There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Either Hot forged or CNC'd from sizes 1 to 6 keep strength high and weight to a minimum- Extruded bar used on sizes 7 to 11 to reduce weight- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 7: Colour: Grey. Strength: 12kn. Weight: 40gSize 8: Colour: Turquoise. Strength: 12kn. Weight: 45gSize 9: Colour: Gold. Strength: 12kn. Weight: 50gThese wallnuts are sold separately
There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Either Hot forged or CNC'd from sizes 1 to 6 keep strength high and weight to a minimum- Extruded bar used on sizes 7 to 11 to reduce weight- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 1: Colour: Pink. Strength: 7kn/4kn. Weight: 15gSize 2: Colour: Green. Strength: 9kn. Weight: 26gSize 3: Colour: Silver. Strength: 11kn. Weight: 28gThese wallnuts are sold separately
There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Either Hot forged or CNC'd from sizes 1 to 6 keep strength high and weight to a minimum- Extruded bar used on sizes 7 to 11 to reduce weight- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 4: Colour: Gold. Strength: 12kn. Weight: 30gSize 5: Colour: Blue. Strength: 12kn. Weight: 32gSize 6: Colour: Red. Strength: 12kn. Weight: 39gThese wallnuts are sold separately
There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 00: Colour: Gold. Strength: 2kn. Weight: 6gSize 0: Colour: Blue. Strength: 2kn. Weight: 6gSize 0.5: Colour: Red. Strength: 4kn. Weight: 9gSize 0.75: Colour: Silver. Strength: 6kn. Weight: 10gThese wallnuts are sold separately
There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Either Hot forged or CNC'd from sizes 1 to 6 keep strength high and weight to a minimum- Extruded bar used on sizes 7 to 11 to reduce weight- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 10: Colour: Silver. Strength: 12kn. Weight: 56gSize 11: Colour: Green. Strength: 12kn. Weight: 68gThese wallnuts are sold separately
There are lots of nuts on the market, but Wallnuts are amongst the best because of their design, the materials that they are made from and the attention to detail that goes into their manufacture. Features:- Complex 3D curves and scallops means secure and fast placement in all rock types- DMMs accurate heat treatment processes on specifically chosen alloys maximises bite- Counter sunk and drilled out all the radiuses to avoid stress points where the wire enters the nut- Rumbled well to remove sharp edges that can hinder placement- Full size crimp because this is critical to safety- Double sealed label upside down for ease of identification- Joint collaboration with Wild Country to standardise colour recognitionSize 1: Colour: Pink. Strength: 7kn/4kn. Weight: 15gSize 2: Colour: Green. Strength: 9kn. Weight: 26gSize 3: Colour: Silver. Strength: 11kn. Weight: 28gSize 4: Colour: Gold. Strength: 12kn. Weight: 30gSize 5: Colour: Blue. Strength: 12kn. Weight: 32gSize 6: Colour: Red. Strength: 12kn. Weight: 39gSize 7: Colour: Grey. Strength: 12kn. Weight: 40gSize 8: Colour: Turquoise. Strength: 12kn. Weight: 45gSize 9: Colour: Gold. Strength: 12kn. Weight: 50gSize 10: Colour: Silver. Strength: 12kn. Weight: 56gSize 11: Colour: Green. Strength: 12kn. Weight: 68gThese wallnuts are sold as a set
This rack updates the classic brake bar descender. The design and configuration of the bars makes it easy to set up and insert the rope. Compact and lightweight, the device allows the user to adjust the amount of friction during the descent to adapt to changing conditions (rope weight, terrain, etc.).The number of bars engaged on the rope may be adjusted at any time to obtain the desired amount of frictionGood distribution of friction and heat helps preserve the ropeDoes not twist the rope
In order to provide more racking options in DMM's active protection range they combined some of the favourite features from our two existing cams: the tried and trusted 13.75, single axle head unit of the 4CU, with the justifiably popular stem assembly of the Dragon with its patented thumb press and extendable sling design. The result is a lightweight, versatile, and functional device that caters for climbers who prefer single stem ergonomics, for those who are used to our traditional sizing system, and for those who want to double up their cam racks to offer even more placement options. The range covers placements from 13mm to 100mm in nine colour coded sizes. The colours follow the same sequence as the 4CU, but they have reversed the cam lobe colouring to the opposite to the Dragon for easily identification. Features A lightweight single axle, single stem cam Special thumb grip and trigger bar for easy handling Original 13.75 camming angle Cam stops for 10kN in passive position Fitted with extendable 8mm Dyneema slings Colour coded to help you make a speedy identification Red: Demon Cam 0.5 Silver: Demon Cam 1.5 Gold: Demon Cam 2.5
Black Diamonds best-selling and most trusted camming device, the Camalots' double-axle design offers a much larger range for each cam unit compared to traditional single-axle units. Because loading forces are shared between both axles, this design has the strength to work as a full-strength cam stop, allowing the cam to function as passive pro if it walks back into a wider part of a crack and umbrellas. In addition, they feature an C-Loop continuous cable stem design that is strong and durable, and they are colour-coded for easy identification. Finally, the triggers and cable loops are easy to grab, and the slings are large enough to manipulate with gloves on.
