An essential part to be able to use the EDC Tool Kit on your bike, this top cap kit makes the toolkit easily accessible. It comes complete with a unique steerer plug that has a drain hole to prevent the build-up of any water of mud & also keeps the tool in place. This top cap kit would also be a worthwhile spare to consider, so you can easily swap the EDC toolkit between different bikes. Please Note: EDC Tool Kit sold separately. ...

These replacement “ Bacon Strip” repair plugs quickly seal any splits & punctures in tubeless tyres & get your bike rolling again as good as before. ...

Weighing just 38g, the High Direct Mount Chain Guide stops lateral chain movement to reduce wear on your chain, helping to eliminate the chance of untimely drops. Combatting chainring tooth wear at the same time, this Standard, Boost & Oval chainring-compatible lifesaver prolongs the life of your chain by double, making it an essential for the regular rider. ...

This stunning model is an answer to the growing trend for lower & slacker bikes by using simple, one tool installation & adjustment ...

This chainguide features a reinforced nylon bash guard & a backplate cut from 8mm thick 7075-T6 aluminium. This ensures that the One Up Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you may forget it’s even there. NOT JUST FOR ENDURO RACERS The One Up Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers & Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention. The One Up Bash Guide

Includes:: 3 different sizes of bash plate for compatibility with chainrings from 28-36T. GUIDE SETUP INSTRUCTIONS 1. Remove top guide by removing the front top guide nut with a 4mm hex (never adjust the rear T25 bolt). 2. Set slider in the highest position 3. Hold backplate directly against ISCG05 tabs. Check for clearance between the back side of the bashplate/guide & the bike frame (use included 2.5mm spacers if necessary to space the backplate away from the frame). 4. Rotate backplate until slider adjustment bolt is directly above the crank axle & torque bolts to 5 Nm 5. With crankset & chain installed, use spacer shim block to measure clearance between back plate & chain 6. Determine the corresponding number of chainline shims required 7. If more than 5 shims are required, install the supplied 2.5mm washers behind the backplate & return to step 2 8. Assemble top guide with spacers & tighten bolt to 3 Nm 9. Insert a 4mm hex through the hole in the inner top guide, loosen height adjustment bolt & lower the tool onto the chain. Torque to 3 Nm to set height BASH REPLACEMENT INSTRUCTIONS 1. Remove Bash Guide from bike 2. Remove bolt retaining clip from rear bash plate bolt by pushing a 4mm hex through the bolt from the backside of the guide. 2. Remove Bash bolts using a 5mm hex 3. Select desired bash plate & reinstall bash bolts to 6 Nm 4. Reinstall bolt retaining clip on the rear bash plate bolt 5. Reinstall Bash Guide onto bike

...

These oval chainrings provide the ultimate in traction by balancing out the torque delivered to your rear tyre by providing the same power delivery the entire way through your pedal stroke. Wide Ring Maximum Durability Featuring a wide tooth design provides maximum ring durability when running without a bash guard & aggressive crud chamfers give excellent mud shedding performance & extended ring life.

Features: Get ultimate traction by smoothing out the torque you deliver to your rear tyre 12% ovality (32T is equal to a 30T-34T range) 115° clocking from crank arm puts the major axis in your power stroke Narrow Wide tooth profile eliminates chain drop with the perfect chain mesh fit Perfect chainline with built in offset for a quieter drivetrain with enhanced chain wear & best drop performance Reuse your existing 8-10mm long ring hardware
- no new bolt packs required Aggressive crud chamfers for awesome mud shedding performance & extended ring life Reinforced wide tooth design provides maximum ring durability when running without a bash guard Made from hard wearing 7075-T6 aluminium plate 104-32T & 94-30T rings have integrated shims & chainring bolt threads to allow the smallest ring size possible.


...

Narrow Wide tooth profile eliminates chain drop with the perfect chain mesh fit Perfect 49mm chainline with 2mm Shims included for a quieter drivetrain, enhanced chainring wear & best no drop performance Reuse your existing 8-10mm long ring hardware
- no new bolt packs required Aggressive crud chamfers for awesome mud shedding performance & extended ring life Reinforced wide tooth design provides maximum ring durability when run without a bash guard 104-30T rings have integrated shims & chainring bolt threads to allow the smallest ring size possible.
...

One of the slight drawbacks to running a 1x 11 drivetrain is that you lose some top speed. However, with this expander sprocket on board, you can run a 34T chainring up front for extra speed on the flat, without losing the low gear range for the climbs. Smoother Gear Transitions In addition to the larger & easier climbing gear, One Up provide an 18T hardened steel sprocket, to help to smooth the progression between gears. This helps to ensure smaller jumps in resistance for efficient acceleration & smooth cadence when using the highest gears. Also, as the 40 or 42T sprocket is maintained, there’s a smooth transition to the expander & the cassette’s durability is maintained. ...

Switch a Chainring in Under a Minute One Up Components have designed the Switch Chainrings in conjunction with the Switch Chainring Carrier. This means the chainring can be used with any direct mount crankset standard when using the correct Switch carrier & it also makes it possible & hassle-free for the chainring to be changed in less than a minute without having to remove the crank from the bottom bracket. Easy Interchangeable Gear Ratio The Switch chainring interface enables the possibility of carrying a number of different chainring sizes with the intention to switch them depending on the terrain you will be tackling. For example, if you have a day planned, which consists mainly of climbing followed by a day of descending all the way back down, you can plan ahead & pick your chainring sizes for the trip based on the chainrings you would like to use. ...

This model features a hard-wearing aluminium construction, which makes it perfect at handling all the intensity that comes with blasting across the mountains at speed. Coming complete with internal cable routing & cable actuated remote compatibility, this MTB dropper is a perfect upgrade for fast & reliable saddle height adjustment on the move. Technologies: Easy to service at home Upper DU Bushing in the upper collar Increased bushing overlap & durability Travel Reducing Shim reduces travel by up to 20mm Weight: (30.9) 120mm 435g / 150mm 480g / 180mm 525g / 210mm 570g (31.6) 120mm 450g / 150mm 500g / 180mm 545g / 210mm 590g (34.9) 120mm 545g / 150mm 605g / 180mm 660g / 210mm 710g ...