About Us
Contact Us
Privacy Policy
Cookie Usage
Add Your Store

More From Contributor

Extra Value Micro ATX 400W Fully Wired Efficient Power Supply
Extra Value Micro ATX
400W Fully Wired
Efficient Power Supply
£15.99
Silent PSU with Temperature Control Fan ATX 12V Compliant for all kinds of CPU & mainboard MTBF 50, 000 Hours @ 25 degrees C 2 x SATA Connectors 4 x 4-Pin Molex Connectors PSU Specifications AC INPUT: 230 VAC 4A 50-60 Hz DC +3.3V +5V +12V1 -12V +5VSB Output 18A 17A 20A 0.3A 2A Max 400W Connectors 20+4 Pin Main Connectors:1 4-Pin 12V Connectors:1 SATA Connectors:2 4-Pin Molex Connectors:4 Floppy Drive Connectors:1 Detailed Specifications Dimensions: 125mm x 65mm x 100mm (W x H x D) Input Voltage: 230 VAC Input Current: 4A Input Frequency Range: 50-60 Hz PFC: No Power Good Signal: 150-450 ms Hold Up Time: 1MS-40MS Efficiency: 75% MTBF: 100, 000 Hours Protection: OVP / UVP/ OPP Power: 400W Operation Temperature: 45°C Safety: CE / ROHS Cooling: 8cm Fan Noise: < 17 d BA ...
Available
HyperX 4GB 1600MHz DDR3 CL10 DIMM Fury Series Blue Memory
Hyper X 4GB 1600 M Hz
DDR3 CL10 DIMM Fury
Series Blue Memory
£17.04
SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 48.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 37.5ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 800 M Hz f CK for 1600 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component


...
Available
HyperX 4GB 1600MHz DDR3L CL9 SODIMM 1.35V HyperX Impact Black Series
Hyper X 4GB 1600 M Hz
DDR3L CL9 SODIMM 1.35V
Hyper X Impact Black
Series
£16.98
Hyper X Impact memory boasts the world's fastest SO-DIMM frequency- 2666 M Hz
- to keep you ahead of the curve & level up your
...
Available
HyperX 4GB 1866MHz DDR3 Non-ECC CL9 DIMM XMP HyperX Savage
Hyper X 4GB 1866 M Hz
DDR3 Non-ECC CL9 DIMM
XMP Hyper X Savage
£20.01
Attack the competition with Hyper X Savage memory. Its unique, asymmetrical red heat spreader is made from high-quality aluminum & has a black PCB & a diamond cut finish to make your game shine & help you stand out in the crowd. The heat spreader dissipates heat so your system stays cool & reliable & its low profile fits under oversized CPU coolers. Featuring a design that works well with the latest trends in gaming, Hyper X Savage comes in a wide range of high-performance speeds, from 1600 M Hz to 2400 M Hz, & capacities from 4GB to 8GB in single modules & 8GB to 32GB kits. In CL9-CL11 latencies, it delivers ultra-responsive multitasking & an overall faster system. Dual & quad channel kits are available. Built-in, h&-tuned XMP profiles let users reach higher-performing frequencies, timings & voltages simply by enabling Intel's XMP tool. Even noobs can overclock their platforms with no need for manual adjustments in BIOS. Hyper X Savage is backed by a lifetime warranty & free technical support. ...
Available
HyperX Fury 4GB 1866MHz DDR3 CL10 DIMM Memory
Hyper X Fury 4GB
1866 M Hz DDR3 CL10 DIMM
Memory
£17.99
SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 44.75ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 933 M Hz f CK for 1866 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided componen


...
Available
HyperX Fury Black Series 4GB 1600MHz DDR3 CL10 DIMM Desktop Memory
Hyper X Fury Black
Series 4GB 1600 M Hz
DDR3 CL10 DIMM
Desktop Memory
£20.43
SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 48.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 37.5ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 800 M Hz f CK for 1600 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component


...
Available
HyperX Fury Red 4GB 1600MHz DDR3 CL10 DIMM Memory
Hyper X Fury Red 4GB
1600 M Hz DDR3 CL10 DIMM
Memory
£16.98
SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 48.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 37.5ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 800 M Hz f CK for 1600 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 11, 10, 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component


...
Available
HyperX Fury Series 4GB 1333MHz DDR3 CL9 DIMM Memory
Hyper X Fury Series 4GB
1333 M Hz DDR3 CL9 DIMM
Memory
£16.58
SPECIFICATIONS CL (IDD) 9 cycles Row Cycle Time (t R Cmin) 49.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 36ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 667 M Hz f CK for 1333 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component


...
Available
HyperX Fury White Series 4GB 1333MHz DDR3 CL9 DIMM Memory
Hyper X Fury White
Series 4GB 1333 M Hz
DDR3 CL9 DIMM Memory
£16.08
SPECIFICATIONS CL (IDD) 9 cycles Row Cycle Time (t R Cmin) 49.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 36ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 667 M Hz f CK for 1333 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component