The Petzl crevasse rescue kit contains everything needed for setting up a hauling system or a rope ascent in case of a fall into a crevasse. It has 1 mini traxion pulley, 2 ok screwlock carabiners, 1 tibloc, 1 oscillante pulley and a 120cm St'Anneau sling.
Each cam is rated to 14 kN in the active, working position with the quick release sling doubled, and 12 kN with sling fully extended. The passive strength of the cams, resting on their stops, is 10 kN.The cam lobes are cut to a 13.75 spiral. This has proven to be the best angle for balancing a cam's range and holding power. DMM's cam lobes are anodized for easy, size identification on the rack. * Please note cams sold separately.
Black Diamonds best-selling and most trusted camming device, the Camalots' double-axle design offers a much larger range for each cam unit compared to traditional single-axle units. Because loading forces are shared between both axles, this design has the strength to work as a full-strength cam stop, allowing the cam to function as passive pro if it walks back into a wider part of a crack and umbrellas. In addition, they feature an C-Loop continuous cable stem design that is strong and durable, and they are colour-coded for easy identification. Finally, the triggers and cable loops are easy to grab, and the slings are large enough to manipulate with gloves on.
Each cam is rated to 14 kN in the active, working position with the quick release sling doubled, and 12 kN with sling fully extended. The passive strength of the cams, resting on their stops, is 10 kN.The cam lobes are cut to a 13.75 spiral. This has proven to be the best angle for balancing a cam's range and holding power. Our cam lobes are anodized for easy, size identification on the rack. After all, time is of the essence when you're on a pumpy route.* Please note cams sold separately.
Immaculate Marginal Protection or I.M.P's are micro wires machined from silicon bronze and silver soldered on stainless wire. The wires benefit from a colour coded aluminium swage/keeper, which aids selection and helps load the unit evenly.Size 2: Colour: Red. Strength: 5kn. Weight: 8gSize 3: Colour: Silver. Strength: 5kn. Weight: 10gSize 4: Colour: Purple. Strength: 7kn. Weight: 13gThese IMP's are sold as a set
Each cam is rated to 14 kN in the active, working position with the quick release sling doubled, and 12 kN with sling fully extended. The passive strength of the cams, resting on their stops, is 10 kN.The cam lobes are cut to a 13.75 spiral. This has proven to be the best angle for balancing a cam's range and holding power. DMM's cam lobes are anodized for easy, size identification on the rack. * Please note cams sold separately.
The Metolius Contact is the most deluxe, full-featured training board to date with an amazing variety of holds and new, ergonomic variable width pinches. Please note this is available in asorted colours, you may not receive the colour pictured. Features CAD/CAM designed master for perfect symmetry Ergonomically curved for less joint stress and reduced injuries 11 pockets to choose from (2, 3, 4 fingers - tips to 2nd joint) 4 central edges from shallow to deep Top mounted pull-up jugs, rounded and flat slopers Fine grained texture is skin-friendly Includes comprehensive mounting instructions, training guide and mounting hardware 826 mm x 279 mm x 67 mm
Immaculate Marginal Protection or I.M.P's are micro wires machined from silicon bronze and silver soldered on stainless wire. The wires benefit from a colour coded aluminium swage/keeper, which aids selection and helps load the unit evenly.Size 1: Colour: Blue. Strength: 4kn. Weight: 4gSize 2: Colour: Red. Strength: 5kn. Weight: 8gSize 3: Colour: Silver. Strength: 5kn. Weight: 10gSize 4: Colour: Purple. Strength: 7kn. Weight: 13gSize 5: Colour: Green. Strength: 7kn. Weight: 16gThese nuts are sold as a set
Designed for Alpine climbing. The Onda pitons are designed to fit a wide variety of crack widths, made of nickel chromolly steel for the ultimate in durability. To alleviate the problem of sharp edges damaging alloy carabiners the stamped eye is reinforced with a stainless steel grommet which prevents the piton from cutting into the carabiner in the event of a fall.
The Nutbuster is the perfect tool for removing those jammed nuts. The wide rubebr handle makes it easy to hold and preventing the metal digging into your hand. The rubber can be removed to reveal a 17mm spanner which cann be used for tightening those loose bolts. Features Rubber handled nut key Laser cut from stainless steel Lightening holes to reduce weight Narrow profile to access deep placements 10mm spanner inside handle
The Petzl Croll Chest Ascender is unmatched for efficiency on fixed lines. Compact and lightweight, it does not interfere with progression. The stainless steel wear plate improves durability by reinforcing the rope friction zone. Features Used with a BASIC ascender or with an ASCENSION handled ascender for rope ascents Toothed cam with self-cleaning slot optimizes performance under any conditions (e.g. frozen or dirty ropes) Stainless steel cam has better resistance to corrosion Stainless steel wear plate for improved durability Open the catch by pinching for simple, quick manipulation Lower hole angled to keep the CROLL chest ascender flat Upper hole for attaching a TORSE shoulder strap and keeping the ascender in position Material(s): aluminum for the frame, stainless steel for the cam, nylon for the trigger Weight: 90g Rope: for use with single ropes between 8 and 11 mm
The DMM Bug is a classic belay device that is happiest handling ropes from 9 to 11mm. It's hot forged, rumbled and anodised to give kind rope bearing surfaces and has a hard wearing nylon coated wire to stop it escaping.Features:Hot Forged and fully Heat TreatedGood with larger ropesAnodised for corrosion resistance
Used below the rappel device, the SHUNT works as a rappel back-up and replaces self-jamming knots like the Prusik. Works on single and double ropes.Easy to install on the ropeSmooth clamping surfaces won't damage ropeMay be used to ascend single or doubled rope.
