The Large Vortex Rainwater Collection Filters for Barns & Warehouses can be installed as part of a rainwater harvesting system where rain water from the roof is channelled through a horizontal underground pipe & is suitable for filtering large amounts of rainwater. The unit filters & diverts rainwater to a storage tank. Leaves, moss & other debris are washed through to the drain or soakaway. Rainwater enters the inlet connection in the side of the unit. The inlet is designed to swirl the water in a vortex like action around the surface of the stainless steel filter below. The rainwater is drawn through the vertical mesh walls of the fine filter by adhesion, then collected & fed through the outlet to the storage tank. Debris & particles that are too large for the filter are flushed through to the drain outlet by the action of water flowing down the surface of the filter. More than 95% of the rainwater entering the filter is filtered & collected by this principle. Pitched roofs of slate, clay or concrete are the most suitable for collecting rainwater. Flat roofs can also be utilised but the volume of water collected is reduced. Thatch or planted roof areas are less suitable due to the low collection efficiency & discolouration of the water that is collected. Technical

Specification Suitable for roof areas up to 200 square metres. Connects to standards storm water pipes below ground. Virtually all debris, moss, leaves, insects, etc. is washed through the uniquely constructed vertical filter by self-cleaning action. Unique oxygen-enriching function. No restriction or obstruction of water flow through the appliance. More than 95% efficient. Minimum maintenance. Tough polyethylene housing. High quality stainless steel filter mesh. 50cm extension tube can be trimmed to length to suit invert level. Can also be wall-mounted. Boxed

Dimensions & gross weights 100mm Filter
- 16kg 15 x 48 x 36 cm Wall Bracket
- 4kg 15 x 48 x 36 cm





...

The Large Vortex Rainwater Collection Filters for Barns & Warehouses can be installed as part of a rainwater harvesting system where rain water from the roof is channelled through a horizontal underground pipe.  It is suitable for filtering large amounts of rainwater. The unit filters & diverts rainwater to a storage tank. Leaves, moss & other debris are washed through to the drain or soakaway. Rainwater enters the inlet connection in the side of the unit. The inlet is designed to swirl the water in a vortex like action around the surface of the stainless steel filter below. The rainwater is drawn through the vertical mesh walls of the fine filter by adhesion, then collected & fed through the outlet to the storage tank. Debris & particles that are too large for the filter are flushed through to the drain outlet by the action of water flowing down the surface of the filter. More than 95% of the rainwater entering the filter is filtered & collected by this principle. Pitched roofs of slate, clay or concrete are the most suitable for collecting rainwater. Flat roofs can also be utilised but the volume of water collected is reduced. Thatch or planted roof areas are less suitable due to the low collection efficiency & discolouration of the water that is collected. Read about how this filter was installed as part of the rainwater harvesting system that Gutter Mate installed at  Richmond Park   Technical

Specification Suitable for roof areas up to 200 square metres Connects to standards storm water pipes below ground Virtually all debris, moss, leaves, insects, etc. is washed through the uniquely constructed vertical filter by self-cleaning action Unique oxygen-enriching function No restriction or obstruction of water flow through the appliance More than 95% efficient Minimum maintenance Tough polyethylene housing High quality stainless steel filter mesh 50cm extension tube can be trimmed to length to suit invert level Can also be wall-mounted Boxed

Dimensions & gross weights 100mm Filter
- 16kg 15 x 48 x 36 cm




...

The Large Vortex Rainwater Collection Filters for Barns & Warehouses can be installed as part of a rainwater harvesting system where rain water from the roof is channelled through a horizontal underground pipe.  It is suitable for filtering large amounts of rainwater. The unit filters & diverts rainwater to a storage tank. Leaves, moss & other debris are washed through to the drain or soakaway. Rainwater enters the inlet connection in the side of the unit. The inlet is designed to swirl the water in a vortex like action around the surface of the stainless steel filter below. The rainwater is drawn through the vertical mesh walls of the fine filter by adhesion, then collected & fed through the outlet to the storage tank. Debris & particles that are too large for the filter are flushed through to the drain outlet by the action of water flowing down the surface of the filter. More than 95% of the rainwater entering the filter is filtered & collected by this principle. Pitched roofs of slate, clay or concrete are the most suitable for collecting rainwater. Flat roofs can also be utilised but the volume of water collected is reduced. Thatch or planted roof areas are less suitable due to the low collection efficiency & discolouration of the water that is collected. Read about how this filter was installed as part of the rainwater harvesting system that Gutter Mate installed at  Richmond Park.   Technical

Specification Suitable for roof areas up to 200 square metres. Connects to standards storm water pipes below ground. Virtually all debris, moss, leaves, insects, etc. is washed through the uniquely constructed vertical filter by self-cleaning action. Unique oxygen-enriching function. No restriction or obstruction of water flow through the appliance. More than 95% efficient. Minimum maintenance. Tough polyethylene housing. High quality stainless steel filter mesh. 50cm extension tube can be trimmed to length to suit invert level. Can also be wall-mounted. Boxed

Dimensions & gross weights 150mm Filter
- 18kg 40 x 72 x 58 cm Wall Bracket
- 4kg 15 x 48 x 36 cm





...

