ACT-39 Lens plate with M39 thread for ACTUS-B This lens board allows you lenses (Leica thread) are provided with a M39 thread, such as magnifying lenses to use on the ACTUS camera. The surface of the ACT-39 fits the ACTUS-Titanium version. The use of the lenses may possibly be limited to those which can move freely in front of the camera used in each case. ...

This lensplate means that you can mount lenses fitted with a Mamiya RZ/RB bayonet, in combination with the ACTUS view camera. The finish of the ACB-RZ plate matches the ACTUS-B version. The ACB-RZ works with mirrorless as well as DSLR camera bodies for setting at infinity. ...

This lensplate means that you can mount lenses fitted with a Nikon F bayonet, in combination with the ACTUS view camera. The finish of the ACB-NF plate matches the ACTUS-B version. The practical use of lenses may be limited to those that can move freely in front of the bayonet of the used camera body, the ACB-NF only works with mirrorless camera bodies for setting at infinity. ...

The 338 is fitted between tripod & head & is used in combination with tripods that don’t have built-in levelling mechanisms. Its three adjustment dials enable the operator to make fine, finger tip adjustments up to +/- 5 degrees to ensure the camera i attachment: 3/8" female thread attachment type attachment number: 3/8'' screw attachment type bubble spirit level (no.): 1 number

Colour: Black front tilt: -5° / +5° tilt range

Height: 4.00 cm load capacity: 15kg

Material: Aluminum weight: 0.60kg





...

Our innovative system means you can quickly level your photo or video head without needing to make time-consuming adjustments to the length & angle of each single tripod leg attaches by.: 3/8'' screw attachment type bubble spirit level (no.): 1 number

Colour: Black column cross section: three-faceted column travel: 28.00 cm column tube diameter: 28mm half ball diameter: 50.00 mm length: 41.70 cm load capacity: 7kg

Material: aluminum patent: pat. pending weight: 0.67kg



...

Manfrotto Levelling Centre Column for the new 190 series
- 190LC The new Levelling Column allows quick levelling of photo or video
...

The Leveling tripod is the ideal support for fluid heads. It introduces a new degree of integration between head & tripod: the Leveling tripod sets the camera perfectly horizontal while the fluid head allows pan & tilt movements. Recommended for lenses up to 300mm. Series 2 offers an excellent maximum load capacity & a very good torsional rigidity. Available in 3 & 4-section in standard & eye level heights. Gitzo have introduced a new Anti Leg Rotation system, which means the tripod can be opened in less than 15 seconds. Simply loosen all the twist locks on each leg at the same time, then pull the leg down & tighten the locks individually. The system consists of two pins, one fixed & one manually operated by means of a button, that prevent camera equipment from suddenly dropping out of the head when the quick release locking knob is released. Extremely useful with heavy equipment, long lenses & spotting scopes. By fine tuning the freedom of movement of the head, friction control makes the head slower & more precise or faster & looser. This feature also helps to make using heavy equipment or long lenses safer. On ball & fluid head models without separate friction controls, slowly adjusting the lock knobs gives similar results. G-Lock is the new Gitzo leg locking system. The locking mechanism has been completely redesigned in order to achieve a 20% increase in rigidity, faster operation & stronger, safer locking. G-Lock’s special design also provides a “gravity lock” effect: the higher the load applied vertically to the leg, the stronger the lock. GROUND LEVEL SET
- This new feature means that you can remove the center column to save weight & get the camera closer to the ground. Uses existing components: the upper disc with reversible 1/4
- 3/8 bolt & the column hook assembly: Remove column & fix the disk directly to the upper casting using the column hook. No tools needed. HOOK
- This built-in accessory means that you can hang a stabilizingweight (e.g. a full camera bag or a sand/water bag) fromthe bottom of the tripod center column. Useful with longheavy lenses, on uneven ground or in windy conditions. All tripods & monopods in Series 1 & above are provided with removable rubber feet. This feature means that you can easily change worn out rubber feet or to fit other accessories, such as spiked feet or snow/sand shoes. (4 sections tripods in Series 1 are excluded because the final leg section is too narrow to fit these ends). The new leveling system made from three independent leveling bubbles on the quick release plate & one in the ball stem, always guarantee perfectly leveled images. The problem that affects many high quality heads in the market regarding drift angle is absolutely minimized with an outstanding value of 0, 03°. The center column locking collar above the tripod shoulder makes it easier to adjust the column quickly. Series 1 & above are built with an anti-rotation grooved center column for enhanced stability. The rapid column can easily be inverted for an alternative shooting angle or low level macro work. Handles can removed & repositioned or rotated in different positions. This feature greatly increases a head’s versatility & is particularly appreciated by left handed users. Safe Grip is a material that gives a safer lock between your camera & the head plate, preventing the camera from moving or slipping. It is used on quick release plates & in applications where the camera equipment is screwed to the support to reduce pivoting & twisting. Safe Lock is a special techno polymer that maximises locking torque & equipment stabilisation. It is used on the upper discs of tripods & heads, & in applications where the equipment is rotated & screwed onto the support to eliminate micro movements & vibration. When using a ball head, the ability to lock & unlock the panoramic movement independent of front-back or lateral tilt movements is convenient for panoramic photography & when a high level of control is required.


...

Nikon LF-4 Rear Lens Cap. Hard plastic rear lens cap compatible with all NIKKOR lenses. It provides protection against dust, smudges & scratches when not in use. ...

Canon LH-DC70 Lens Hood for the Canon Power Shot G1 X.  Prevents extraneous light outside the angle of view from entering the lens & causing flares or ghosting, which reduce image quality.  Protects the lens from accidental damage. ...

LH-DC80 Maintains image quality by preventing flare, & protects your lens against bumps & knocks. Lens Hood For G1X II. ...