Say hello to FREE Phone Calls!

Yes, the Dynamode DH-005 Stereo Headphone with built in adjustable boom Microphone allows

...

The M-ADSL-Filter has been specifically designed to implement the functionality of a low pass filter using G. Lite Technology. This technology is similar to full rate ADSL but operates at a lower data rate of up to 1.5 Mbps downstream & 512 Kbps upstream, depending on line conditions & lengths. M-ADSL-Filter is a lower speed alternative version of ADSL that will eliminate the need for telecom to install & maintain a premises based POTS splitter. It was found necessary to include one or more, low pass filters in series with the POTS terminals in order to reliably achieve maximum data rates.

For POTS voice band service, the M-ADSLFilter provides protection from ADSL signals, which may impact through non-line or other remote devices (handset, fax, voice band modem etc) & central office operations. For ADSL signals, it also provides protection from the high frequency transient & impedance effect that occur during POTS operations (ringing transients, on-hook, off-hook transient & so on). Because the POTS splitter in the M-ADSL-Filter connects directly to the subscriber loop media, it also provides some protection for externally induced line hits or faults which could damage any attached equipment or endanger people interacting with the installed equipment. The circuit protection will be provided mostly by standard central office line protection means & additional protection measures built into the POTS splitter to protect against line overstress, which could damage the splitter itself.

DC CHARACTERISTICS:
All requirements of this

Specification can be met in the presence of all POTS loop currents from 0 m A to 100 m A. This Single In-Line filter can pass POTS tip-to-ring DC voltages of 0 V to 105 V & ringing signals of 40 Vrms to 150 Vrms at any frequencies from 15.3 Hz to 68 Hz superimposed on DC voltages in the range from 0 V to 105 V. The DC resistance from tip-to-ring at the line port interface with the phone interface shorted, shall be less than or equal to 50 ohms for one filter. The DC resistance from tip-to-ground & from ring-to-ground at the Phone interface with the Line interface open shall be greater than or equal to 10 Megohms. The ground point shall be local building or green wire ground. As an objective, the DC resistance should exceed 10 MW.






...

Got the latest Mobile Phone or Notebook PC & need to transfer your data quickly & easily? Or do you need a Card Reader to support

...

Up to x 10 the speed of USB2.0
- ideal for your intensive storage needs
Enjoy super-fast data
transfer speeds with total
USB2.0



...

Looking for an uncomplicated & quick way to house your existing 2.5-inch SSD or HDD storage device? The new USB3-HD2.5S-SH1 might be just what you are looking for. Unlike conventional disk enclosures, the Dynamode Ready Snap series is tool-less in design, meaning no tiny screws to attach to the drive & no cumbersome connection routines. The Dynamode Ready Snap series is just that! Place your SSD or HDD* in the ABS plastic enclosure & clip down the housing
- that’s it, done in seconds. Technology is not sacrificed for simplicity though. Using the latest USB3 Plug n’ Play technology means you can transfer data up to 5 Gbps & of course being totally backward compatible with USB2 gives total flexibility. Pocket-sized, self-powered by the supplied USB3 cable & cross platform compliance with Windows (tm), Mac (tm)OS X & Linux (tm) means there are no more excuses for not copying your valuable data

Whats in the box:
Caddie
Pouch
Cable
Manual






...

Easily transfer data between multiple Hard Disk formats
Are you looking for a convenient way to transfer precious data from one
...

Looking to add Gigabit Ethernet speed to your USB3 port on a notebookor desktop computer?.
The newly released USB3-CAB-RJ45 Gis
...

Need a quick method to transfer data to & from your existing SATA storage device* such as a HDU or SSD drive?
The new USB3.0-HDK-S-M
...

Looking for a robust andeasy way to house yourexisting 2.5-inch SSD or HDD storage device? The new USB3.1-HD2.5S-M might bejust what you are looking for. Install yourexisting 2.5-inch SATA SSD or HDD*storage device quickly with the piece ofmind of robust protection for your valuabledata. Using the latest USB3.1 (Generation 1) technology keeps the transfer speeds at 5 Gbps but incorporates ‘ Sync-N-Go’ thatreduces a users wait time & bettersignalling than traditional USB3.0 devices. Pocket-sized, self-powered by theintegral USB3/USB3.1 cable & crossplatform compliance with Windows (tm), Mac (tm)OS X & Linux (tm) means thereare no more excuses for not copying yourvaluable data! ...

Do you have more HDMIdevices than you havefree ports on your TV or Monitor? The new LMS Data C-HDMI-31 is alow-cost but highly effective HDMI switchthat means that you can add almost any HDMIinput device such as media centres, Blu Ray (tm), game consoles & muchmore besides. With its highly compact & stylishdesign, totally self-powered via the HDMIcable input signal. The on-board HDMIports are gold plated to aid electricalconduction & help anyone enjoy up to 1080p video & of course HD qualitysound. Installation takes just a few momentsand comes with a supplied infra-redremote control (battery included) whichallows easy HDMI source switching fromthe comfort of your chair. Also bundled isa separate infra-red receiver module sothere is no more frustration about trying toswitch HDMI channels, like on some otherlesser HDMI switch brands. The C-HDMI-31 is also at home with HDMI computer switching & is perfectfor users of multiple HDMI sources such as Macs, PCs & other HDMI devices thatneed to share a single HDMI readymonitor. ...