Trend dovetail cutters are designed for use with commercial dovetailing & stair housing jigs. Also cutters to produce sliding & lapped dovetails through dovetails & end on dovetails. Suitable for use on natural timbers & man-made boards they are used extensively in cabinet work furniture making stair trenching dovetail jointing & carcass construction. T.C.T.1/4 in. Shank. A = 103 C = 14 mm. D = 13.2 mm. ...

A one-piece tongue & groove set. The parts are inter-changed on the arbor to alter the set up. Maximum timber thickness 22 mm. Minimum timber thickness 15 mm. Instructions for use are supplied. TCT. 1/2 in Shank. Slot Sizes 3.3.5cm. 10 mm. Max depth of slot 9.5 mm. ...

342 Biscuit jointer set enables biscuit jointing with timber man-made fibre & particle board with the router. The set



...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. T.C.T. Tooling 1/2 in Shank. C = 63 mm. D = 15.9 mm. 5/8 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. T.C.T. Tooling 1/2 in Shank. T.C.T. Tooling 1/2 in Shank. C = 25 = 18 mm. 45/64 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. T.C.T. Tooling 1/2 in Shank. C = 25 mm. D = 25.4 mm. 1 in. ...

Two flute straight cutters produce a cleaner finish than the single flute cutters & are suitable for grooving rebating mortising & drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard MDF plywood & certain hardwoods. T.C.T. Tooling 1/2 in Shank. C = 37 mm. D = 25.4 mm. 1 in OL = 66 mm. ...

Profilers with Shank mounted bearings for guidance for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight & curved work. For profiling & rebating applications only. NOT for plunge cutting or grooving. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. A 3 mm. approximate overlap should be left before copy profiling also when using plastic laminate always allow laminate adhesive to dry before trimming. This avoids clogging the guide bearing. Tooling Tungsten Carbide 1/2 in Shank. Angle A = 90 D = 19.1 mm. C = 50 mm. ...

Ovollo & rounding over bearing guided cutters are ideal for curved work they can be used on natural timbers man-made particles & fibre boards. Popular uses include edging window frames glazing bars cabinets table tops pencil rounds trophies shelves & fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings larger bearing removes the quirk producing a round over profile. Tooling: T.C.T. 1/4 in. Shank. R = 3.2 mm. D = 19 mm. C = 9.5 mm. Bearings = 9.5 & 12.7 mm. ...

Ovollo & rounding over bearing guided cutters are ideal for curved work they can be used on natural timbers man-made particles & fibre boards. Popular uses include edging window frames glazing bars cabinets table tops pencil rounds trophies shelves & fire surrounds. They can also be used to produce bullnose edge moulds. All cutters supplied with two bearings larger bearing removes the quirk producing a round over profile. Tooling: T.C.T. 1/4 in. Shank. R = 1.6 mm. D = 15.9 mm. C = 7.9 mm. Bearings = 9.5 & 12.7 mm. ...