...
Available
Kingston Technology Data Traveler Vault Privacy USB 3.0 Hardware Encrypted 4GB Secure Flash Drive
Kingston Technology
Data Traveler Vault
Privacy USB
3.0 Hardware Encrypted
4GB Secure Flash Drive
£18.98
Kingston's Data Traveler Vault Privacy 3.0 (DTVP 3.0) USB (Universal Serial Bus) Flash drive provides affordable business-grade security with 256-bit AES hardware-based encryption using XTS block cipher mode, which offers stronger protection than CBC & ECB modes. It protects 100 percent of data stored & enforces complex password protection with minimum characteristics to prevent unauthorized access. For additional peace of mind, the drive locks down & reformats after 10 intrusion attempts. It also features a read-only access mode to avoid potential malware risks. Maximum Read Speed 80 MBps Maximum Write Speed 12 MBps Features Password Protection Encryption Support Water Proof Host Interface USB (Universal Serial Bus) 3.0 Form Factor External Height 12.1 mm Width 22.0 mm Length 77.9 mm ...
Available

HyperX Fury Black Series 4GB 1333MHz DDR3 CL9 DIMM Memory

SPECIFICATIONS CL(IDD) 9 cycles Row Cycle Time (tRCmin) 49.125ns (min.) Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin) Row Active Time (tRASmin) 36ns (min.) Maximum Operating Power TBD W* UL Rating 94 V - 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC *Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 667MHz fCK for 1333Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 9, 8, 7, 6 • Programmable Additive Latency: 0, CL - 2, or CL - 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow
seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal(self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component
Buy
Availability: In Stock
£17.50
computer components B2B_2
Description Reviews / Comments Add New

Product Description

SPECIFICATIONS CL (IDD) 9 cycles Row Cycle Time (t R Cmin) 49.125ns (min.) Refresh to Active/ Refresh 260ns (min.) Command Time (t RFCmin) Row Active Time (t RASmin) 36ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to 85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used. FEATURES • JEDEC standard 1.5V (1.425V ~1.575V) Power Supply • VDDQ = 1.5V (1.425V ~ 1.575V) • 667 M Hz f CK for 1333 Mb/sec/pin • 8 independent internal bank • Programmable CAS Latency: 9, 8, 7, 6 • Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock • 8-bit pre-fetch • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] • Bi-directional Differential Data Strobe • Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) • On Die Termination using ODT pin • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C • Asynchronous Reset • PCB: Height 1.180” (30.00mm), single sided component

Reviews/Comments

Add New

Intelligent Comparison

Available
HyperX Fury Black Series 8GB 1333MHz DDR3 CL9 DIMM Memory
HyperX Fury Black Series 8GB 1333MHz DDR3 CL9 DIMM Memory Ebuyer Business
£28.74
Available
HyperX Fury Series 4GB 1333MHz DDR3 CL9 DIMM Memory
HyperX Fury Series 4GB 1333MHz DDR3 CL9 DIMM Memory Ebuyer Business
£16.58
Available
HyperX Fury White Series 4GB 1333MHz DDR3 CL9 DIMM Memory
HyperX Fury White Series 4GB 1333MHz DDR3 CL9 DIMM Memory Ebuyer Business
£16.08
Available
HyperX Fury Black Series 8GB 1333MHz DDR3 CL9 DIMM (Kit of 2)
HyperX Fury Black Series 8GB 1333MHz DDR3 CL9 DIMM (Kit Of 2) Ebuyer Business
£36.68
Available
HyperX Fury Black Series 4GB 1600MHz DDR3 CL10 DIMM Desktop Memory
HyperX Fury Black Series 4GB 1600MHz DDR3 CL10 DIMM Desktop Memory Ebuyer Business
£20.43
Available
HyperX Fury Black 8GB 1600MHz DDR3 CL10 DIMM Memory
HyperX Fury Black 8GB 1600MHz DDR3 CL10 DIMM Memory Ebuyer Business
£30.48
Available
HyperX Fury Black 8GB 1866MHz DDR3 CL10 DIMM Memory
HyperX Fury Black 8GB 1866MHz DDR3 CL10 DIMM Memory Ebuyer Business
£29.64
Available
HyperX Fury Red Series 8GB 1866MHz DDR3 CL10 DIMM Memory
HyperX Fury Red Series 8GB 1866MHz DDR3 CL10 DIMM Memory Ebuyer Business
£27.82

Price History

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

PCB - Printed Circuit Board
OHM - A measure of resistance named after George Simon Ohm
DIMM - Dual In-Line Memory Module
4GB - 4 Gigabytes
Black - A colour which does not emit any colour of the spectrum. Black absorbs all frequencies of the spectrum.
Clock - A device used for telling the time
8-bit - 8 integers or data units. An 8-bit processor can acess 8-bits in a single operation.
Memory - A way to describe the way in which the brain can remember things.

Supplier Information

Ebuyer Business
Get ready to power up your tech game with Ebuyer (https://www.ebuyer.com/)! Explore a vast selection of the latest gadgets, electronics, and computing essentials at unbeatable prices. From cutting-edge laptops and gaming PCs to home appliances and office supplies, we've got everything you need to stay connected and productive. With fast delivery and top-notch customer service, Ebuyer is your go-to destination for all things tech. Don't settle for less shop now and take your tech game to the next level with Ebuyer!
Page Updated: 2024-02-28 09:26:27

Community Generated Product Tags

Oh No! The productWIKI community hasn't generated any tags for this product yet!
Menu