The Petzl Croll was originally developed for caves, and mounts between the seat harness and chest strap. The angled attachment hole keeps it properly aligned on the chest, while the chrome-plated steel cam with angled teeth and a self-cleaning slot grips ropes even in muddy or icy conditions. Not designed for self-belaying.
One of the most popular devices for cave descents worldwide. Offers exceptional control and versatility, while the self-braking function facilitates on-rope manoeuvres.Self-braking function allows you to easily stop and maintain your position on ropeDevice can be rapidly installed or removed from the rope without disconnecting it from the harnessMay also be used to ascend short distances with the addition of an ascender and foot loop
The GRIGRI 2 belay device with assisted braking is designed to facilitate belay maneuvers. The GRIGRI 2 works equally well for lead climbing and top roping. It may be used on all single dynamic 8.9 to 11 mm ropes on the market (ideal at 9.4 mm to 10.3 mm). Both compact and ultra-light, the GRIGRI 2 will accompany you on climbs around the world for many years. The GRIGRI 2 has a new design that allows excellent control during the descent.
The Black Diamond ATC XP is a true variable-friction device that maintains the silky-smooth feeding of the ATC but ups the braking power thanks to it's grooved rope slots. A super versatile device, it is ideal for all styles of climbing with ropes 7.7 to 11 mm and has features such as a high friction mode offering 3 times greater hold and stopping power, and a geometric fluid design that reduces rope kinking.
Classic pitons for thinner cracks, Knifeblades have precision-ground blades for a consistent taper and a hole in the thickest part of the head to reduce weight without sacrificing durability. Features 2 clip-ins for corner placements and weight reduction
Classic big brother of the Knifeblade, Black Diamond Bugaboos, have precision-ground blades for a consistent taper and a hole in the thickest part of the head to reduce weight without sacrificing durability. Features 2 clip-ins for corner placements and weight reduction
Classic big brother of the Knifeblade, Black Diamond Bugaboos, have precision-ground blades for a consistent taper and a hole in the thickest part of the head to reduce weight without sacrificing durability. Features 2 clip-ins for corner placements and weight reduction
Black Diamonds best-selling and most trusted camming device, the Camalots' double-axle design offers a much larger range for each cam unit compared to traditional single-axle units. Because loading forces are shared between both axles, this design has the strength to work as a full-strength cam stop, allowing the cam to function as passive pro if it walks back into a wider part of a crack and umbrellas. In addition, they feature an C-Loop continuous cable stem design that is strong and durable, and they are colour-coded for easy identification. Finally, the triggers and cable loops are easy to grab, and the slings are large enough to manipulate with gloves on.
Black Diamonds best-selling and most trusted camming device, the Camalots' double-axle design offers a much larger range for each cam unit compared to traditional single-axle units. Because loading forces are shared between both axles, this design has the strength to work as a full-strength cam stop, allowing the cam to function as passive pro if it walks back into a wider part of a crack and umbrellas. In addition, they feature an C-Loop continuous cable stem design that is strong and durable, and they are colour-coded for easy identification. Finally, the triggers and cable loops are easy to grab, and the slings are large enough to manipulate with gloves on.
Black Diamonds best-selling and most trusted camming device, the Camalots' double-axle design offers a much larger range for each cam unit compared to traditional single-axle units. Because loading forces are shared between both axles, this design has the strength to work as a full-strength cam stop, allowing the cam to function as passive pro if it walks back into a wider part of a crack and umbrellas. In addition, they feature an C-Loop continuous cable stem design that is strong and durable, and they are colour-coded for easy identification. Finally, the triggers and cable loops are easy to grab, and the slings are large enough to manipulate with gloves on.
The Black Diamond Hoodwire Quickpack had 6 12cm quickdraws. Each is lightweight, easy-clipping setup with a non-snagging wiregate. Features Weight: 59.2g Size (Length): 12cm Size (Width(: 10cm Lightweight, easy-clipping setup with a non-snagging wiregate
Classic pitons for thinner cracks, Knifeblades have precision-ground blades for a consistent taper and a hole in the thickest part of the head to reduce weight without sacrificing durability. Features 2 clip-ins for corner placements and weight reduction
The Black Diamond ATC is a versatile belay that guarantees secure and smooth transit in the vertical world. The high friction mode offers three times greater hold and stopping power for 7.7 to 11mm ropes, while the geometric, fluid design reduces rope kinking. The reliable 7075-T6 aluminium alloy makes for a lightweight, dependable, single-rope version of the ATC-XP, designed for sport cragging.Assorted colours.
