headers 1 x Trusted Platform Module (TPM) header 1 x Clear CMOS jumper Back Panel Connectors 1 x PS/2 mouse port 1 x PS/2 Keyboard port 1 x D-Sub port 1 x HDMI port 2 x USB (Universal Serial Bus) 3.0/2.0 ports 2 x USB (Universal Serial Bus) 2.0/1.1 ports 1 x RJ-45 port 3 x audio jacks (Line In, Line Out, Mic In)


...