Pole to pole exterior car care is now available in this beautiful pack, making the perfect gift for anyone who cares for their car. The Polar Collection comprises all three Polar Series products in 500ml trial sizes. Let someone you love pre-wash, wash & protect their loved one using their pressure washer!
Includes:: Polar Blast 500ml Polar Wash 500ml Polar Seal 500ml Polar Blast Before you start, check that the bodywork & wheels are cool to the touch & out of direct sunlight. Polar Blast can be used at various dilutions depending on the density of foam desired. A good starting point is 100ml product to 500ml water in your foaming bottle. Adjust foam gun settings as required to increase or reduce foam. Spray Polar Blast onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass & wheels. Leave Polar Blast time to dwell & loosen dirt for up to 10 minutes, although do not allow it to dry on. Finally, rinse thoroughly from the bottom up. Polar Wash Before you start, check that the bodywork & wheels are cool to the touch & out of direct sunlight. We recommend a pre-wash with Polar Blast to gently loosen dirt. If not, rinse first with water to loosen heavy contamination. Polar Wash can be used at various dilutions depending on the density of foam desired. However, we would not recommend using a dilution stronger than 50:50. Adjust foam gun settings as required to increase or reduce foam. 250ml of mixed solution should be enough to cover an average sized car. Spray Polar Wash onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass & wheels. The cleaner will begin to loosen dirt on all surfaces. For the most thorough clean we recommend agitating the foam with a sponge or wash mitt. Rinse thoroughly from the bottom up & dry. Polar Wash is not suitable for use on soft top convertibles. Top Tip Follow with Polar Seal for a protective, hydrophobic coating Polar Seal Before you start, check that the bodywork & wheels are cool to the touch & out of direct sunlight. We recommend starting with a snow foam like Polar Blast to gently loosen dirt, & follow with Polar Wash to remove any dirt or contamination on your paintwork. Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle & then add at least 200ml of water. This should be all the finished solution required to cover your vehicle. There is no benefit in using any more than 40ml as over application can compromise the finish. Spray Polar Seal onto the clean, wet vehicle, ensuring all exterior surfaces are covered, although avoid direct application to the windscreen. Thoroughly rinse & dry your car to reveal a high-gloss finish that is protected with a hydrophobic coating. The car must be dried with a cloth & not allowed to air dry as water spotting may occur. Use Autoglym Fast Glass to clean the windscreen & wiper blades to ensure no smearing occurs. We do not recommend applying more than once a month. Polar Seal is not suitable for use on soft top convertibles. Do not store diluted product. Please rinse foam bottle & pressure washer lance after use. Top Tip For the optimum finish, dry with the Autoglym Insta Dry cloth.
...

