First Appeared in: RCM&E July 2009 Issue Name: Roamer Model type: Vintage R/CDesigned by: Cal Smith / Peter Miller Wingspan: 62” Fuselage length: 45.5” Wing area: 666 sq. in. All-up weight: 5 lbs Wing loading: 17oz / sq. ft. Functions (servos): Rudder (2); elevator (1); throttle (1);optional nose wheel steering (1) Rec’d engine. 25 two-stroke;. 30 four-stroke Roamer Peter Miller Rejuvenates One Of Cal Smith’s Classic Designs To Create A Model That’s Perfect For Long Summer Evenings... Better Get Building! Hot Metal You can make ballast blocks by pouring molten lead into moulds carved into blocks of wood. The moulds need to be tapered so you can get the lead out again, but more importantly the wood should be as dry as possible: damp wood will make the lead spit back, & hot lead will cause serious burns. Be warned, then, & protect yourself with thick leather gloves & safety goggles at the very least. If you have any doubts about casting lead weights, you can make up blocks by cutting sheet lead into small pieces & gluing them together. If you need some lead sheet, try scrounging it from your friendly local roofi ng contractor. ...

First Appeared in: RCM&E October 2009 Issue Name: Wave Model type: Seaplane Designed by: Ton van Munsteren Wingspan: 45” (1140mm) Fuselage length: 31” (787mm) Wing area: 2sq. ft. All-up weight: 28oz (790g) Wing loading: 14oz / sq. ft. (4.3kg / sq. m) Functions (servos): Rudder (1); elevator (1); throttle (via ESC) Rec’d motor: Typhoon 15/10 Rec’d ESC: 25
- 30amp Rec’d battery: 3s 1p 1500
- 2000m Ah Li-Po I’ve been flying R/C for over 30 years now, & whilst it’s good fun operating ‘full house’ models I still like to fl y 3-channel rudder / elevator occasionally. When pondering an own-design fl ying boat I decided that this, too, would be a rudder / elevator model, with old timer looks & powered by an electric motor spinning a 9” (or thereabouts) prop. The internet puts such a wealth of information at your fi ngertips, & it didn’t take too long to fi nd a free-flight model upon which to base my design. I used a picture of it as the wallpaper on my PC for continued inspiration, & set about designing the Wave using CAD. With the plan drawn & the prototype quickly built, I was keen to get to the water’s edge to see how she’d perform. I’d given Wave a wide, boat-shaped fuselage with a V-bottom words & photos » Ton Van Munsteren section before the step & a fl at ditto after the step, which hopefully pointed to easy taxiing & fuss-free take-offs. I’m glad to say that I was right; take-offs are as long as you like & as smooth as silk, & on only half power, too. Open the taps, & a full-power ROW only takes about five metres! Once airborne, the lack of ailerons doesn’t spoil the fun for Wave will lift her skirt & loop, roll, stall turn & do a (sort of) half Cuban 8
- just on rudder & elevator. Still interested? Then let’s get building! Article In October 2009 RCM&E


...

First Appeared in: RCM&E November 2009 Issue Name: Colomban Luciole Model type: Scale home-built Designed by: Peter Miller Wingspan: 60” Fuselage length: 431/4” Wing area: 348 sq. in. All-up weight: 64oz Wing loading: 261/2oz / sq. ft. Functions (servos): Rudder (1); elevator (1); throttle (1); aileron (2); flap (2) Rec’d engine. 18
-. 21 two-stroke, or possibly a good. 15 for flying in light winds. FAST & FRUGALThe first thing that strikes you about the Luciole is the very high aspect ratio of the wing: with a span of 221/2ft but a chord of just 26in, the wing looks like a ruler. Most of the trailing edge is taken up with very large fl aps, but the wingspan means that the small ailerons out at the tips have plenty of leverage! Between them, the flaps & ailerons take up almost a third of the chord, but the tail does better still since it has all-fl ying surfaces. The construction of the MC30 would look very familiar to most model aircraft builders, with spars, foam ribs, leading edge sheeting, cap strips & a fuselage with ply sides, a ply bottom & a stringered turtle deck. However, the lightness of this construction, when coupled with the Briggs & Stratton 650cc OHV V-twin engine, allows the Luciole to cruise at 105mph while sipping just five litres of fuel every hour. With an endurance of five hours you can do some serious travelling in this aircraft. Richard suggested that I build a model of the Luciole but I took one look at the three views & said, “ No thanks!” That wing just didn’t look suitable for the size of model that I’d build. A couple of evenings later, however, I made a few calculations & realised that it would be possible. Article in November 2009 RCM&E
...

