Signature SFS01 Massaging Foot Spa Soothe away those aching shopping feet with this luxury massaging foot spa. Sit back, relax ...

The most common microphones used in induction loop systems are 'electret' lecturn, handheld, boundary & lavalier microphones as they have the highest tolerance of magnetic feedback. Best practice (though not always possible) is to place the microphone (s) as close as possible to the speaker. Dynamic microphones should not be used as they contain moving coil magnets which can be affected by the magnetic field generated by the loop. A method that is sometimes suggested for overhead placement is a ceiling-mounted boundary microphone. This should be used with caution as (a) microphone too far from the desired sound source, especially in the case of a high ceiling & (b) the ceiling in buildings of modern construction is often an extremely noisy location due to air handling noise, lighting fixtures & building vibration. Phantom power is provided on all PDA amplifiers so electret microphones with batteries are not necessary. AMT tie/desk mic To avoid interference, microphone cables should be sited at least one metre away from loop cable. ...

Signet APPS Overspill reduction phase shifter. The overspill reduction phase shifter is part of the Outreach range of distributed mixer components. Designed to take the signal from one or more Outreach plates & produce two signals that are 90 degrees out of phase with each other. These signals are then fed into two identical induction loop amplifiers which are in turn connected to two loop patterns which are laid out in a special overlapping design. The resultant magnetic field is evenly spread within the loop but the strength falls off more quickly than outside a simple loop. Features & Specification: Supply voltage: 12-32V DC. Input – balanced/un line: 1V. Bundled items: Instructions & Screws. Actual unit dimensions: 8.5 x 8.5 x 2cm ...

Sig NET recommends all its induction loop systems are tested using a ' Fosmeter Pro' Induction Loop Test Kit (FPROK1).&8200; Designed to simplify the setup of an induction loop system to the latest version of BS EN 60118-4 (Magnetic field strength in audio-frequency induction loops for hearing aid purposes), the kit

Includes:: an FPRO Fosmeter Pro induction loop tester c/w intuitive display & simple to follow test menus, a calibrated signal generator c/w pre-loaded test tones & a set of headphones. As well as checking the magnetic field strength of an induction loop system, it also measures background noise, frequency response, metal compensation & means that you can listen to the loop signal. The tester & signal generator are each powered by a 9V PP3 battery & both are supplied in protective canvas carrying cases. KIT CONTENTS: 1 x Fosmeter Pro (FPRO), 1 x Audio Signal Generator (FPROSG), 2 x Protective pouch, 1 x 32 ohm headphones (HEAD1) for FPRO, 2 x 9 V battery POWER: Internal battery: 1 x 9V&8200;PP3) Battery life: 12 hours approx. Quiescent current: 25m A SIGNAL&8200;PROCESSING: Field Strength Test: Calibration = 400 m A/m (0 d B L); Measurement Scale = <-22 to >+8 d B&8200;L; Frequency = 1 k Hz detection Frequency Response Test: Calibration = 400 m A/m (0 d B&8200;L); Measurement Scale = <-22 to >+8 d B&8200;L; Frequency = 100 Hz / 1 k Hz / 5 k Hz detection Background Noise Test: Calibration = +/-1 d B&8200;L; Measurement Scale = <-42 to >+22d B&8200;L; Frequency = A-weighted detection Metal Compensation Test: Frequency = 3rd octave band 1 k Hz to 8 k Hz OUTPUTS: 3.5m headphone socket suitable for use with HEAD1 headphones (supplied with FPROK kit) CONNECTION&8200;LEADS: AL3 3.5 mm jack to bare ended lead (use to connect to all PDA102 variants / MLK1K / PDA200E amplifier) AL14 3.5 mm jack to XLRM lead (use to connect to a Pro-Range Amplifier).

...

SIGNET RXTI2 Loop Tester Signet Induction Loop Tester. 1 years warranty / Loop Amplifier & accessories. The RXti has been designed to allow installers, & the non-hard of hearing to test & assess the quality & audibility of the loop system. In order to improve the quality of the receiver, it has a dual inductor system which helps reduce the background noise from computer monitors & fluorescent tubes. The audio response from the receiver is flat from 100 Hz to 13 K Hz. The receiver requires a pair of stereo headphones with 3.5mm jack to listen to the audio signal. ...

