A low-cost way to use your existing hard disk from your old laptop or PC, the USB (Universal Serial Bus)-HD2.5SI enclosure is

...

**UNBELIEVABLE DEAL ON THIS EXTRA LONG 5M PREMIUM BRAIDED CABLE**


Strive for image perfection. For less.
Do you wish



...

The M-ADSL-Filter has been specifically designed to implement the functionality of a low pass filter using G. Lite Technology. This technology is similar to full rate ADSL but operates at a lower data rate of up to 1.5 Mbps downstream & 512 Kbps upstream, depending on line conditions & lengths. M-ADSL-Filter is a lower speed alternative version of ADSL that will eliminate the need for telecom to install & maintain a premises based POTS splitter. It was found necessary to include one or more, low pass filters in series with the POTS terminals in order to reliably achieve maximum data rates.

For POTS voice band service, the M-ADSLFilter provides protection from ADSL signals, which may impact through non-line or other remote devices (handset, fax, voice band modem etc) & central office operations. For ADSL signals, it also provides protection from the high frequency transient & impedance effect that occur during POTS operations (ringing transients, on-hook, off-hook transient & so on). Because the POTS splitter in the M-ADSL-Filter connects directly to the subscriber loop media, it also provides some protection for externally induced line hits or faults which could damage any attached equipment or endanger people interacting with the installed equipment. The circuit protection will be provided mostly by standard central office line protection means & additional protection measures built into the POTS splitter to protect against line overstress, which could damage the splitter itself.

DC CHARACTERISTICS:
All requirements of this

Specification can be met in the presence of all POTS loop currents from 0 m A to 100 m A. This Single In-Line filter can pass POTS tip-to-ring DC voltages of 0 V to 105 V & ringing signals of 40 Vrms to 150 Vrms at any frequencies from 15.3 Hz to 68 Hz superimposed on DC voltages in the range from 0 V to 105 V. The DC resistance from tip-to-ring at the line port interface with the phone interface shorted, shall be less than or equal to 50 ohms for one filter. The DC resistance from tip-to-ground & from ring-to-ground at the Phone interface with the Line interface open shall be greater than or equal to 10 Megohms. The ground point shall be local building or green wire ground. As an objective, the DC resistance should exceed 10 MW.






...

The new standard in performance
headphones for business and
pleasure.

The exciting Dynamode MX-878 surround sound headphones



...

SATA to ESATA USB (Universal Serial Bus) HDD Docking Station with one touch back up button. all in one, stylish & easy to use Desktop design!


Features:
E-SATA HDD Docking Station
Standable, convenient & Trendy Design
SATA I, & SATA II Compatible
SATA II Transfer Rate Up to 3GB/s, USB (Universal Serial Bus) 2.0: Up to 480 Mbps
Supports all 2.5"/3.5" SATA Hard Disk Drive of any capacity
Supports e SATA Transfer Speed up to 3 Gbps
Supports USB (Universal Serial Bus) 2.0 Transfer Speed up to 480 Mbps
One Touch Backup function
Plugs & plays & is hot-swappable
Power LED indicator


INTERFACE:
One Touch Backup function
Plugs & plays & is hot-swappable
Power LED indicator


















...

The M-ADSL-Filter has been specifically designed to implement the functionality of a low pass filter using G. Lite Technology. This technology is similar to full rate ADSL but operates at a lower data rate of up to 1.5 Mbps downstream & 512 Kbps upstream, depending on line conditions & lengths. M-ADSL-Filter is a lower speed alternative version of ADSL that will eliminate the need for telecom to install & maintain a premises based POTS splitter. It was found necessary to include one or more, low pass filters in series with the POTS terminals in order to reliably achieve maximum data rates.

For POTS voice band service, the M-ADSLFilter provides protection from ADSL signals, which may impact through non-line or other remote devices (handset, fax, voice band modem etc) & central office operations. For ADSL signals, it also provides protection from the high frequency transient & impedance effect that occur during POTS operations (ringing transients, on-hook, off-hook transient & so on). Because the POTS splitter in the M-ADSL-Filter connects directly to the subscriber loop media, it also provides some protection for externally induced line hits or faults which could damage any attached equipment or endanger people interacting with the installed equipment. The circuit protection will be provided mostly by standard central office line protection means & additional protection measures built into the POTS splitter to protect against line overstress, which could damage the splitter itself.

DC CHARACTERISTICS:
All requirements of this

Specification can be met in the presence of all POTS loop currents from 0 m A to 100 m A. This Single In-Line filter can pass POTS tip-to-ring DC voltages of 0 V to 105 V & ringing signals of 40 Vrms to 150 Vrms at any frequencies from 15.3 Hz to 68 Hz superimposed on DC voltages in the range from 0 V to 105 V. The DC resistance from tip-to-ring at the line port interface with the phone interface shorted, shall be less than or equal to 50 ohms for one filter. The DC resistance from tip-to-ground & from ring-to-ground at the Phone interface with the Line interface open shall be greater than or equal to 10 Megohms. The ground point shall be local building or green wire ground. As an objective, the DC resistance should exceed 10 MW.






...

Got the latest Mobile Phone or Notebook PC & need to transfer your data quickly & easily? Or do you need a Card Reader to support

...

Up to x 10 the speed of USB2.0
- ideal for your intensive storage needs
Enjoy super-fast data
transfer speeds with total
USB2.0



...

Looking for an uncomplicated & quick way to house your existing 2.5-inch SSD or HDD storage device? The new USB3-HD2.5S-SH1 might be just what you are looking for. Unlike conventional disk enclosures, the Dynamode Ready Snap series is tool-less in design, meaning no tiny screws to attach to the drive & no cumbersome connection routines. The Dynamode Ready Snap series is just that! Place your SSD or HDD* in the ABS plastic enclosure & clip down the housing
- that’s it, done in seconds. Technology is not sacrificed for simplicity though. Using the latest USB3 Plug n’ Play technology means you can transfer data up to 5 Gbps & of course being totally backward compatible with USB2 gives total flexibility. Pocket-sized, self-powered by the supplied USB3 cable & cross platform compliance with Windows (tm), Mac (tm)OS X & Linux (tm) means there are no more excuses for not copying your valuable data

Whats in the box:
Caddie
Pouch
Cable
Manual






...

High-density USB3.0 connectivity is now
within your reach.
Looking to move up & take advantage of up to ten times the speed

...