A protective, hydrophobic coating, for a quick & easy high-gloss finish. Polar Seal is a protective coating that has been specially formulated for application through a pressure washer with a foam gun. It imparts a hydrophobic layer onto paintwork that causes water to bead on the surface, which reduces the time it takes to dry the car. Simply spray onto a clean, wet vehicle, rinse off & dry to leave behind a high gloss finish. How to use this product Before you start, check that the bodywork & wheels are cool to the touch & out of direct sunlight. We recommend starting with a snow foam like Polar Blast to gently loosen dirt, & follow with Polar Wash to remove any dirt or contamination on your paintwork. Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle & then add at least 200ml of water. This should be all the finished solution required to cover your vehicle. There is no benefit in using any more than 40ml as over application can compromise the finish. Spray Polar Seal onto the clean, wet vehicle, ensuring all exterior surfaces are covered, although avoid direct application to the windscreen. Thoroughly rinse & dry your car to reveal a high-gloss finish that is protected with a hydrophobic coating. The car must be dried with a cloth & not allowed to air dry as water spotting may occur. Use Autoglym Fast Glass to clean the windscreen & wiper blades to ensure no smearing occurs. We do not recommend applying more than once a month. Polar Seal is not suitable for use on soft top convertibles or motorcycles. Do not store diluted product. Please rinse foam bottle & pressure washer lance after use. Top Tip: For the optimum finish, dry with the Autoglym Insta Dry cloth. FAQ's What is Polar Seal? It is a coating designed specifically for use in a pressure washer. It is the coating element (third & final stage) of the three-stage Polar range process. It is preceded by the prewash Polar Blast & shampoo
- Polar Wash. Is Polar Seal wax safe? Polar Seal is wax safe & we would recommend that if there is wax on the paintwork that Polar Seal is used as a top up. There is no need to remove the wax or other protection before applying Polar Seal. Is Polar Seal p H Neutral? Polar Seal is p H Neutral & can be used on full exterior of the vehicle, avoiding the windscreen. Do I use Polar Seal instead of a wax? Polar Seal is a durable hydrophobic coating. However, it does not offer the same long-term protection as Ultra High Definition Wax or Extra Gloss Protection. Should I agitate the foam once I have applied Polar Seal? No, it is not necessary. The vehicle should be clean before applying Polar Seal, ideally with Polar Blast & Polar Wash. Polar Seal should be sprayed over all exterior surfaces apart from the windscreen & then rinsed off immediately. What is the recommended Dilution rate for Polar Seal? We would strongly recommend not using more than 40ml Polar Seal & 200ml water. Over use may cause white spotting & significantly compromise the effectiveness of Polar Seal. Using more product will not improve the depth of shine or increase its durability. Why is it not recommended to use on the windscreen? Polar Seal contains silicones, which in some cases, can create smears once wiper blades are used on the windscreen. We would recommend cleaning your windscreen after you have applied Polar Seal to the rest of your car as part of your car cleaning process. How long should I leave Polar Seal on my paintwork? It is important that Polar Seal does not dry on to the surface of the vehicle. Once the car has been coated it should be rinsed immediately. Can Polar Seal be used on my alloys & exterior plastics? Yes, apart from the front windscreen we would recommend Polar Seal can be used on all exterior surfaces. Is it ok to leave Polar Seal in my foamer bottle? We would recommend that only the product needed for a single application is used. We also recommend that the foamer bottle is rinsed thoroughly after use. How frequently do I need to apply Polar Seal? There is no benefit to building layers of Polar Seal. We would only recommend reapplication once water beading has ceased. We certainly do not recommend application more than once a month.
...

A safe & effective cleaner for home pressure washers. Polar Wash is a safe & effective cleaner that should be applied using a pressure washer with a foam gun after pre-washing with a snow foam such as Polar Blast. This impressive cleaner will cover your vehicle in a blanket of foam that makes light work of dirt, traffic film & road grime removal. How to use this product Before you start, check that the bodywork & wheels are cool to the touch & out of direct sunlight. We recommend a pre-wash with Polar Blast to gently loosen dirt. If not, rinse first with water to loosen heavy contamination. Polar Wash can be used at various dilutions depending on the density of foam desired. However, we would not recommend using a dilution stronger than 50:50. Adjust foam gun settings as required to increase or reduce foam. 250ml of mixed solution should be enough to cover an average sized car. Spray Polar Wash onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass & wheels. The cleaner will begin to loosen dirt on all surfaces. For the most thorough clean we recommend agitating the foam with a sponge or wash mitt. Rinse thoroughly from the bottom up & dry. Polar Wash is not suitable for use on soft top convertibles. Top Tip Follow with Polar Seal for a protective, hydrophobic coating FAQ's What is Polar Wash? It is a shampoo designed specifically for use in a pressure washer. It is intended to be the wash element (second stage) of the three-stage Polar range process. It is preceded by the prewash Polar Blast & followed by a coating
- Polar Seal. How is Polar Wash different from Pressure Wash? Polar Wash replaces Pressure Wash, our previous pressure washer shampoo. The formulation has been reformulated & is stronger than its predecessor. How is Polar Wash different to Polar Blast? Polar Blast is a Pre-Wash product that aids the removal of heavy dirt from the paintwork. It gently loosens & softens contaminants & does not require agitation. Polar Wash is the next stage of the process the shampoo. It has more cleaning power that can get to work on removing traffic film once Polar Blast has removed the larger particles of contamination. Is Polar Wash p H neutral? No it isnt. However it will not remove Extra Gloss Protection, Waxes or sealants; such as Life Shine. Can Polar Wash be used neat or does it need to be diluted? Yes it can be used neat. However we would recommend a 50:50 dilution rate for the best results. It is up to the user to find a dilution the best works for them. Can Polar Wash be added to the reservoir in my Jet Wash? Yes. However, it is worth highlighting that the level of foam will be dependent on the performance & flow rates of the pressure washer & water hardness. The 50:50 product/water mix advised for a bottle foamer is also a good starting point for a reservoir. Is Polar Wash High Foaming? Yes, it is a high foaming product that allows the user to see where they have agitated the product to minimise chances of missing a bit. However, although this product has greater cleaning power, its foam does not have the density & cling time of our pre-wash product
- Polar Blast. Is Polar Wash a touchless wash shampoo? It can perform a touchless clean on very lightly soiled & well maintained vehicles. However, for stubborn dirt & traffic film we advise agitation with a wash mitt or sponge. Does Polar Wash need to be used through a pressure washer? Polar Wash has been designed specifically for use through a pressure washer. We would recommend our other shampoos for hand washing methods. Is a foaming lance required to use Polar Wash? We would strongly recommend the use of a foaming lance or foamer bottle in conjunction with a pressure washer to create the optimum foam levels.

