Using two of the latest high-intensity LUMILEDS LEDs & incorporating both wide & narrow angle beams, the Blinder Road 250 floods any street in light, giving cyclists total night vision whilst being visible to others at over 1000m. ACCESSORIES INCLUDED: Helmet mount, 2x interchangeable straps for front light, USB (Universal Serial Bus) charge cable. LIGHT OUTPUT: 250 lumens DIMENSIONS: 53 x 30 x 63mm. WEIGHT:75g STORAGE MODE: To activate storage mode make sure light is first turned off. Then hold down the on/off button for 5 seconds & release when red LED comes on. This LED will stay lit until the light drops into storage mode. To reactivate light, plug into USB (Universal Serial Bus) port & charge as usual. Once charged light will turn on as before. CHARGING: When plugging the light into a USB (Universal Serial Bus) port to charge a red LED will display on the on/off switch of the light to indicate that the light is charging. When fully charged this light will turn green to indicate charging is complete. Compliance The Light Blinder Road 250 Front Light, from Knog, is fully compliant with German St VZO regulations ...

Delivering a colossal 250 lumen beam of light at the front & 70 lumens at the rear, they're the first Blinder lights of their kind to give riders 100% visibility & freedom at night, all from a super-compact, super-light, USB (Universal Serial Bus) rechargeable, waterproof, integrated silicone package. OUTPUT: Front
- 250 lumens // Rear
- 70 Lumens DIMENSIONS: Front
- 53 x 30 x 63mm // Rear
- 27x 76x 52. WEIGHT: Front
- 75g // Rear
- 52g LIGHT MODES: Front
- Total of 8 light modes: Narrow, High, Dual Beam & Flash in both High & Low // Rear
- 5 light modes: 1. Steady, 2. Fast, 3. Chaser, 4. Peleton, 5. Eco-Flash. RUN TIMES (FRONT): Narrow Beam; 1-2 hours, Wide Beam; 1-2 hours; Dual Beam; 2-3 hours, Flashing; 3-6 hours. RUN TIMES (REAR): 3.5 hours in Steady mode, 4 hours in Fast, 5 hours in Chaser, 13 hours in Peloton Mode & 20 hours in Eco-Flash. STORAGE MODE: To activate storage mode make sure light is first turned off. Then hold down the on/off button for 5 seconds & release when red LED comes on. This LED will stay lit until the light drops into storage mode. To reactivate light, plug into USB (Universal Serial Bus) port & charge as usual. Once charged light will turn on as before. CHARGING: When plugging the light into a USB (Universal Serial Bus) port to charge a red LED will display on the on/off switch of the light to indicate that the light is charging. When fully charged this light will turn green to indicate charging is complete.







...

With incredible power:weight ratio & dual + constant flash modes, you won’t find another light like this. ACCESSORIES INCLUDED: Helmet mount, 2x interchangeable straps for front light, USB (Universal Serial Bus) charge cable. LIGHT OUTPUT: 400 lumens DIMENSIONS: 53 x 30 x 75mm. WEIGHT:105g STORAGE MODE: To activate storage mode make sure light is first turned off. Then hold down the on/off button for 5 seconds & release when red LED comes on. This LED will stay lit until the light drops into storage mode. To reactivate light, plug into USB (Universal Serial Bus) port & charge as usual. Once charged light will turn on as before. CHARGING: When plugging the light into a USB (Universal Serial Bus) port to charge a red LED will display on the on/off switch of the light to indicate that the light is charging. When fully charged this light will turn green to indicate charging is complete. Compliance The Light Blinder Mob The Face Twinpack, from Knog, is fully compliant with German St VZO regulations. ...

Outputting 70 lumens of light, the Blinder ROAD R70 has got your back, whatever your ride. LIGHT OUTPUT: 70 lumens DIMENSIONS: 27 x 76 x 52mm. WEIGHT: 52g STORAGE MODE: To activate storage mode make sure light is first turned off. Then hold down the on/off button for 5 seconds & release when red LED comes on. This LED will stay lit until the light drops into storage mode. To reactivate light, plug into USB (Universal Serial Bus) port & charge as usual. Once charged light will turn on as before. CHARGING: When plugging the light into a USB (Universal Serial Bus) port to charge a red LED will display on the on/off switch of the light to indicate that the light is charging. When fully charged this light will turn green to indicate charging is complete. Compliance The Light Blinder Road R70 Rear Light, from Knog, is fully compliant with German St VZO regulations ...