The Metolius Bailout Crash Pad has a unique angled-hinge design that eliminates dead spots on the fold line. The tri-layer foam fill gives great impact absorption and will retain its shape landing after landing. The pad's closure comes with alloy buckles so tough they come with a lifetime guarantee. Features Weight: 4kg Dimension (open): 91 x 122 x 10cm Fill Material - Top: 25 mm closed-cell foam Fill Material - Middle: 60 mm open-cell foam Fill Material - Bottom: 15 mm closed-cell foam
The Dragon Cam is a patented twin axle, single stem camming device that is the perfect mainstream cam for traditional climbing.Hot forged cams that combine lightness with strengthTwin axle design for extended expansion range and smooth action.Constant 13.75 camming angle.Extendable 8mm dyneema sling.Strong springs help create a stable placement that resists walking.The stem system uses. Moulded ergonomic trigger bar.Replaceable trigger wire system.Colour coded for easy size recognition.Anodised cams for corrosion prevention.**Please note that these cams are sold separately.
The Petzl Reverso Belay Device is a multi-purpose, lightweight and easy to use belay/rappel device. It features asymmetrical V-shaped grooved friction channels that adapt the friction on the rope according to its diameter and condition (ARC -Adaptive Rope Control- technology).Ultra-light designA single device for all rope typesclimbers and can be used for rappellingV-shaped friction channelsAsymmetrically grooved sidewallsCarabiner hole to release device when loaded? in Reverso mode: allows the loaded device in Reverso mode to be easily and gradually released with only a carabinerRope friendly, facilitates belay and rope handlingIntuitive useUse with symmetrical shaped locking carabiners (Am'D or OK) to maximize efficiency no matter which end is closest to the device.
The Wild Country VC Pro II's design is based on the principles so effectively demonstrated by the success of the original VC, that any all-around device needs to do the three essentials well: paying out quickly, holding falls securely and abseiling safely.The VC Pro takes this one step further by doing this brilliantly across a wider more modern range of rope sizes. The VC Pro 2 will deal with single Ropes from 9mm upwards and double ropes from 7.7mm upwards.
The Wild Country Helium Friend is one of the strongest and lightest ever built. One of the most inspired, innovative and copied products in climbing, it has been superbly re-engineered so that it continues to be the ultimate Friend. Features Hot forged cams New trigger New Thumb loop New 12mm Dyn sling Trigger stop New springs New stainless axle All units 12kN New stem cover More reach Up to 6% lighter per unit Up to 20% more range per unit Bigger overlaps 13.75 cam angle Single axle Single stem Scaled head width Full floating trigger with independent cam triggering Full strength cam stops Colour coded Silver: 1.5 Gold: 2.5 Purple: 3.0
The compact MINI TRAXION has three distinct modes of operation (pulley, progress capture pulley, ascender), making it the ideal companion for extended vertical adventures. Use it for hauling light loads, self-belay, ascending rope and self-rescue.Efficient and compact: aluminum sheave mounted on a self-lubricating bearing Trigger cam with teeth and cleaning slot works even on dirty or icy ropesCam can be locked in open position so device can be used as a simple pulleyCan also be used to ascend a ropeFor use on ropes between 8 and 13 mm in diameter.
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 4: Colour: Gold. Strength: 12kn. Weight: 30gSize 5: Colour: Blue. Strength: 12kn. Weight: 32gSize 6: Colour: Red. Strength: 12kn. Weight: 36gThese rocks are sold separately
Designed for Alpine climbing. The Onda pitons are designed to fit a wide variety of crack widths, made of nickel chromolly steel for the ultimate in durability. To alleviate the problem of sharp edges damaging alloy carabiners the stamped eye is reinforced with a stainless steel grommet which prevents the piton from cutting into the carabiner in the event of a fall.
This very lightweight pulley with a nylon wheel is designed for rescue, sack hauling etc. and for occasional use in mountaineering and caving.The swing cheek pulley is not designed for use on Tyrolean traverses or for organised rescues.Maximum rope diameter = 13mm.Weight:--- 55gr.