First Appeared in: RCM&E December 2009 Issue Name: Ultimate 20-300 Model type: 3D / sport aerobat Designed by: Dave Royds Wingspan: 39” (991mm) Fuselage length: 47” (1194mm) Wing area: 4.3sq. ft. (0.4 sq. m) All-up weight: 35
- 50oz (1
- 1.4kg) Wing loading: 8
- 11oz / sq. ft. (2.4
- 3.3kg / sq. m) Functions (servos): Rudder (1); elevator (1); aileron (2); throttle (via ESC); Rec’d motor: Hacker A30-16M / Tornado 4240 Not content with the performance of his full-size Pitts Special, Canadian Aerobatic Champion Gordon Price decided to modify it like no other. Such was the interest for his bespoke Pitts components, Gordon went into production & the Ultimate Aircraft Company was born. As his product line expanded the next logical step was to produce a complete airframe, & his diminutive 10-100 bipe hit the market. Following the success of the little home-built, Gordon returned his sights to the aerobatic scene & produced a series of high performance aircraft, culminating in the fl agship 300hp, Lycomingpowered muscle bipe
- the Ultimate. Despite the Ultimate gaining in popularity & the order book fi lling up, the company hit diffi culties, forcing its doors to be closed less than a decade after it all began.WILD BLUE Although the day of the maiden dawned with a beautiful blue sky, previous days of torrential rain had turned the runway into a mud bath. Not wanting the risk a nose-over so early in the day, I decided to bite the bullet & go for a h&-launch. Gripping the top wing & with a gentle underarm push, the Ultimate eased skyward. After a few test circuits to adjust the trims, it was time to see what she could do. Throttling up into wind & pulling back on the elevator soon had the Ultimate climbing vertically
- gaining a little height & kicking the rudder & elevator over produces a very scale spin; adding a little opposite aileron levels the wings & reduces the rate of descent as she pulls into a controlled, fl at spin. Releasing the sticks & dipping the nose pulls her straight out without any over-rotation or control surface stall. Very nice. Although not designed as an out-&-out 3D machine, she’ll still handle the basic staple manoeuvres with relative ease. Prop-hanging & torque rolling requires very little in the way of corrective input, whilst walls, harriers & elevators are effortless with minimal signs of wing-rock. Knife-edge & hesitation rolls require a few degrees of top rudder to keep the nose up at low speed, but as speed increases the large side area of the fuselage keeps it tracking on the straight & level. Slow speed manners are quite exemplary; inducing a stall merely slows her to a crawl followed by a gradual, controlled descent, needing only a blip of the throttle to return to fl ying speed. Subsequent to the initial fl ights with the Hacker 16M, substituting the motor for the Tornado 4240 defi nitely upped the Ultimate’s aerobatic performance; while she’s never going to be rocket ship, the difference in acceleration & vertical punch-out were defi nitely noticeable. Article in December 2010 RCM&E





...

Designer: Mal Shepherd Name: Red Ned Model type: Motor glider Wingspan: 110.5" Fuselage length: 52.75" Wing area: 4 lbs 4oz Wing Loading: 11.5oz / sq ft Functions: (Servos): Aileron (2); throttle (1) rudder (1), throttle (1) Rec'd engine. 25 cu. in two stroke Featured in the May 2010 Issue of RCM&E. A 110.5” SPAN MOTOR GLIDER FOR. 25 cu. in ENGINES ...

