These cutters are used extensively for routing edge moulds face grooves columns fluting water slots engraving & panel moulds in products such as desk tops fire surrounds draining boards & picture frames. These cutters are suitable for use on all natural timbers & man-made boards. TC. 1/2 in Shank R = 12.7 mm. D = 25.4 mm. C = 15.9 mm. ...

Used when machining traditional panels & frame doors. Work formerly done on spindle moulders can now be performed with heavy-duty routers mounted in fixed positions either overhead or inverted. These raised panel cutters run best at lower speeds between 12000 & 18000 rpm & match the Trens range of profile scribers. All are suitable for use on natural timbers & MDF.T.C.T. 1/2 in Shank. D
- 86 mm. C
- 12.7 mm. B
- 12.7 mm. A
- 15.



...

Eccentric single flute cutters. Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Cutters with prefix S are Solid Carbide. Cutters of 2. 0mm diameter & below should have a maximum of 1. 0mm depth of cut per pass. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks. ...

These cutters are suitable for grooving rebating mortising & drilling. The single flute cutters offer fast free cutting. If you require a cleaner cut please use two flute cutters. The depth of cut on cutters of 2.0 mm. diameter & below should be a maximum of 1.0 mm. per pass. Small diameters in Tungsten Carbide must be handled with care to avoid breakage & very shallow passes must be made. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Single flute cutters must not be used in eccentric chucks. Shank. 1/4 in. Dimensions: Shank: 1/4 in. Cutting Diameter (D): 1.5 mm. Cutting Length (C): 6.0 mm. ...

These cutters are suitable for grooving rebating mortising & drilling. The single flute cutters offer fast free cutting. If you require a cleaner cut please use two flute cutters. The depth of cut on cutters of 2.0 mm. diameter & below should be a maximum of 1.0 mm. per pass. Small diameters in Tungsten Carbide must be handled with care to avoid breakage & very shallow passes must be made. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Single flute cutters must not be used in eccentric chucks. Shank. 1/4 in. Dimensions: Shank: 1/4 in. Cutting Diameter (D): 3.2 mm. Cutting Length (C): 8.0 mm. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Two flutes give a clean finish to cut edges. 1/4 in. Shank. C = 11 mm. D = 4.0 mm. 5/32. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Two flutes give a clean finish to cut edges. 1/4 in. Shank. C = 19 mm. D = 6.3 mm. 1/4 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. T.C.T. Tooling 1/2 in Shank. T.C.T. 1/2 in Shank. C = 25 mm. D = 12.7 mm. 1/2 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Two flutes give a clean finish to cut edges. 1/4 in. Shank. C = 25 mm. D = 12.7 mm. 1/2 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. Two flutes give a clean finish to cut edges. 1/4 in. Shank. C = 11 mm. D = 3.2 mm. 1/8 in. ...