Knog Light Blinder 1 Twinpack LED: Hi-tech gear, all that high-powered surface-mount LED & the lithium polymer with its inbuilt USB (Universal Serial Bus) recharge is held in sweetly by a flexible silicone strap & clip. & as a cruiser a tool-less attachment for handlebars & frames of 22-32mm. Visible at over 500 metres. DIMENSIONS: 25 x 25 x 33mm WEIGHT: 15g

Materials: UV-Resistant Industrial grade silicone. Polycarbonate Lens, Latch & Housing. Hard-anodised aluminium fascia. USB: Rechargeable Lithium Polymer battery FRONT: 20 lumens (LED Rating) REAR: 11 lumens (LED Rating) LEDs: Efficient LEDs designed to provide maximum brightness level for up to 90% of the battery burn time for each mode. Rather than LED brightness deteriorating during your ride. Lens: Use of an optic design to provide a balanced ratio of beam width & distance to safely illuminate you & the path ahead. Visibility: Light is visible at over 500 metres. Light Modes: 5 light modes: Steady, Fast Flash, Organic Flash Slow, Organic Flash Fast, Eco-flash. Burn Time: Burn time of over 2-hours in constant & up to 11-hours eco-flash mode. Battery: Rechargeable Lithium polymer battery via integrated USB (Universal Serial Bus) plug. Integrated USB (Universal Serial Bus) Plug: Designed to be exposed to the elements, the plug is also waterproof & will not be damaged by expsure. Button: New longer button push on (0.75sec) prevents accidental activation of your light. Short presses switch modes continuously. The light is switched off with a long button push off (0.5sec). Storage Mode: Storage mode provides the best longevity for your Blinder light. Repeat this procedure every 3 months thereafter if the light isnt being used.1. Charge the light for a full charge cycle. (indicator glows green when charged).2. Remove light from USB (Universal Serial Bus) charging device / port.3. Turn light on in any mode.4. Hold button down for more than 5 seconds, at which point the indicator LED will turn red.5. The light itself will remain on until the Blinder switches itself off & into storage mode. Bike Attachment: Tool-less attachment for handlebars/rear-posts & frames of 22-32mm &248; 100% Waterproof: The Blinder 1 is IP66 Tested & 100% waterproof against all elements. Testing: The Blinder 1 has been tested against the following; Drop tests, corrosion tests, UV tests, Electrical shock & static, vibration & impact, temperature & humidity, cycle testing & CE certification.

...

What do Knog mean by water resistant? If you are going to ride in the rain for more than 6 hours you should be just fine, but if you are taking the Knog Strobe deep sea diving then dont expect it to be all singing & dancing afterwards. Bottles, bars, stems, bags & helmets use your imagination the Knog strobe can attach to almost anything. Take it riding, running, camping, climbing & much more. ...

OUTPUT: FRONT 35 lumens // REAR 5 lumens DIMENSIONS: FRONT 25 x 25x 75 mm // REAR 25 x 25x 70 mm WEIGHT: 56g RUN TIME: FRONT 6.4 hrs (steady/low), 100 hrs (eco flash) // REAR 7 hrs (steady), 200 hrs (eco flash). GET STARTED 1/ Pop open the light with a coin. 2/ Take out the battery saver tab. Check your +/- when you slide the battery back in. 3/ Slide the unit back together firmly. 4/ Press & hold the on/off switch for about 1 second to turn light on. Press the on/off button quickly to scroll between light modes. LOW BATTERY INDICATOR: When the battery in the light is getting low a little red light will turn on (visible through the front lens) to indicate the battery in the light needs changing ...

Mounting The Light Pop I Light comes with a user friendly design that is ideal for the urban cyclists. One of the lights many convenient elements is that is comes with an integrated mounting system. The simple loop design provides a tool free attachment that can easily be taken on & off your bike’s handlebars. Low Battery Indicator The light is powered by an AA battery that comes included. When your battery life is running low the a little red light will appear through the front lens that can be seen when the main light is off. This lets you know that the battery needs replacing. Button The longer button push on (0.75 seconds) prevents the light accidentally turning on while transporting the light to & from your light. The light comes with various different modes including steady & flashing which can easily be changed with short presses on the button while the light is on. Side Visibility When cycling through built up urban areas you’ll often be faced with traffic coming at you from multiple different angles. Therefore it’s important to stay visible from all sides. The light therefore comes with a special beam that has been crafted to spread the visibility & the result is up to 180-degrees of visibility. ...

OUTPUT: 60 lumens DIMENSIONS: 75 x 38x 25 mm WEIGHT: 81g GET STARTED 1/ Pop open the light with a coin. 2/ Take out the battery saver tab. Check your +/- when you slide the battery back in. 3/ Slide the unit back together firmly. 4/ Press & hold the on/off switch for about 1 second to turn light on. Press the on/off button quickly to scroll between light modes. LOW BATTERY INDICATOR: When the battery in the light is getting low a little red light will turn on (visible through the front lens) to indicate the battery in the light needs changing ...

OUTPUT: 60 lumens DIMENSIONS: 75 x 38x 25 mm WEIGHT: 81g GET STARTED 1/ Pop open the light with a coin. 2/ Take out the battery saver tab. Check your +/- when you slide the battery back in. 3/ Slide the unit back together firmly. 4/ Press & hold the on/off switch for about 1 second to turn light on. Press the on/off button quickly to scroll between light modes. LOW BATTERY INDICATOR: When the battery in the light is getting low a little red light will turn on (visible through the front lens) to indicate the battery in the light needs changing ...