Sanding deep & wide work pieces, front edges, narrow inner curves, horizontal, vertical, diagonal, with or across the grain; it’s all part of a day’s work with the scheppach bsm 2010 belt sanding machine & the job is completed in no time to your total satisfaction. In vertical sanding mode the 198 mm wide anodised aluminium tables offer more than adequate support & the smoothest surface to work off. The continuous table height adjustment enables you to use the full width of the belt equally which becomes cost effective & economical in use the most generous sanding surface allows the safe & proficient sanding of larger work pieces & the belt speed of 11 m/sec eliminates the possibility of overheating & discoloration of the wood. Efficient corner sanding. Both tables are adjustable from 0 to 45 degrees using small rotating rollers allowing perfect diagonal sanding even on tight inner curves. The standard safety fence means that you can work with small work pieces safely. A handle provides quick & easy adjustment of the bsm 2010 to either horizontal or vertical sanding modes. An optional sturdy floor stand makes it possible to convert the machine from a bench top unit to a floor standing machine. Due to the connecting piece for a scheppach extractor unit, the bsm 2010 got the test certificate "wood dust tested". Standard equipment: folding sanding plate with workpiece fence, height adjustor, swivel length table, swivel cross table, 3 sanding belts, suction connector, assembly tool.. ...

The perfect finishing touch with the bsm 2010 belt sander. Sanding deep & wide work pieces, front edges, narrow inner curves, horizontal, vertical, diagonal, with or across the grain; it’s all part of a day’s work with the scheppach bsm 2010 belt sanding machine & the job is completed in no time to your total satisfaction. In vertical sanding mode the 198 mm wide anodised aluminium tables offer more than adequate support & the smoothest surface to work off. The continuous table height adjustment enables you to use the full width of the belt equally which becomes cost effective & economical in use. The most generous sanding surface allows the safe & proficient sanding of larger work pieces & the belt speed of 11 m/sec eliminates the possibility of overheating & discoloration of the wood. Efficient corner sanding. Both tables are adjustable from 0 to 45 degrees using small rotating rollers allowing perfect diagonal sanding even on tight inner curves. The standard safety fence means that you can work with small work pieces safely. A handle provides quick & easy adjustment of the bsm 2010 to either horizontal or vertical sanding modes. The sturdy floor stand makes it possible to convert the machine from a bench top unit to a floor standing machine. The continuous table height adjustment allows evenly sanded surfaces & corners. Standard equipment
Includes:: folding sanding plate with workpiece fence, height adjustor, swivel length table, swivel cross table, 3 sanding belts, suction connector, assembly tool. dimensions: l 1250 x w 520 x h 420mm. Grinding plate: 800mm. Length table

Size: 770mm x 200mm. Cross table

Size: 480mm x 200mm. Sanding beltlength/
Width: 2000/150mm. Belt speed: 11m/sec. Motor input: 2.7 kw (3.7 hp). Output: 2.0 kw (2.7 hp). Speed: 2.0 kw (2.7 hp).





...

Scheppach bts 900 belt & disc sander. economic belt & disc sanding – the bts 900 bench top sander belt & disc sanding are combined with the bts 900 sander. This is the major benefit with the bts 900. Belt & disc sanding in one compact unit that can be easily stored when not in use. The belt sanding option can be adjusted vertically through 90 degrees & the sanding table can be mounted for both belt & disc sanding operations. The sanding belt can be continuously adjusted from horizontal to vertical. The cast-iron base keeps the sander stable during use, so you can apply the desired amounts of pressure & achieve consistent results. the tilting table can be positioned for both belt & disc sanding operations. Both belt & disc sanding are provided with the bts 900x. the belt sander unit can be adjusted by 90° from vertical to horizontal position. the sanding table, swinging through 45°, can variably be used for belt & disc sanding. at the cross stop, any angle can be exactly set. technical data:

Dimensions (l / w / h ): 530 x 410 x 290mm. grinding plate: 290mm. table

Size: 159mm x 225mm. table adjustment: 45°. sanding belt length/
Width: 915mm/100mm. sanding belt grit

Size: 80. belt speed: 7.5rpm. sanding disc speed: 2350rpm. suction connector ø: 32mm. weight approx: 25kgs. image 2: the sanding belt can be continuously adjusted from horizontal to vertical. image 3: the tilting table can be positioned for both belt & disc sanding operations. image 4: the sanding discs are easily attached with the velcro fastening system.






...

With a new scheppach deco-flex hobby scroll saw, new standards for model & hobby craft are achieved. You still have the same quality of manufacture & precision for intricate cuts in wood, metal & plastics with the added feature of a flexifrive system to insert additional cutting, grinding & polishing tools all powered from the one unit. This truly is a perfect universal hobby craft tool for the home, education & professional workshops.
Features: no load speed: 400-1600rpm. cutting length: 405mm. cutting

Height: 50mm. sawblade length: 133mm. table tilt: 0
- 45°. size l x h x d: weight 15kg.



...