The Large Vortex Rainwater Collection Filters for Barns & Warehouses can be installed as part of a rainwater harvesting system where rain water from the roof is channelled through a horizontal underground pipe.  It is suitable for filtering large amounts of rainwater. The unit filters & diverts rainwater to a storage tank. Leaves, moss & other debris are washed through to the drain or soakaway. Rainwater enters the inlet connection in the side of the unit. The inlet is designed to swirl the water in a vortex like action around the surface of the stainless steel filter below. The rainwater is drawn through the vertical mesh walls of the fine filter by adhesion, then collected & fed through the outlet to the storage tank. Debris & particles that are too large for the filter are flushed through to the drain outlet by the action of water flowing down the surface of the filter. More than 95% of the rainwater entering the filter is filtered & collected by this principle. Pitched roofs of slate, clay or concrete are the most suitable for collecting rainwater. Flat roofs can also be utilised but the volume of water collected is reduced. Thatch or planted roof areas are less suitable due to the low collection efficiency & discolouration of the water that is collected. Read about how this filter was installed as part of the rainwater harvesting system that Gutter Mate installed at  Richmond Park   Technical

Specification Suitable for roof areas up to 200 square metres Connects to standards storm water pipes below ground Virtually all debris, moss, leaves, insects, etc. is washed through the uniquely constructed vertical filter by self-cleaning action Unique oxygen-enriching function No restriction or obstruction of water flow through the appliance More than 95% efficient Minimum maintenance Tough polyethylene housing High quality stainless steel filter mesh 50cm extension tube can be trimmed to length to suit invert level Can also be wall-mounted Boxed

Dimensions & gross weights 150mm Filter
- 18kg 40 x 72 x 58 cm




...

This  Large Wooden Store for Heavy Duty Firewood Storage by Charles Bentley is made from treated treated nordic spruce wood so that it is protected against rot so that you don't have to worry about its durability. The raised floor will allow for effective air circulation to have dry logs for use later while the slanted roof aids in protecting the storage unit from the weather. A kindling shelf is included which can be drilled to the log store at your required height.

Features:. 1 X Kindling Shelf . Pressure Treated Wood . Slatted Design & Slanted Roof . Raised Floor Allowing Air Circulation.  Approximate dimensions: H 1520mm x W 560mm x D 1770mm 

...

This Layflat 1050 Litre Rectangular Baffled Water Butt in Millstone Grit is ideal for storing under decking or in limited spaces. Made with extra strength & durability designed to last. Holds 1050 ltrs of water & can be used easily & simply by attaching the tap to the water tank & using the water when needed. You can attach a garden hose to the tap & feed larger & further away areas easily. Made from medium density polyethylene our new 1050 ltr comes with an 8" vented lid & 1" bsp outlet which is ideal for connecting a garden tap or even connecting water butts together. Water Butt Dimensions Height 670mm Length 1500mm Width 1200mm Capacity 1050  Litres Outlet 1" BSPInlet 8" Screwdown Lid Weight empty 65 Kgs Water Tank Features 1" BSP Outlet 8" Lid Strong MDPE Corrosion Resistant No Maintenance   ...

This Layflat 1050 Litre Rectangular Baffled Water Butt in Green Marble is ideal for storing under decking or in limited spaces. Made with extra strength & durability designed to last. Holds 1050 ltrs of water & can be used easily & simply by attaching the tap to the water tank & using the water when needed. You can attach a garden hose to the tap & feed larger & further away areas easily. Made from medium density polyethylene our new 1050 ltr comes with an 8" vented lid & 1" bsp outlet which is ideal for connecting a garden tap or even connecting water butts together. Water Tank

Features: 1" BSP Outlet 8" Lid Strong MDPE Corrosion Resistant No Maintenance Dimensions: Height 670mm Length 1500mm Width 1200mm Capacity 1050  Litres Outlet 1" BSPInlet 8" Screwdown Lid Weight empty 65 Kgs

...

The Leachate Hose Extension Kit for Aerobins makes extracting liquid fertiliser (leachate), high in nutrients for your garden plants, from compost much easier. It fits onto the bottom of the 200L, 400L & 600L Aerobins & it means that you can take out the liquid accumulated in the base of the bin. This kit is supplied with 1 metre of hose which can be cut to length. Parts are supplied for self-assembly. Heating the hose end in hot (not boiling) water will ease the assembly process. THIS PRODUCT IS INCLUDED FREE OF CHARGE WITH EVERY AEROBIN PURCHASED! ...

Transform garden leaves into leaf mould using this Leafmould Compost Net, which is perfect for collecting leaves in the autumn. Leaves benefit by being exposed to rain & frost & eventually rot down to make excellent leaf mould. Most leaves take 1-3 years to rot down & take up valuable space in the compost bin & will still be in the compost when all else has matured. ...

Lid for 200L Garden Lake (Cloudburst) Water Butt Made from Black Recycled Plastic  Dimensions: Diameter (mm)
- 660 Height (mm)-
...