The Signet PDA 1000/2 professional current mode audio-frequency induction loop amplifier offers outstanding sound quality & unrivalled reliability at a competitive price. The PDA 1000/2 is ideal to be used large rooms up to a maximum of 1000 square metres. The amplifier

Includes:: two XLR connectors- one balanced microphone input & one switchable balanced mic or line level input. Optional 11V phantom power is also available on both inputs to allow the use of condenser microphones. The pre-amplification stage of each amplifier utilises an advanced signal processing system that allows tight control over the audio signal without any degradation of output quality. A metal compensation control is also provided to help offset the frequency response problems associated with the excessive metal content of some rooms. Other features include three level controls (one for each input), a loop drive control, an output current meter & a ‘compression’ activity display giving visible indication of the amplifier’s compressor. The amplifier also features a four-way ‘ Outreach’ input offering full compatibility with Sig NET’s unique Outreach Plate audio input extension system. This system allows the connection of up to 10 additional microphone or line level inputs via a range of specially designed single gang connector plates. Features Ideal for churches, meeting rooms, village halls, classrooms & other applications where finest top quality sound is a must Attractive free-standing design (optional wall & 19” rack-mounting kits available) Two XLR 3 pin input sockets – one balanced mic. & one switchable balanced mic./line Optional 11V phantom power available for electret or condenser microphones ‘ Outreach’ input allows the connection of up to 10 additional mic or line level inputs via a series of separately available single gang connector plates Metal compensation control helps offset the frequency response problems associated with excessive metal in a building True output current meter Visible indication of the amplifier’s compressor action via two LEDs 3.5mm headphone socket allows monitoring of the output signal Advanced audio signal processing with automatic gain control Designed to meet or exceed the requirements of BS7594 and EN60118-4 (when correctly installed) Delivery

Includes:: 1 PDA 1000/2 Audio frequency induction loop amplifier 1 User instructions 1 IEC mains lead



...

Ideal for banks, post offices, small meeting rooms, reception desks, ticket booths & any other application requiring restricted or small area coverage

Includes:: a 3.5mm microphone input (for use with the AMT&8200;microphone supplied) & a line/outreach socket Adjustable drive control allows the amplifier’s output stage to be set-up to suit the exact characteristics of any room State-of-the-art audio processor features an automatic gain control which compensates for poor microphone techniques & helps suppress loud noises, hisses & clicks Designed to be free-standing or wall-mounted using the keyholes provided Meets & exceeds the requirements of BS7594 & EN60118-4 when correctly installed

...

The PDA102R is ideal for small room applications where equipment needs to be mounted above suspended ceilings, etc. Coverage: 50m 2 approx.

Includes:: a 3.5mm microphone input & line/outreach socket. Meets & exceeds the requirements of BS7594 & EN60118-4 when correctly installed. Inputs: 1 x 3.5mm remote mic. socket; 1 x Line/ Outreach socket Indicators: Input level; loop current; power on Controls: Combined input level; loop drive Kit

Includes:: a PDA102 Amplifier, APM Plated microphone, 30m Loop Cable & 'AFILS fitted' sticker.

Dimensions (W x H x D) 136 x 56 x 178mm Weight 1.25kg





...

Can be wall or table mounted Simple installation system Accepts Signet Outreach plates (up to 10 input plates on 1 cable) See related products Comes with microphone & cable included. Complies with DDA legislation BS8300 & also EN60118-4 Ideal for TV lounges, interview rooms, classrooms etc Phantom power for use with other microphones Adjustable limit & drive control. Loop ID sticker Extremely compact design 56mm x 136mm x 175mm 5 year warranty Excellent audio performance Made in UK ...

The PDA200E has revolutionised the induction loop marketplace by bringing the ability to underst&, install & appreciate the technology involved to a whole new client base. Straightforward internal screw connectors & preset controls mean no specialist audio experience or audio connectors are required. By following the simple set-up procedure, no further adjustments are necessary, allowing a finest top quality assistive listening system for the hard of hearing to be set-up in its entirety by new & experienced installers alike. ...