This multi-purpose Reverso 4 belay device is ultra-light (59g) and intuitive to use. V-shaped friction channels with asymmetrical lateral grooves adapt the friction to the type of rope for better control (ARC technology: braking control for twin, half and single dynamic ropes). Reverso mode for belaying one or two seconds with assisted braking. Features Ultra-light design Minimalist construction Hot-forged aluminum Weight: 59 g A single device for all rope types Can belay the leader, one or two seconding climbers and can be used for rappelling Independent and simultaneous belaying of one or two seconding climbers in Reverso mode Quick changeovers from Reverso mode to belaying the leader when climbing multi-pitch routes V-shaped friction channels Asymmetrically grooved sidewalls Carabiner hole allows the loaded device in Reverso mode to be easily and gradually released with only a carabiner Rope friendly, allows for smooth belaying and rope handling
Rockcentrics are easy to select, easy to place, and their place amongst the best selling kit of all time is testament to their enduring usefulness.Features:- Anodised colour coded heads and slings- 12mm dymeema co-ordinated tape- 6082 T6 alloy, 3 Sigma rated, CE EN12270Size 3: Colour: Gold. Strength: 14kn. Weight: 34gSize 4: Colour: Silver. Strength: 14kn. Weight: 43gThese rockscentrics are sold separately
The Black Diamond ATC Guide is a superbly versatile belay/rappel device thanks to its smooth and grooved sides, and the "guide mode" that allows you to bring up one or two seconding climbers with ease and control.Multiple friction modes for belay and rappelGuide mode works with one or two climbers ascending and descendingDependable and smooth operation in all conditions handling ropes from 7.7 to 11 mmAssorted colours
The Wild Country Rockcentric is highly versatile, one nut can provide four placement modes. Two of these modes are 'camming style placements', making them an effective starter tool for those who can't afford or aren't confident using cams. Features Curved sides, which make more points of contact than flat sided nuts. Anodised and with colour coded dyneema to match. Ease of placement and removal. Light weight compared to the original Hex.
The Petzl Standard Basic ascender is a lightweight, compact multi-purpose ascender that is great for use as part of a hauling system, or when ascending fixed lines. Designed for use on single ropes 8-13mm, it has a chrome-plated steel cam with angled teeth and a self-cleaning slot that grips ropes even in muddy or icy conditions, as well as multiple attachment points.
Meant for emergency use, this is the smallest and lightest rope clamp type ascender on the market. It will get you out of many difficult situations by helping you to set up a quick hauling system, or climbing a rope. Very useful for self rescue from crevasses etc. Every climber should have at least one Tibloc in their kit.For use on ropes of 8 - 11mm diameter.Weight:-- 39gr.
Rockcentrics are easy to select, easy to place, and their place amongst the best selling kit of all time is testament to their enduring usefulness.Features:- Anodised colour coded heads and slings- 12mm dymeema co-ordinated tape- 6082 T6 alloy, 3 Sigma rated, CE EN12270Size 8: Colour: Blue. Strength: 14kn. Weight: 118gSize 9: Colour: Violet. Strength: 14kn. Weight: 156gThese rockcentrics are sold separately
The Petzl Verso is a simplified version of the Reverso offering a lighter and more compact option for climbers looking to further reduce the weight/size of their rack of gear. The asymmetrical V-shaped grooved friction channels adapt the friction for better control using Petzl's ARC (Adaptive Rope Control) technology.
This via ferrata lanyard has all the features you'll need for a great day out on the cliffs. The retractable lanyard arms help keep them out of the way. Stored in a zippered pouch, the tearing energy absorber is protected and is easy to inspect. The third arm is great when traversing or when you need to rest by clipping directly to a rung.SCORPIO VERTIGO WL (504 g)
The Fixed Sided Pulley is lightweight, compact, and quick to install on the rope. It offers a good balance between weight and strength.* Allows a hauling system to be set up when used with a mechanical ascender* Also useful for redirection of the rope to avoid rope drag and wear* High efficiency due to the sheave mounted on self-lubricating bushings
Black Diamond Angles fit larger cracks, pockets and pods, and their design, coupled with the springiness of the steel used, gives these pitons inherently high holding power. Features Passive spring design for holding power Easy clip-in point
Rockcentrics are easy to select, easy to place, and their place amongst the best selling kit of all time is testament to their enduring usefulness.Features:- Anodised colour coded heads and slings- 12mm dymeema co-ordinated tape- 6082 T6 alloy, 3 Sigma rated, CE EN12270Size 5: Colour: Green. Strength: 14kn. Weight: 54gSize 6: Colour: Red. Strength: 14kn. Weight: 69gSize 7: Colour: Gold. Strength: 14kn. Weight: 91gThese rockcentrics are sold separately
The Petzl GripPro is a great finger and hand exerciser, allows individual finger strengthening. Designed to maintain the health and performance of fingers and hands for rock climbing training. Features Most advanced hand exerciser Ideal for those seeking maximum performance
The Petzl Universo is belay system combining a Verso and an Attache 3D held in optimal position by a sliding connection piece. The Universo is a complete and lightweight belay system that is particularly comfortable and efficient to use on all rope diameters. Features Exclusive connection piece allows the VERSO belay device to remain in position and the ATTACHE 3D carabiner to work along its major axis Connection piece also limits the risk of dropping the belay device during rope maneuvers Easy and quick installation on the rope Reduced risk of being burnt by the belay device when removing it from the rope System is easily reversed (right/left) A single device for all rope types Asymmetrically grooved sidewalls Rope friendly, allows for smooth belaying and rope handling Weight: 120g
