Trend KWJ700 KWJ700 Kitchen Worktop Jig 700mm The Trend KWJ700 Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that cuts both parts of the joint in 15 minutes including setting up. Trade all in one jig for joining worktops up to 700mm wide with a router.

Features: Left hand & right hand corners, 400mm radius peninsular joint, 45 degree end cut with slight radius, 45 degree trade corner solution for hob units, 100mm radius corner, 40mm radius corner, 35mm kitchen door hole & 3/4inch BSP hole for mixer taps Fixed lengths for 250mm, 300mm, 400mm, 500mm, 550mm, 600mm, 616mm, 650mm & 700mm wide worktops Cuts up to 40mm thick worktops with or without anti-drip postformed edge Three open-ended bolt recesses (dog bone style) for 150mm bolts Engraved lines for short 65mm bolts & worktop cross-cut 10mm diameter plastic pins with tapered shoulder for tight fit provides three point pin contact to ensure ease of setting up Engraved markings for identification of pin holes Pins made from ABS plastic for strength 9 Functions: Female cut Male cut Connector bolt recess Curved peninsular 45° end cut R40mm corner radius R100mm corner radius 45° mitre corner joint 35mm circular hinge & 3/4" BSP hole Comes with: 6 x ABS Plastic Pins Jig requires: A portable plunge router with 12.7mm (1/2 inch) shank capacity & minimum 1300 watts A template guide bush with 30mm outside diameter A TCT router cutter with 12.7mm (1/2 inch) diameter & 50mm (2 inch) cut length Two clamps

...

Trend KWJ900 Kitchen Worktop Jig (900mm) The Trend KWJ900 Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that cuts both parts of the joint in 15 minutes including setting up. Trade all in one jig for joining worktops up to 900mm wide with a router.

Features: Left hand & right hand corners, 400mm radius penisular joint, 45 degree end cut with slight radius, 45 degree trade corner solution for hob units, 100mm radius corner, 40mm radius corner, 35mm kitchen door hole & 3/4inch BSP hole for mixer taps Fixed lengths for 400mm, 500mm, 550mm, 600mm, 616mm, 650mm, 700mm & 900mm wide worktops Cuts up to 40mm thick worktops with or without anti-drip postformed edge Three open-ended bolt recesses (dog bone style) for 150mm bolts Engraved lines for short 65mm bolts & worktop cross-cut 10mm diameter plastic pins with tapered shoulder for tight fit provides three point pin contact to ensure ease of setting up Engraved markings for identification of pin holes Comes with pins made from ABS plastic for strength 9 Functions: Female cut Male cut Connector bolt recess Curved peninsular 45° end cut R40mm corner radius R100mm corner radius 45° mitre corner joint 35mm circular hinge & 3/4" BSP hole

...

Trend LOC/BLK/PK1 Loc Block Support Pack (anti Slip)

Features: Trend Loc block workpiece Pack of four interlocking

...

Trend LOCK/JIG Lock Jig complete with guide bush collar, face plate templates & mortise templates

Features:

...

Trend LOCK/JIG/B Adjustable Trade Lock Jig This Trend Adjustable Trade Lock Jig has adjustable sliding inserts to allow faceplate & mortise recesses for popular size door locks to be routed with a plunge router. It is quick & easy to set up using engraved lines for lock size & door sizes. It provides fast, clean & accurate results on doors even in hardwood. Deeper mortises can be achieved with a suitable size of auger bit. This lock jig is made from a Plastic laminate body with aluminium clamping bar, with clamping range 30mm to 80mm.

Features: Fully adjustable for lock face plate length up to 250mm. Quick & easy to set up using engraved lines for lock size & door sizes Fast, clean & accurate results on doors even in hardwood Engraved for 16mm & 19mm lock width & 22.5mm & 25.4mm face plate widths Measuring required for other lock widths Engraved on underside to allow set up for 35mm, 40mm, 44mm & 54mm door widths Deeper mortises can be achieved with a suitable size of auger bit Plastic laminate body with aluminium clamping bar, with clamping range 30mm to 80mm   Comes With: 2 x setting block Door thickness min.: 30 mm Door thickness max.: 80 mm Faceplate length min.: 30 mm Faceplate length max.: 250mm Face Plate Dimension Engraved Widths: 22.5 mm and 25.4 mm (1 inch) Mortise Dimension Engraved Widths: 16 mm (5/8 inch) & 19 mm (3/4 inch)

...

Trend M/P2P01 Point To Point Up To 600mm

Features: Instantly locate positions for dowels, screws, biscuits.

...

Trend M/PB01 Perfect Butt Worktop Scriber Tool

Features: The world's fastest professional worktop scriber tool

...

Trend MS/PRO Multiscribe Profile Matching Tool
- 15 Functions The multiscribe is a profile matching tool used to transfer contours
...

Trend PB/22 Planer Blade 82mm

Features: Trend solid carbide planer blade Will fit portable electric planers

...

Trend PB/25 Planer Blade 80mm

Features: Trend solid carbide planer blade Fits portable electric planers & are

...