Makita HR3210C Hammer Drill SDS+ Rotary, complete with side handle, depth stop, bit grease & carrying case Makita's AVT (Anti-Vibration Technology) works from the vibration the drill creates. A built in balancer moves in the oposite direction from the piston providing the hammer action, thus cancelling out the majority of vibration being transferred back through the machine. A spring loaded shock absorbing grip cushions the operator further. The HR3210C has a variable speed control & is fitted with a torque limiter device that instantly disengages the drive should the drill bit or core snag during operation. This action protects both the operator from physical injury & the machine from mechanical & electrical overload.

Features: Powered by an 850watt motor & generating 6.4 joules of impact energy & with up to 3, 300 blows per minute available, the new Makita HR3210C AVT will punch a 32mm hole into concrete & drive a 90mm CT core cutter This 3-function machine provides rotary-only operation for drilling with a no load speed of between 315 & 630rpm Rotary action with hammer support can be selected as can pure hammer-only action for heavy-duty breaking & demolition work The HR3210C has a variable speed control & is fitted with a torque limiter device that instantly disengages the drive should the drill bit or core snag during operation This action protects both the operator from physical injury & the machine from mechanical & electrical overload Two unique Makita features contribute to the super-safe, low vibration benefits of this new, advanced machine The patented Makita, AVT Anti Vibration Technology system uses the pneumatic pressure generated in the hammer piston chamber to move a counter balance in the opposite direction to dampen out the impact vibrations at the steel point This dramatically reduces machine produced vibrations. In addition to the advanced AVT system, this new Makita 5kg hammer features the 2-Mass fulcrum hinged rear grip handle & the vibration damping side handle to further limit HAV risks Comes with: Side handle Depth stop Bit grease Carry case

...

Makita HR3210C Hammer Drill SDS+ Rotary, complete with side handle, depth stop, bit grease & carrying case Makita's AVT (Anti-Vibration Technology) works from the vibration the drill creates. A built in balancer moves in the oposite direction from the piston providing the hammer action, thus cancelling out the majority of vibration being transferred back through the machine. A spring loaded shock absorbing grip cushions the operator further. The HR3210C has a variable speed control & is fitted with a torque limiter device that instantly disengages the drive should the drill bit or core snag during operation. This action protects both the operator from physical injury & the machine from mechanical & electrical overload.

Features: Powered by an 850watt motor & generating 6.4 joules of impact energy & with up to 3, 300 blows per minute available, the new Makita HR3210C AVT will punch a 32mm hole into concrete & drive a 90mm CT core cutter This 3-function machine provides rotary-only operation for drilling with a no load speed of between 315 & 630rpm Rotary action with hammer support can be selected as can pure hammer-only action for heavy-duty breaking & demolition work The HR3210C has a variable speed control & is fitted with a torque limiter device that instantly disengages the drive should the drill bit or core snag during operation This action protects both the operator from physical injury & the machine from mechanical & electrical overload Two unique Makita features contribute to the super-safe, low vibration benefits of this new, advanced machine The patented Makita, AVT Anti Vibration Technology system uses the pneumatic pressure generated in the hammer piston chamber to move a counter balance in the opposite direction to dampen out the impact vibrations at the steel point This dramatically reduces machine produced vibrations. In addition to the advanced AVT system, this new Makita 5kg hammer features the 2-Mass fulcrum hinged rear grip handle & the vibration damping side handle to further limit HAV risks Comes with: Side handle Depth stop Bit grease Carry case

...

Makita HR 3210 FCT SDS+ Rotary Hammer with Quick Change Chuck & Adapter The Makita HR3210FCT has been designed to feature low vibration level & has a lightweight design. This model features a quick change drill chuck & LED job light.

Features: 3 Mechanical gears Variable speed trigger Constant speed underload Torque limiter Job light Rotary only function Rotary hammer function Hammer only function Double insulated Powered by an 850watt motor & generating 4.9 joules of impact energy & with up to 3, 300 blows per minute available, the new Makita HR3210FCT AVT will punch a 32mm hole into concrete & drive a 90mm CT core cutter. This 3-function machine provides rotary-only operation for drilling with a no load speed of between 315 & 630rpm. Rotary action with hammer support can be selected as can pure hammer-only action for heavy-duty breaking & demolition work. The HR3210FCT has a variable speed control & is fitted with a torque limiter device that instantly disengages the drive should the drill bit or core snag during operation. This action protects both the operator from physical injury & the machine from mechanical & electrical overload. Two unique Makita features contribute to the super-safe, low vibration benefits of this new, advanced machine. Comes with: Side handle Depth stop Bit grease Quick change chuck & adaptor Carry case [http://www.youtube.com/watch?v=h Ky 0r S3xs 7A] Max Bit Diameter
- 32mm Max Core Diameter
- 90mm Impact energy
- 4.9J Blows per Minute
- 1, 650-3, 300bpm No Load Speed
- 315-630rpm Input Wattage
- 850w Net Weight
- 4.9kg








...

Makita HR3540C 35mm SDS Max Rotary Hammer Drill with AVT, complete with side handle, depth stop, bit grease & carrying case



...

Makita HR4001C SDS-MAX rotary demolition hammer drill complete with carrying case, bit grease, depth rod & side handle The Makita HR4001C is easy & comfortable to use. With slide lock-on switch it leaves operators fingers out of effort to keep pulling trigger for long hours when hammering.