...

A foaming shampoo that quickly removes everyday contaminants for a streak free finish Squeaky clean paintwork is an essential part of the car care routine. Pure Shampoo is an easy to use & safe p H neutral formulation. Its rich foam quickly breaks down & removes everyday contaminants from your vehicle. Pure Shampoo is a high foaming, p H neutral, pure shampoo that cleans the car extremely well, but doesnt do anything else. It leaves no film behind, nor does it have any other additives. The lack of gloss enhancers, wax or similar additives makes it suitable for cleaning matt or satin finishes. Pure Shampo is wax safe. For a long lasting shine, finish with Rapid Aqua Wax. Previously called Bodywork Shampoo. How to use this product Shake well. Pour 2 capfuls into a bucket & add 10 litres of water. Hose bodywork before you start to rinse away excess dirt. Always work on a cool surface, shampooing the car from the roof down. Do not allow the shampoo to dry on the car. Rinse well with clean water & dry with a Microfibre Drying Towel to prevent water spots. If you are using Rapid Aqua Wax, there is no need to dry the car. FAQ's Q: Is Pure Shampoo wax & sealant safe? A: Yes, Pure Shampoo will not wash away or strip wax or sealants. Q: Is Pure Shampoo PH Neutral? A: Yes, Pure Shampoo Conditioner is a PH neutral shampoo. Q: Can I apply Pure Shampoo through a pressure washer? A: Pure Shampoo can be applied through a pressure washer however you may like to use our bespoke product, the Autoglym Polar Series as an alternative as this has been specifically formulated for use with pressures washers. Q: Should I use warm or cold water with Pure Shampoo? A: You can use warm or cold water, whichever you prefer. Avoid very hot water as it can cause the shampoo to dry on the vehicle surface. ...

A foaming shampoo that quickly removes everyday contaminants for a streak free finish Squeaky clean paintwork is an essential part of the car care routine. Pure Shampoo is an easy to use & safe p H neutral formulation. Its rich foam quickly breaks down & removes everyday contaminants from your vehicle. Pure Shampoo is a high foaming, p H neutral, pure shampoo that cleans the car extremely well, but doesnt do anything else. It leaves no film behind, nor does it have any other additives. The lack of gloss enhancers, wax or similar additives makes it suitable for cleaning matt or satin finishes. Pure Shampo is wax safe. For a long lasting shine, finish with Rapid Aqua Wax. Previously called Bodywork Shampoo. How to use this product Shake well. Pour 2 capfuls into a bucket & add 10 litres of water. Hose bodywork before you start to rinse away excess dirt. Always work on a cool surface, shampooing the car from the roof down. Do not allow the shampoo to dry on the car. Rinse well with clean water & dry with a Microfibre Drying Towel to prevent water spots. If you are using Rapid Aqua Wax, there is no need to dry the car. FAQ's Q: Is Pure Shampoo wax & sealant safe? A: Yes, Pure Shampoo will not wash away or strip wax or sealants. Q: Is Pure Shampoo PH Neutral? A: Yes, Pure Shampoo Conditioner is a PH neutral shampoo. Q: Can I apply Pure Shampoo through a pressure washer? A: Pure Shampoo can be applied through a pressure washer however you may like to use our bespoke product, the Autoglym Polar Series as an alternative as this has been specifically formulated for use with pressures washers. Q: Should I use warm or cold water with Pure Shampoo? A: You can use warm or cold water, whichever you prefer. Avoid very hot water as it can cause the shampoo to dry on the vehicle surface. ...