Name: Rivets Model type: Semi-scale racer Designed by: Tim Hooper Wingspan: 36" Fuselage length: 34" Wing area: 238 sq. in. All-up weight: 290z Wing loading: 180z / sq. ft. Functions (servos): Aileron (1); elevato r (1); rudder (1); throttle (via ESC) Powertrain: Typhoon 15/10; APC-E 8 x 6" prop; 3s 1800m Ah Li-Po Article in July 2010 RCM&E ...

NB This item & its assocaited parts are a pre-sale item which will be available at the end of May 2010. This is the latest Tony Nijhuis design brought to you by RCM&E magazine, which will be featured in the July 2010 issue of RCM&E, onsale on 4th June 2010. DATAFILE Name: Halifax Mk.III Model type: Scale W.W.2 bomber Designed by: Tony Nijhuis Wingspan: 104" (2625mm) Fuselage length: 77.5" (1965mm) Wing area: 9.2sq. ft. (0.9sq. m) All-up weight: 23 lb (10.4kg) Wing loading: 40oz / sq. ft. (12.2kg / sq. m) Functions (servos): Aileron (2), elevator (2), throttle (4), rudder (2), retracts (1), bomb doors (2), tail wheel (1) Rec'd engines: 4 x. 30 two-stroke /. 32 four-stroke ...

RC2075 Wittman Tailwind Plan by Peter Miller The Wittman Tailwind is probably the most famous aircraft youve never heard of. Steve Wittmans cheap home-build cross-country sportster kick-started the home build boom in the 1950s & its still being built & flown today. Peter Millers 48" span model reproduces the Tailwinds pleasing lines & flies superbly well using a. 20-.25 two-stroke or four-stroke equivalent engine. The huge fuselage means an electric conversion should be easy to engineer too. The new CNC/ Laser-cut parts set speeds up the build process by reproducing the ribs, formers & other parts (apart from strip balsa) required for the model while a wood completion pack that

Includes:: the strip & sheet balsawood is also available. The cowl is made using balsa & ply. An electric conversion build blog can be found at www.modelflying.co.uk & builders can chat with designer Peter Miller in the friendly forum. Data File Name: Wittman Tailwind W-10 Model Type: Scale home-built Designed by: Peter Miller Wingspan: 48" Fuselage length: 39" Wing area: 360 sq in All-up weight: 66oz Wing loading: 26.4oz/sq ft Functions (servos): Aileron (2); elevator (1); throttle (1); rudder (1); flap (2) Recd Engine. 20-.25 two-stroke/. 26-.30 four-stroke Published in RCM&E, August 2010

...

Name: Van’s RV-3 Model type: 1/5-scale home-built Designed by: Peter Miller Wingspan: 47.5” Wing area: 510 sq. in. All-up weight: 5 lbs 14oz Wing loading: 26.5oz / sq. ft. Fuselage length: 44” Functions (servos): Ailerons (1); elevator (1); throttle (1); rudder (1); flap (1) Power. 48
-. 52 four-strokes. 32
-. 40 two-strokes Plan along with project build first published in the December 2010 Issue of RCM&E.

...

RC2079 Pix-E Major Plan by Tim Hooper Tim Hooper reinvents a classic Keil Kraft model that rekindles the spirit of aeromodellings gentler age. The 42" span Pix-E Major is for inexpensive electric power systems & three-channel control (rudder, elevator, throttle) & it flies a treat too! Its easy & relaxing to fly while very forgivving. Go on
- relive a design classic! Datafile Name: Pix-E Major Designed: Tim Hooper Wingspan: 42" Wing area: 232 sq. in. All-up weight: 13.5ozwing loading: 8.5oz / sq. ft. Functions: elevator, rudder, throttle Powersystem: 2408-21 size outrunner, 15-amp ESC, 2S 1300m Ah Li-Po battery, 9x 6 prop.
...