Features: Dual operation mode
- Rotary Hammer & Hammer only Electronic-power-control for greater comfort Torque-limiter for additional operator protection Low vibration enables prolonged use Soft start Variable speed Constant speed under load Double insulation Comes with: Carry case Side handle Depth stop Grease Impact energy: 6.8 J Max in concrete: 40 mm Max core diameter (TCT): 105 mm Blows per minute: 1350-2750 bpm Vibration K factor: 2.5 m/sec


...

Makita HR4013C Rotary Hammer with SDS max & AVT, complete with carrying case, bit grease, depth rod & side handle The Makita HR4013C was developed to provide higher operating efficiency & more comfort with unrivalled low level of vibration. Compared to the previous model HR4011C this machine gives 20% higher drilling efficiency & 45% higher chipping efficiency. With Rotary Hammer 4.5m/sec ...

Makita HR4013C Rotary Hammer with SDS max & AVT, complete with carrying case, bit grease, depth rod & side handle The Makita HR4013C was developed to provide higher operating efficiency & more comfort with unrivalled low level of vibration. Compared to the previous model HR4011C this machine gives 20% higher drilling efficiency & 45% higher chipping efficiency. With Rotary Hammer 4.5m/sec ...

Makita HR4511C SDS Max Rotary Demolition Hammer Drill with AVT, complete with 2 side handles, depth stop, bit grease & carrying case This Demolition Hammer features Makita's Anti Vibration Technology which dramatically cuts down the amount of vibration being transferred to the operator resulting in much less user fatigue. This works with an internal balancer which is moved by the air pressure created inside the drill housing by the hammer action. The balancer moves in the oposite direction thus acting as a perfectly timed counterbalance. This technology coupled with the padded, spring loaded, hinged rubberised grip means the HR4511C is unleashing all it's power in a forward motion, enabling it to be used for long periods of time with little vibration transferral to hands & arms.

Features: Reduced vibration for less operator fatigue (AVT) Torque-Limiter
- when drill hits reinforcement the Torque-Limiter stops power 16 Angle Settings of Chisel Bit
- for added control LED lights
- Green drill is electrified & flashing Red signifies brushes needing changed Recessed Change Lever
- mounted on top of machine to reduce breakage even if machine is dropped or laid down carelessly Constant speed underload. Rotary hammer action. Hammer only action
- no hammering while idling for longer machine life Double insulated
- for extra safety Comes with: 2 Side handles Depth stop Bit grease Carrying case Max in Concrete: 45mm Core Bit Diameter (TCT): 125mm Joules: 13 Js Blows per minute: 1, 250-2, 750bpm No Load Speed: 130-280rpm Input wattage: 1, 350w Vibration: 7.5m/sec HO.7.0m/sec D handle Tri-Axial Net Weight: 8.4kg







...

Makita HR4511C SDS Max Rotary Demolition Hammer Drill with AVT, complete with 2 side handles, depth stop, bit grease & carrying case This Demolition Hammer features Makita's Anti Vibration Technology which dramatically cuts down the amount of vibration being transferred to the operator resulting in much less user fatigue. This works with an internal balancer which is moved by the air pressure created inside the drill housing by the hammer action. The balancer moves in the oposite direction thus acting as a perfectly timed counterbalance. This technology coupled with the padded, spring loaded, hinged rubberised grip means the HR4511C is unleashing all it's power in a forward motion, enabling it to be used for long periods of time with little vibration transferral to hands & arms.

Features: Reduced vibration for less operator fatigue (AVT) Torque-Limiter
- when drill hits reinforcement the Torque-Limiter stops power 16 Angle Settings of Chisel Bit
- for added control LED lights
- Green drill is electrified & flashing Red signifies brushes needing changed Recessed Change Lever
- mounted on top of machine to reduce breakage even if machine is dropped or laid down carelessly Constant speed underload. Rotary hammer action. Hammer only action
- no hammering while idling for longer machine life Double insulated
- for extra safety Comes with: 2 Side handles Depth stop Bit grease Carrying case Max in Concrete: 45mm Core Bit Diameter (TCT): 125mm Joules: 13 Js Blows per minute: 1, 250-2, 750bpm No Load Speed: 130-280rpm Input wattage: 1, 350w Vibration: 7.5m/sec HO.7.0m/sec D handle Tri-Axial Net Weight: 8.4kg







...

Makita HR5212C Demolition Hammer Rotary Drill SDS Max with AVT comes complete with 2 side handles & depth stop The Makita HR5212C features AVT has been developed to provide higher operating efficiency & more comfort with unrivalled low levels of vibration. Makita's Anti Vibration Technology which dramatically cuts down the amount of vibration being transferred to the operator resulting in much less user fatigue. This works with an internal balancer which is moved by the air pressure created inside the drill housing by the hammer action. The balancer moves in the oposite direction thus acting as a perfectly timed counterbalance. A spring loaded shock absorbing handle cushions the operator further.

Features: Active dynamic vibration absorber Vibration absorbing housing Soft start " Soft no load" function automatically reduces the motor speed during idling to suppress the vibration of the machine body Torque limiter Constant speed control Ergonomic soft grip Variable speed control dial One touch sliding chuck for easy bit installation & removal LED service & power warning lights Dual operation mode: Rotary Hammer & Hammer Only Compatible with dust extractor attachment Comes with: Carry case 2 x side handles Depth stop Bit grease Cleaning cloth [https://www.youtube.com/watch?v=xf_t 5kk G It 0] Impact energy 19.1 J Max in concrete 52 mm Impacts per minute 1100
- 2250 ipm Input Wattage 1510 w Max core diameter (TCT) 160 mm Vibration K factor 1.5 m/sec


...