The Verso is Petzl's lightest belay device with adaptive rope control technology. The asymmetrical V-shaped grooved friction channels adapt the friction for better control using our ARC (Adaptive Rope Control) technology. Features Ultra-light design Hot-forged aluminum Weight: 57g Single device for all ropes ARC technology adapts to the diameter of the rope used by increasing or decreasing the braking friction on the rope according to its diameter and condition Increased friction on thinner ropes Adapted friction for efficiency with larger diameter ropes Asymmetrical grooved sidewalls decrease friction when taking in slack for greater ease of use Super compact design is easy to use and doesn't take up much space on your rack Rope friendly design separates the two strands of rope when belaying with half/twin ropes or while rappelling, thus helping to prevents kinks Stiff keeper cable will not get sucked into the device and keeps it in the optimal position while
Metolius were the first company in North America to begin making climbing holds and training boards. They make training devices out of wood because it's strong, lightweight, pleasing to the eye and a renewable resource. It's also the perfect material for training as it provides enough texture for excellent grip with minimal impact on the skin.Features:This is the compact version of the popular Wood Grips Deluxe Training BoardLarge assortment of holds including jugs, big sloper, edges and pocketsIncludes comprehensive instructions and training guideIncludes mounting hardware24.5"x 5.125" (622 mm x 130 mm)
The Wild Country VC Pro 2 has a simple organic shape and ease of use that make this a modern belay device that is truly confidence inspiring. Built to have a perfect combination of abilities the VC Pro 2 has plenty of bite on thin cords yet a smooth payout on fatter ropes. So from midweek on an indoor wall, to sports climbing, double rope traditional or Alpine heres a device thats effective and gives total confidence in one neat package. Sitting beautifully in the hand the VC Pro 2 is easy, forgiving and obvious to use, even for beginners. Experts will also admire its adaptability because like the original VC it can be used in two modes, either slick or with more bite depending on circumstance and ropes chosen. So as the lightest of its type on the market, fitting a wide range of ropes, with a simple shape, a large keeper loop and a stylish range of colours the VC Pro 2 should be your next best friend and remain by your side for years to come. Set available with Synergy Lite Keylock HMS. Features Weight: 80g The VC Pro 2 will deal with single Ropes from 9mm upwards and double ropes from 7.7mm upwards
New and Improved DesignInnovative, portable training deviceTwo independent units, each with flexible, single point suspension; allows rotation of joints for injury preventionThe master is CNC milled for perfect symmetryFine textureLarge jug on top; deep, incut 4-finger pocket; 4-finger flat edge, 3-finger pocketIncludes comprehensive instructions and training guide7.25" x 5.75"x 2.25"(184 mm x 146 mm x 57 mm)Set of two: (1.9 kg) Sold in sets of twoColour: assorted
Metolius were the first company in North America to begin making climbing holds and training boards. They make training devices out of wood because it's strong, lightweight, pleasing to the eye and a renewable resource. It's also the perfect material for training as it provides enough texture for excellent grip with minimal impact on the skin.Features:Super skin-friendly wood training boardLarge assortment of holds including jugs, big sloper, edges and pocketsIncludes comprehensive instructions and training guideIncludes mounting hardware28.25"x 6.9" (718 mm x 175 mm)
These nuts come in four sizes that cover a very large size range, and work well in standard placements but also have an extremely efficient camming system. The double dyneema* sling is protected on the top by a large countersunk groove, which also makes racking them much easier. In addition, they are anodised for recognition and corrosion protection.Size 1: Colour: Green. Strength: 14kn. Weight: 54gSize 2: Colour: Red. Strength: 14kn. Weight: 70gSize 3: Colour: Gold. Strength: 14kn. Weight: 104gSize 4: Colour: Blue. Strength: 14kn. Weight: 146gThese torque nuts are sold separately
The Rock on wire is the original curved nut from Wild Country. These are the larger rocks in the range.Recent improvements to the rock on wire include a neat five degree side cut which gives new and more solid end-on' placement possibilities. This extends the range of placements and therefore the versatility of every nut.As usual with Wild Country protection these rocks have anodised colour coding. This makes the rocks easy to distinguish and faster to select. Each colour co-ordinates with the equivalent Friend and Zero size, as well as other colour coded Wild Country products.The side wall on each of these nuts is now thinner, optimising their strength to weight ratios.Size 1: Colour: Violet. Strength: 7kn. Weight: 16gSize 2: Colour: Green. Strength: 12kn. Weight: 25gSize 3: Colour: Silver. Strength: 12kn. Weight: 28gSize 4: Colour: Gold. Strength: 12kn. Weight: 30gSize 5: Colour: Blue. Strength: 12kn. Weight: 32gSize 6: Colour: Red. Strength: 12kn. Weight: 36gSize 7: Colour: Gunmetal. Strength: 12kn. Weight: 36gSize 8: Colour: Turquoise. Strength: 12kn. Weight: 41gThese rocks are sold as a set
