Features: Net Freezer

Volume: 34L Energy Class A/A+ Energy Consumption (k Wh/24h): 0.53/0.42



...

Features: Net Freezer

Volume: 64L Energy Class A/A+ Energy Consumption (k Wh/24h): 0.57/0.45 Climate


...

Signature S434 Nose Trimmer

Features: Precision trimmer with professional rotating microcut stainless steel

...

Signature S435 Mini Shaver

Features: Rechargeable wet & dry cordless shaver Up to 7 days shaving from a single

...

Signature S496 750W Foldable Travel Iron Travel Steam Iron that is ideal for holidays & has a flat folding handle & can be stored easily & it has a push button for steam output.

Features: Variable Temperature Control Vertical Steam Anti-Lime Scale Filter Self Clean Feature Thermostatic Controller 750W Foldable Handle for Easy Storage

...

The most common microphones used in induction loop systems are 'electret' lecturn, handheld, boundary & lavalier microphones as they have the highest tolerance of magnetic feedback. Best practice (though not always possible) is to place the microphone (s) as close as possible to the speaker. Dynamic microphones should not be used as they contain moving coil magnets which can be affected by the magnetic field generated by the loop. A method that is sometimes suggested for overhead placement is a ceiling-mounted boundary microphone. This should be used with caution as (a) microphone too far from the desired sound source, especially in the case of a high ceiling & (b) the ceiling in buildings of modern construction is often an extremely noisy location due to air handling noise, lighting fixtures & building vibration. Phantom power is provided on all PDA amplifiers so electret microphones with batteries are not necessary. AMT tie/desk mic To avoid interference, microphone cables should be sited at least one metre away from loop cable. ...

Signet APPS Overspill reduction phase shifter. The overspill reduction phase shifter is part of the Outreach range of distributed mixer components. Designed to take the signal from one or more Outreach plates & produce two signals that are 90 degrees out of phase with each other. These signals are then fed into two identical induction loop amplifiers which are in turn connected to two loop patterns which are laid out in a special overlapping design. The resultant magnetic field is evenly spread within the loop but the strength falls off more quickly than outside a simple loop. Features & Specification: Supply voltage: 12-32V DC. Input – balanced/un line: 1V. Bundled items: Instructions & Screws. Actual unit dimensions: 8.5 x 8.5 x 2cm ...

Sig NET recommends all its induction loop systems are tested using a ' Fosmeter Pro' Induction Loop Test Kit (FPROK1).&8200; Designed to simplify the setup of an induction loop system to the latest version of BS EN 60118-4 (Magnetic field strength in audio-frequency induction loops for hearing aid purposes), the kit

Includes:: an FPRO Fosmeter Pro induction loop tester c/w intuitive display & simple to follow test menus, a calibrated signal generator c/w pre-loaded test tones & a set of headphones. As well as checking the magnetic field strength of an induction loop system, it also measures background noise, frequency response, metal compensation & means that you can listen to the loop signal. The tester & signal generator are each powered by a 9V PP3 battery & both are supplied in protective canvas carrying cases. KIT CONTENTS: 1 x Fosmeter Pro (FPRO), 1 x Audio Signal Generator (FPROSG), 2 x Protective pouch, 1 x 32 ohm headphones (HEAD1) for FPRO, 2 x 9 V battery POWER: Internal battery: 1 x 9V&8200;PP3) Battery life: 12 hours approx. Quiescent current: 25m A SIGNAL&8200;PROCESSING: Field Strength Test: Calibration = 400 m A/m (0 d B L); Measurement Scale = <-22 to >+8 d B&8200;L; Frequency = 1 k Hz detection Frequency Response Test: Calibration = 400 m A/m (0 d B&8200;L); Measurement Scale = <-22 to >+8 d B&8200;L; Frequency = 100 Hz / 1 k Hz / 5 k Hz detection Background Noise Test: Calibration = +/-1 d B&8200;L; Measurement Scale = <-42 to >+22d B&8200;L; Frequency = A-weighted detection Metal Compensation Test: Frequency = 3rd octave band 1 k Hz to 8 k Hz OUTPUTS: 3.5m headphone socket suitable for use with HEAD1 headphones (supplied with FPROK kit) CONNECTION&8200;LEADS: AL3 3.5 mm jack to bare ended lead (use to connect to all PDA102 variants / MLK1K / PDA200E amplifier) AL14 3.5 mm jack to XLRM lead (use to connect to a Pro-Range Amplifier).

...

SIGNET RXTI2 Loop Tester Signet Induction Loop Tester. 1 years warranty / Loop Amplifier & accessories. The RXti has been designed to allow installers, & the non-hard of hearing to test & assess the quality & audibility of the loop system. In order to improve the quality of the receiver, it has a dual inductor system which helps reduce the background noise from computer monitors & fluorescent tubes. The audio response from the receiver is flat from 100 Hz to 13 K Hz. The receiver requires a pair of stereo headphones with 3.5mm jack to listen to the audio signal. ...

Ideal for banks, post offices, small meeting rooms, reception desks, ticket booths & any other application requiring restricted or small area coverage Requires no specialist audio experience or connectors
- can be fitted by any competent electrician Space-saving double-gang wall-mounting amplifier fits standard UK 25mm back boxes (requires fixed mains wiring) Omni-directional AMT microphone (supplied) plugs directly into 3.5mm socket on the amplifier's front Line/outreach socket also provided (max 3 outreach plates per system) User-adjustable mic. sensitivity & engineer-adjustable loop drive & input level controls Meets & exceeds the requirements of BS7594 & EN60118-4 when correctly installed
...