The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The stepper motor with integral stroke/direction end stage is a 42 mm bipolar 2-phase hybrid stepper motor with a step angle of 1.8° (200 steps per revolution). The attainable speed is typically up to 500 rev/min at 24 V operating voltage. Connection is through a JST plug connector, a cable set with open end is included in the delivery. ...

The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The stepper motor with integral stroke/direction end stage is a 42 mm bipolar 2-phase hybrid stepper motor with a step angle of 1.8° (200 steps per revolution). The attainable speed is typically up to 500 rev/min at 24 V operating voltage. Connection is through a JST plug connector, a cable set with open end is included in the delivery. ...

The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The stepper motor with integral stroke/direction end stage is a 42 mm bipolar 2-phase hybrid stepper motor with a step angle of 1.8° (200 steps per revolution). The attainable speed is typically up to 500 rev/min at 24 V operating voltage. Connection is through a JST plug connector, a cable set with open end is included in the delivery. ...

The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The stepper motor with integral stroke/direction end stage is a 42 mm bipolar 2-phase hybrid stepper motor with a step angle of 1.8° (200 steps per revolution). The attainable speed is typically up to 500 rev/min at 24 V operating voltage. Connection is through a JST plug connector, a cable set with open end is included in the delivery. ...

The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The stepper motor with integral stroke/direction end stage is a 42 mm bipolar 2-phase hybrid stepper motor with a step angle of 1.8° (200 steps per revolution). The attainable speed is typically up to 500 rev/min at 24 V operating voltage. Connection is through a JST plug connector, a cable set with open end is included in the delivery. ...

A range of motors with integrated control systems are combined together under the name PANdrive. The combination of a control system with a motor matched to it makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. The two PANdrive types, PD-013-42 (stepper motor with integrated end stage stroke/direction) & PD-110-42 (stepper motor with intelligent control system with serial interface) are 42 mm bipolar 2-phase hybrid stepper motors (or 57 mm with the PD-109-57 types) with a step angle of 1.8° (200 steps per revolution). There are three different motor power specifications available for each. The attainable speeds are typically up to 500 rpm at a 24 V operating voltage. They are connected up using JST plug connectors or for the PD-109-57 types using the screw plug connector supplied. A cable set with open ends is supplied with PD-013-42 and/or PD-110-42. ...

PANdrive ™ denotes a family of motors with integrated electronics. The combination of a control system with matching motor makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. All components presented here are based on a 2-phase high-torque hybrid stepping motor with 1.8 ° step angle (200 steps per revolution). The individual types differ in flange, length, holding torque, interfaces & shaft diameter. The flange level (28, 42, 57, 60 mm) each to be taken from the type designation. Except for the PD-013, which only has a power driver (256 micro steps) with pulse & direction input, all the others are equipped with a motion controller with TMCL ™ & 16 micro steps. The achievable speeds are typically at 500 rpm, whereby the engines with a smaller flange can turn faster than the larger ones. Except for the PD-108, all of PANdrives ™ have the sensor less stall deadlock detection ™ guard. The new sens Ostep™ models (recognizable through
- SE in the type designation) in addition have an integrated absolute encoder for position control. Also available with a CANopen ™ firmware (Ci A 301, 402).
...

PANdrive ™ denotes a family of motors with integrated electronics. The combination of a control system with matching motor makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. All components presented here are based on a 2-phase high-torque hybrid stepping motor with 1.8 ° step angle (200 steps per revolution). The individual types differ in flange, length, holding torque, interfaces & shaft diameter. The flange level (28, 42, 57, 60 mm) each to be taken from the type designation. Except for the PD-013, which only has a power driver (256 micro steps) with pulse & direction input, all the others are equipped with a motion controller with TMCL ™ & 16 micro steps. The achievable speeds are typically at 500 rpm, whereby the engines with a smaller flange can turn faster than the larger ones. Except for the PD-108, all of PANdrives ™ have the sensor less stall deadlock detection ™ guard. The new sens Ostep™ models (recognizable through
- SE in the type designation) in addition have an integrated absolute encoder for position control. Also available with a CANopen ™ firmware (Ci A 301, 402).
...

PANdrive ™ denotes a family of motors with integrated electronics. The combination of a control system with matching motor makes it easy to choose the drive components & makes it possible to build very compact, decentralised solutions. All components presented here are based on a 2-phase high-torque hybrid stepping motor with 1.8 ° step angle (200 steps per revolution). The individual types differ in flange, length, holding torque, interfaces & shaft diameter. The flange level (28, 42, 57, 60 mm) each to be taken from the type designation. Except for the PD-013, which only has a power driver (256 micro steps) with pulse & direction input, all the others are equipped with a motion controller with TMCL ™ & 16 micro steps. The achievable speeds are typically at 500 rpm, whereby the engines with a smaller flange can turn faster than the larger ones. Except for the PD-108, all of PANdrives ™ have the sensor less stall deadlock detection ™ guard. The new sens Ostep™ models (recognizable through
- SE in the type designation) in addition have an integrated absolute encoder for position control. Also available with a CANopen ™ firmware (Ci A 301, 402).
...