Used at some of the worlds most exclusive automotive events to quickly remove light dirt & fingerprints Rapid Detailer removes light dirt, restores shine & leaves a layer of polymeric protection on surfaces. It is a superior maintenance product for all exterior surfaces, including paintwork, rubber, plastic, chrome, carbon fibre & glass. It can also be used as a clay bar lubricant. If your car is in between clean & dirty, Rapid Detailer is perfect. It will not remove or affect polishes, waxes or sealants & actually tops up existing protection. You can also apply it to rubber, plastic, bare metal & chrome. If you have driven your car to a show, or are displaying it somewhere, this is perfect to get it back to 100%. If you have ever seen us maintaining cars at a show, we will have been using Rapid Detailer, it is our go to product. Team up with a Hi-Tech Finishing Cloth & it is the perfect maintenance duo. Rapid Detailer is also an excellent clay bar lubricant & comes as part of the Surface Detailing Clay Kit. Pro Tip: If your paintwork is dull you will need to give it a wash & a polish first, & then you can use Rapid Detailer to maintain the polished finish. How to use this product For detailing: Shake well & spray sparingly onto cool surfaces. Spread over paintwork using a Hi-Tech Finishing Cloth, turning it regularly, & continue buffing to a shine. Enjoy the fruity fragrance. As a clay lubricant: Follow the instructions given with the Surface Detailing Clay Bar. Ensure continuous lubrication by keeping the surface wet with Rapid Detailer. FAQ's Q: Can I use Rapid Detailer to remove greasy finger prints from my otherwise clean vehicle? A: Absolutely! Rapid Detailer is ideal for cleaning & dressing isolated areas of dirt or grease to restore a show room finish! ...

High opacity paint to improve the appearance of exterior panels & engine components Ideal additional service to improve customer satisfaction Single-coat application saves your valuable time & costs Can improve sales in showrooms & forecourts Single-coat application Excellent coverage Localised spray pattern for use in restricted areas Shake well. Ensure surfaces are clean, dry & free of loose rust. Spray evenly onto the surface. Allow each coat to dry before re-spraying. After the job is completed, invert the can & spray briefly to clear nozzle. ...

Everything you need to remove scratches from paintwork No matter how careful you are, scratches & swirls will occur. If they are too deep to remove with Super Resin Polish, a new approach is required, & that is where the Scratch Removal Complete Kit comes in. Scratch Remover has been carefully blended to achieve the optimum balance of deep cut with a high gloss finish. Important: Unfortunately not all scratches can be removed completely. If a scratch is too deep to remove by h&, its appearance can still be vastly enhanced but it may require professional rectification for complete repair. Contents: 100ml Scratch Remover 100ml Super Resin Polish Hi-Tech Finishing Cloth Scratch Removal Applicator How to use this product How to use: Shake well & apply two pea-sized amounts of Scratch Remover to the white side of the foam waffle applicator. Using firm pressure, apply Scratch Remover using an up & down then side to side motion. Only use Scratch Remover on the affected area, avoiding the surrounding paintwork if possible. After 30 seconds it is important to check your progress. Apply more product & repeat as required. Once the scratch has been removed (or significantly improved) continue to work any remaining residue with a light pressure into the area for a glossy finish. Wipe away residue using a clean microfibre cloth. Once the scratch has been removed, complete the process by polishing the rest of the car with Super Resin Polish (included) to ensure a brilliant high gloss finish. FAQ's Q: Is this product safe to use on all paint types i.e. matt or metallic? A: Scratch Remover is safe to use on solid colour & metallic paints, but should not be used on matt or satin paintwork. If you are at all unsure please contact Autoglym for guidance. Q: What is the difference between Scratch Remover & Paint Renovator? A: Autoglym Paint Renovator was originally developed to renovate paint that had oxidised, faded or aged. It was designed to work on larger panels rather than smaller scratches. It is less abrasive than Scratch Remover so is less effective at removing scratches that have penetrated the paintwork more than oxidisation. Scratch Remover has been designed specifically to remove scratches. Q: Can the product be used on glass? A: The product has been designed for removal of scratches of car paintwork. It should not be used on glass or plastic substitutes. ...