The Rock on wire is the original curved nut from Wild Country. These are the larger rocks in the range.Recent improvements to the rock on wire include a neat five degree side cut which gives new and more solid end-on' placement possibilities. This extends the range of placements and therefore the versatility of every nut.As usual with Wild Country protection these rocks have anodised colour coding. This makes the rocks easy to distinguish and faster to select. Each colour co-ordinates with the equivalent Friend and Zero size, as well as other colour coded Wild Country products.The side wall on each of these nuts is now thinner, optimising their strength to weight ratios.Size 9: Colour: Gold. Strength: 12kn. Weight: 49gSize 10: Colour: Silver. Strength: 12kn. Weight: 60gSize 11: Colour: Green. Strength: 12kn. Weight: 70gSize 12: Colour: Red. Strength: 12kn. Weight: 81gSize 13: Colour: Gold. Strength: 12kn. Weight: 94gSize 14: Colour: Blue. Strength: 12kn. Weight: 109gThese rocks are sold as a set
Metolius has 25 years of experience in making climbing holds. They have put a lot of thought, time and effort into making quality holds that are fun to climb on and at the same time pleasing to the eye with a large variety of colors and unique features. Finally, there's a How-to-build a Climbing Wall guide included.Features:Incredible value!Each Mega Pack contains a random mix of various sizes of holdsMakes the ideal starter set for a home wallIncludes all hardwareWhat's Included:40 Holds6 Screw-On Footholds6 Screw-On Handholds1 Screw-On Rail1 Screw-On Plate1 Screw-On Outside Corner5 Screw-On Modulars8 Micros7 Modulars4 Mini Jugs1 Macro/Roof JugMulti-WrenchHow to Build a Home Bouldering Wall booklet
These brilliantly versatile Wild Country nuts utilise two existing technologies: the extrusion from the bestselling Rock with the soldered sleeve from the Zeros, to create a light hybrid unit. Designed to complement any rack by combining extreme light weight with a wide range of placements; their reduced width means they will fit in places where current wider nuts wont and grab shallow placements and pinscars brilliantly. One important thing not to be overlooked is that front to back these Superlights are exactly the same shape as standard Rocks and so in extremis are a direct, but very light replacement, and can be carried as such - or they make a second set. So for big wallers / alpinists / speed freaks and those pushing the trad limits the potential is enormous. So although at first glance Superlights may look very specialist or a little peripheral, Superlight Rocks can be seen as an essential 'addition' to a rack the kit bridging the gap between ones rack of 'tinies' and standard wires. Features 7075 alloy for easier removal Single wire Colour coded anodising Tapered sides 7075 T6 alloy 3 Sigma rated
The Wild Country Helium Friend is one of the strongest and lightest ever built. One of the most inspired, innovative and copied products in climbing, it has been superbly re-engineered so that it continues to be the ultimate Friend. Features Hot forged cams New trigger New Thumb loop New 12mm Dyn sling Trigger stop New springs New stainless axle All units 12kN New stem cover More reach Up to 6% lighter per unit Up to 20% more range per unit Bigger overlaps 13.75 cam angle Single axle Single stem Scaled head width Full floating trigger with independent cam triggering Full strength cam stops Colour coded Blue: 3.5 Silver: 4.0
In order to provide more racking options in DMM's active protection range they combined some of the favourite features from our two existing cams: the tried and trusted 13.75, single axle head unit of the 4CU, with the justifiably popular stem assembly of the Dragon with its patented thumb press and extendable sling design. The result is a lightweight, versatile, and functional device that caters for climbers who prefer single stem ergonomics, for those who are used to our traditional sizing system, and for those who want to double up their cam racks to offer even more placement options. The range covers placements from 13mm to 100mm in nine colour coded sizes. The colours follow the same sequence as the 4CU, but they have reversed the cam lobe colouring to the opposite to the Dragon for easily identification. Features A lightweight single axle, single stem cam Special thumb grip and trigger bar for easy handling Original 13.75 camming angle Cam stops for 10kN in passive position Fitted with extendable 8mm Dyneema slings Colour coded to help you make a speedy identification Gold: Demon Cam 1 Red: Demon Cam 2 Purple: Demon Cam 3
DMM updated the conventional design by dropping the wire into a recess with a full radius to keep it protected and give extra strength, creating the DMM HB Alloy Offset. They also reduced the weight with lightening holes on the two larger sizes. On slightly flared placements nothing fits like an Offset. Get a set as a back up for your Wallnuts and prepare to be converted. Features Offset alloy nuts on wire Wire recessed into top of nut and full wire radius for extra strength Lightening holes Colour coded for easy recognition
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 10: Colour: Silver. Strength: 12kn. Weight: 60gSize 11: Colour: Green. Strength: 12kn. Weight: 70gThese rocks are sold separately
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 12: Colour: Red. Strength: 12kn. Weight: 81gSize 13: Colour: Gold. Strength: 12kn. Weight: 94gThese rocks are sold separately
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 14: Colour: Blue. Strength: 12kn. Weight: 109g