Scheppach dms 1100 heavy duty lathe with unique clockwise & anti-clockwise rotation. Powered by a very quiet running, high torque 1 hp induction motor, it gives ten speeds ranging from 500 rpm 2, 100 rpm & is therefore ideal for small diameter spindle work through to large bowl turning. Speed selection is made by a conveniently placed lever. Both the headstock, tailstock & lathe bed are made from solid cast iron which has been accurately machined to allow for smooth movement & minimal levels of vibration. The pivoting headstock turns 360° & locks to facilitate outboard turning. Fitted with the industry standard 1“ x 8 tpi main spindle, there will never be a need to worry about sourcing a wide range of accessories. standard equipment. stable, torsion resistant grey cast iron construction, plane, polished turning bed, cast iron spindle stock, tailstock & tool rest, toolrest & tailstock with eccentric clamp, slewable spindle stock, face plate, drive centre 4-point, following centre point, adaptor for m 33, 10 spindle speeds, poly v belt drive, wise & anticlockwise rotation. technical data:

Dimensions (l/w/h): 1, 610mm x 490mm x 1, 175mm.bed

Height: 910mm. spindle head thread: 1" x 8 tpi.spindle head cone: mk 2.tailstock cone: mk 2.tailstock bore (hollow spindle): 9mm.distance between centres: 1050mm.height of centers over bed °: 175°.sleeve adjustment: 55mm. spindle speeds: 500/600/750/900/1, 000/ 1, 200/1, 400/1, 600/1, 800/ 2, 100rpm.turning ø over bed: 355mm.tool rest length: 300mm.face plate ø: 150mm.weight approx. 92kgs. Motor: 230–240 v/50 hz. input: 0.75kw (1.0hp). output: 0.5kw (0.68hp). speed: 1, 400rpm.



...

The scheppach dms 900 woodturning lathe is designed with the committed artisan in mind as well as the professional who requires a machine with an excellent

Specification at a competitive price. Built of cast iron the dms series lathes are made to last. Powered by a very quiet running, high torque 0, 75 hp induction motor, it gives ten speeds ranging from 500 rpm 2, 100 rpm & is therefore ideal for small diameter spindle work through to large bowl turning. Speed selection is made by a conveniently placed lever. Both the headstock, tailstock & lathe bed are made from solid cast iron which has been accurately machined to allow for smooth movement & minimal levels of vibration. The pivoting headstock turns 360° & locks to facilitate outboard turning. Unique to the scheppach dms series is the clockwise & anticlockwise spindle rotation which offers the advantage of positioning the tool rest to the left or right when swivelling the headstock. The l & r turning facility also produces perfect sanding results on the finished workpiece irrespective of the lay of the wood grain. The tailstock is bored to allow for long hole boring when making table & standard lamps. Fitted with the industry standard 1" x 8 tpi main spindle, there will never be a need to worry about sourcing a wide range of accessories. Standard equipment
Includes:: stable, torsion resistant grey cast iron construction, plane, polished turning bed, cast iron spindle stock, tailstock & tool rest, toolrest & tailstock with eccentric clamp, slewable spindle stock, face plate, drive centre 4-point, following centre point, adaptor for m 33, 10 spindle speeds, poly v belt drive, wise & anticlockwise rotation.

Dimensions (l/w/h): 1, 510mm x 490/1mm x 120mm. Bed

Height: 890mm. Tailstock bore (hollow spindle): 9mm. Distance between centres: 825mm. Height of centers over bed ° sleeve: 152mm. Spindle speeds: 500/600/750/900/1, 000/ 1, 200/1, 400/1, 600/1, 800/ 2, 100rpm. Turning dia over bed: 304mm. Tool rest length: 300mm. Face plate diameter: 150mm. Weight: 80kgs approx.






...

The scheppach dmt 450 is ideal for the hobby woodturner who does not have sufficient dedicated workbench space for his lathe, being small enough to “side“ when not in use. It is also most useful for woodturners who are on the move as it is small enough to transport in the boot of a car. The powerful 1/2hp induction motor has high torque capacity to allow for turning of heavy timbers without stalling. The precision machined main drive spindle runs on two industrially rated sealed-for-life bearings to maximize support & has a 1" by 8 tpi thread. The 5 step pulley system with poly-v belt drive offers a speed range between 650 & 3, 000 rpm: speed change being quick & simple. This new scheppach mini lathe has a heavy-duty cast iron bed that ensures stability & minimal vibration. Distinguished also by its

Specification, the dmt 450 gives 445 mm between centres & a turning diameter of 254 mm. The tailstock is hollow allowing up to 9 mm long hole boring. This is a well machined lathe that will bring years of turning satisfaction & find a home with many a discerning woodturner. Supplied with tool rest, face plate & revolving centre & a hollow tailstock for long hole boring as standard equipment. Standard equipment: stable, torsion resistant grey cast iron construction, plane, polished turning bed, cast iron spindle stock, tailstock & tool rest, toolrest & tailstock with eccentric clamp, face plate, following centre point, drive centre 4-point, adaptor for m 33, 5 spindle speeds, poly v belt drive.

Dimensions (l/w/h): 770mm x 285mm x 375mm. Bed

Height: 190mm. Spindle head thread: 1“ x 8 tpi. Spindle head cone: mk 2. Tailstock cone: mk 2. Tailstock bore (hollow spindle): 9mm. Distance between centres: 445mm. Tool rest length: 150mm. Face plate dia: 75mm.





...

This sanding machine is the ultimate in successful finishing of your woodworking projects. With special help from the sanding fence with comes with this tool even small pieces can be guided safely. In this unit is the integrated cabinet base where the dust extraction is cleverly concealed. This means you get great sanding finishes & a good enviroment to work in. ...