United Kingdom
France
Germany
Netherlands
Sweden
USA
Italy
Spain
More From Contributor
Dynamode Tailed Microfilter & Splitter For ADSL Lines
The M-ADSL-Filter has been specifically designed to implement the functionality of a low pass filter using G.Lite Technology. This technology is similar to full rate ADSL but operates at a lower data rate of up to 1.5Mbps downstream and 512Kbps upstream, depending on line conditions and lengths. M-ADSL-Filter is a lower speed alternative version of ADSL that will eliminate the need for telecom to install and maintain a premises based POTS splitter. It was found necessary to include one or more, low pass filters in series with the POTS terminals in order to reliably achieve maximum data rates.
For POTS voice band service, the M-ADSLFilter provides protection from ADSL signals, which may impact through non-line or other remote devices (handset, fax, voice band modem etc) and central office operations. For ADSL signals, it also provides protection from the high frequency transient and impedance effect that occur during POTS operations (ringing transients, on-hook, off-hook transient and so on). Because the POTS splitter in the M-ADSL-Filter connects directly to the subscriber loop media, it also provides some protection for externally induced line hits or faults which could damage any attached equipment or endanger people interacting with the installed equipment. The circuit protection will be provided mostly by standard central office line protection means and additional
protection measures built into the POTS splitter to protect against line overstress, which could damage the splitter itself.
DC CHARACTERISTICS:
All requirements of this specification can be met in the presence of all POTS loop currents from 0 mA to 100 mA. This Single In-Line filter can pass POTS tip-to-ring DC voltages of 0 V to 105 V and ringing signals of 40 Vrms to 150 Vrms at any frequencies from 15.3 Hz to 68 Hz superimposed on DC voltages in the range from 0 V to 105 V. The DC resistance from tip-to-ring at the line port interface with the phone interface shorted, shall be less than or equal to 50 ohms for one filter. The DC resistance from tip-to-ground and from ring-to-ground at the Phone interface with the Line interface open shall be greater than or equal to 10 Megohms. The ground point shall be local building or green wire ground. As an objective, the DC resistance should exceed 10 MW.
For POTS voice band service, the M-ADSLFilter provides protection from ADSL signals, which may impact through non-line or other remote devices (handset, fax, voice band modem etc) and central office operations. For ADSL signals, it also provides protection from the high frequency transient and impedance effect that occur during POTS operations (ringing transients, on-hook, off-hook transient and so on). Because the POTS splitter in the M-ADSL-Filter connects directly to the subscriber loop media, it also provides some protection for externally induced line hits or faults which could damage any attached equipment or endanger people interacting with the installed equipment. The circuit protection will be provided mostly by standard central office line protection means and additional
protection measures built into the POTS splitter to protect against line overstress, which could damage the splitter itself.
DC CHARACTERISTICS:
All requirements of this specification can be met in the presence of all POTS loop currents from 0 mA to 100 mA. This Single In-Line filter can pass POTS tip-to-ring DC voltages of 0 V to 105 V and ringing signals of 40 Vrms to 150 Vrms at any frequencies from 15.3 Hz to 68 Hz superimposed on DC voltages in the range from 0 V to 105 V. The DC resistance from tip-to-ring at the line port interface with the phone interface shorted, shall be less than or equal to 50 ohms for one filter. The DC resistance from tip-to-ground and from ring-to-ground at the Phone interface with the Line interface open shall be greater than or equal to 10 Megohms. The ground point shall be local building or green wire ground. As an objective, the DC resistance should exceed 10 MW.
Product Description
Reviews/Comments
Add New
Vouchers
No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.
Denmark