The Wild Country Helium Friend is one of the strongest and lightest ever built. One of the most inspired, innovative and copied products in climbing, it has been superbly re-engineered so that it continues to be the ultimate Friend. Features Hot forged cams New trigger New Thumb loop New 12mm Dyn sling Trigger stop New springs New stainless axle All units 12kN New stem cover More reach Up to 6% lighter per unit Up to 20% more range per unit Bigger overlaps 13.75 cam angle Single axle Single stem Scaled head width Full floating trigger with independent cam triggering Full strength cam stops Colour coded Red: 0.5 Gold: 1
The Black Diamond ATC-XP is a durable, versatile belay device that features multiple friction modes to handle nearly any situation or rope diameter. Features 30% lighter than the original High-friction mode offers 3 times greater hold and stopping power than regular-friction mode Machined windows through device for weight savings Durable cable holds its shape and resists getting caught up between ropes Hot-forged construction Versatile design accepts ropes from 7.7 to 11 mm
The Petzl Basic is a compact ascender that offers excellent grip for rope ascents. The lower attachment hole is large enough to hold the carabiners for the lanyard and the footloop. Features Compact ascender with excellent grip Can be used for rope ascent on a fixed line or as progress capture in a hauling system Toothed cam with self-cleaning slot optimizes performance under any conditions (e.g. frozen or dirty ropes) Stainless steel cam has better resistance to corrosion Lower attachment hole large enough for two carabiners (lanyard and foot loop) Upper connection hole for guiding the rope Material(s): aluminum for the frame, stainless steel for the cam, nylon for the trigger Weight: 90g Rope: for use with single ropes between 8 and 11 mm
The Petzl left or right-handed ascenders are designed for use with single ropes 8 to 13mm. Its chrome-plated steel cam has angled teeth and a self-cleaning slot that securely grips the rope even in muddy/icy conditions, while the ergonomic thumb-catch allows one-handed installation and removal. In addition, it has a safety catch that prevents the cam opening too far, a comfortable moulded grip and multiple attachment points.
The Petzl left or right-handed ascenders are designed for use with single ropes 8 to 13mm. Its chrome-plated steel cam has angled teeth and a self-cleaning slot that securely grips the rope even in muddy/icy conditions, while the ergonomic thumb-catch allows one-handed installation and removal. In addition, it has a safety catch that prevents the cam opening too far, a comfortable moulded grip and multiple attachment points.
The Petzl Micro Traxion is an ultra-light, ultra-compact progress capture pulley that is exceptionally efficient. The cam can be locked in open position so the device can be used as a simple pulley. Works even on frozen or muddy ropes. Features Pulley with integrated progress capture device can be used as a progress capture pulley or simple pulley Upper button allows cam to be locked in open position Aluminum sheave mounted on sealed ball bearings for excellent efficiency Rope clamp works on muddy or frozen ropes Ultra-compact and lightweight Weight: 85g Min. rope diameter: 8mm Max. rope diameter: 11mm Material(s): aluminum, steel, stainless steel, nylon
The Cardiac Arrester allows the user to choose two orientations to vary the amount of friction that can be applied to the rope, allowing you to choose the speed of descent.Features:Hot forged, heat treated and rumbled until they are super smooth.Anodised for protection against coastal and rigorous mountain environments.**These come in a variety of colours including blue, green, orange and red. We cannot guarantee what colour will be provided.**
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 1: Colour: Violet. Strength: 7kn. Weight: 16gSize 2: Colour: Green. Strength: 12kn. Weight: 25gSize 3: Colour: Silver. Strength: 12kn. Weight: 28gThese rocks are sold separately
Features:- Combines aluminium alloy and stainless steel for strength and performance- Each nuts width is slightly larger than its thickness for faster selection and a broader range of placements- Anodised with a colour-coded swage for quick identificationSize 7: Colour: Gunmetal. Strength: 12kn. Weight: 36gSize 8: Colour: Turquoise. Strength: 12kn. Weight: 41gSize 9: Colour: Gold. Strength: 12kn. Weight: 49gThese rocks are sold separately
These nuts come in four sizes that cover a very large size range, and work well in standard placements but also have an extremely efficient camming system. The double dyneema* sling is protected on the top by a large countersunk groove, which also makes racking them much easier. In addition, they are anodised for recognition and corrosion protection.Size 1: Colour: Green. Strength: 14kn. Weight: 54gSize 2: Colour: Red. Strength: 14kn. Weight: 70gSize 3: Colour: Gold. Strength: 14kn. Weight: 104gSize 4: Colour: Blue. Strength: 14kn. Weight: 146gThese torque nuts are sold as a set
Training boards are absolutely brilliant for building contact strength necessary for climbing - whether you're just learning and developing new found muscles or are the full-on power junkie looking for extra reserves. Time spent on a training board will directly correlate to success at the crag. Features:The master is CNC milled for perfect symmetryThe holds are arranged along a broad arc that tapers outward and downward forbetter ergonomics and reduced injuriesTapers from top to bottom in both dimensions for better forearm clearanceFine textureMassive variety of holdsIncludes comprehensive instructions, training guide and all mounting hardware28" x 8.75" (711 mm x 222 mm)Colors: May Vary
The Metolius Portable Power Grips are super compact, lightweight and great for travel - can be stowed and set up nearly anywhere! Features Small custom curved wooden blocks Hang like Rock Rings Sold in pairs Four hold combination allows for a variety of pull-up related training exercises Body weight only 127 m x82.5m 63.5 mm 481g