A low foam & deep cleaning shampoo with a water repellent finish for easy rinsing & ongoing protection A clean car is a thing of beauty & its easy to achieve with Bodywork Shampoo Conditioner, our hard working yet gentle, p H neutral shampoo. Our low foaming solution contains a water repellent film that causes rinse water to sheet off the surface, helping you to rinse & dry your car faster. Its active ingredients clean your vehicle without stripping away any polish or wax you have previously applied. How to use this product Shake well. Pour 2 capfuls (for the 2.5 litre bottle, only pour 1 capful) into a bucket & add 10 litres of warm or cold water. Hose bodywork to rinse away excess dirt. Always work on a cool surface, shampooing the car from the roof down. Do not allow the shampoo to dry on the car. Rinse well with clean water & dry with a Microfibre Drying Towel to prevent water spots. FAQ's Q: Why is there less foam produced from Bodywork Shampoo Conditioner than some car shampoos? A: Bodywork Shampoo Conditioner has been formulated specifically to provide a low foaming option when cleaning your vehicle. The low foaming solution contains a water repellent film that causes rinse water to sheet off the surface, helping you to rinse & dry your car faster. Q: Can I apply Bodywork Shampoo Conditioner through a pressure washer? A: Bodywork Shampoo Conditioner can be applied through a pressure washer however you may like to use the Autoglym Polar Series as an alternative as this has been specifically formulated for use with a pressure washer. Q: Should I use warm or cold water with Bodywork Shampoo Conditioner? A: You can use warm or cold water, whichever you prefer. Avoid very hot water as it can cause the shampoo to dry on the vehicle surface. ...

A low foam & deep cleaning shampoo with a water repellent finish for easy rinsing & ongoing protection A clean car is a thing of beauty & its easy to achieve with Bodywork Shampoo Conditioner, our hard working yet gentle, p H neutral shampoo. Our low foaming solution contains a water repellent film that causes rinse water to sheet off the surface, helping you to rinse & dry your car faster. Its active ingredients clean your vehicle without stripping away any polish or wax you have previously applied. How to use this product Shake well. Pour 2 capfuls (for the 2.5 litre bottle, only pour 1 capful) into a bucket & add 10 litres of warm or cold water. Hose bodywork to rinse away excess dirt. Always work on a cool surface, shampooing the car from the roof down. Do not allow the shampoo to dry on the car. Rinse well with clean water & dry with a Microfibre Drying Towel to prevent water spots. FAQ's Q: Why is there less foam produced from Bodywork Shampoo Conditioner than some car shampoos? A: Bodywork Shampoo Conditioner has been formulated specifically to provide a low foaming option when cleaning your vehicle. The low foaming solution contains a water repellent film that causes rinse water to sheet off the surface, helping you to rinse & dry your car faster. Q: Can I apply Bodywork Shampoo Conditioner through a pressure washer? A: Bodywork Shampoo Conditioner can be applied through a pressure washer however you may like to use the Autoglym Polar Series as an alternative as this has been specifically formulated for use with a pressure washer. Q: Should I use warm or cold water with Bodywork Shampoo Conditioner? A: You can use warm or cold water, whichever you prefer. Avoid very hot water as it can cause the shampoo to dry on the vehicle surface. ...