Designer: Stan Bray A small vertical four column steam engine to be built at minimal cost from stock materials. Presented on three Sheets, the drawings show all necessary details which are dual dimensioned in imperial & metric units for the convenience of builders with access to metric tools & equipment. ME. Vol.172. Sheet 1 General arrangement elevations & details of top, motion & baseplates & supporting pillars. Sheet 2 Cylinder components: cylinder, cylinder base, top cover & gl&, piston assembly, steam chest & cover. Sheet 3 Main bearings, connecting & valve rods, crosshead & gudgeon pin, slide valve, crankshaft & crankpin, eccentric sheaf & strap. ...

Orange Orchards by Ann Duncan Use simple strip piecing to create this cheerful throw. Finished

Size: Approx.

...

Ornamental Turning T.D. Walshaw This is the definitive guide to the art, aimed at not only the experienced woodturner but also at the novice. Tom Walshaw provides comprehensive chapters on purpose -built ornamental lathes, essential accessories, using cutting & decorative tools plus detailed information about screw threads & templates. Fully illustrated with 200 photographs 234x 156mm 208 pages Illustrated paperback ...

The Canadian One Design racing mono hull was one of the most popular racing boats in Canada. Designed in the 1950's, its simple build & low cost attracted the average working person onto the racing scene. Kit uses all laser cut parts & detailed instructions take you through the simple build process. Kit also

Includes:: the running pack which features motor to shaft coupler, thrust bearing, drive shaft, stuffing tube, prop, prop nut, rudder & mounting hardware. Scale: 1:8 Length: 559mm (22") Beam: 229mm (9") Suitable for RC. Manufacturer: Osbourne Model Kits Model: Canadian One Design (1:8 Scale Inc Drive Kit) (OSB-2509)

...

Constructed in the same manner as the full sized Mirror Dinghy, this 1:6 scale radio controlled model sailboat kit is a scale builder's dream! The kit features laser cut wood parts, scale rudder (with working tiller), removable centreboard, pre-sewn sails, detailed instructions, pre-cast ballast bulb, working running rigging & all fittings. The Mirror Dinghy was the winning entry in a design competition sponsored by the London Daily Mirror Newspaper. Designed by Jack Holt & Barry Bucknell, the Mirror has become one of the world's most popular designs. Since its appearance at the London Boat Show of 1963, over 70, 000 have been constructed. This beautiful boat is now available as a 1:6 scale radio controlled model. The kit has been designed to be built in the same ' Stitch & Glue' construction as the real boat & ll wood pieces have been laser cut. The kit also

Includes:: a main & jib with bolt rope & jib hanks, a pre-cast ballast bulb, fibreglass tape & wire for stitching & a detailed instruction booklet. The model sails very realistically & is easily transported thanks to the removable keel & retracting gaff. Whether used as radio control or simply displayed as a master piece for your living room, you will be amazed with the results. Scale: 1:6 Length: 550mm (21.66") Beam: 239mm (9.4")
Height: (rigged) 1041mm (41") Model suitable for R/C. Manufacturer: Osbourne Model Kits Model: Mirror Dinghy (1:6 Scale)


...

A 1938 stepped hydroplane driven by Harold Wilson, & designed by Douglas van Patten for Gold Cup racing. Hull construction of plywood with mahogany deck & vac formed parts, the kit features laser cut components, genuine copper exhaust pipes, scale vinyl decals, display st&, motor mount (for 500-600 motors) & scale cockpit interior with cloth seats. Kit also

Includes:: the running pack which features motor to shaft coupler, thrust bearing, drive shaft, stuffing tube, prop, prop nut, rudder & mounting hardware. Scale: 1:12 Length: 648mm (25.5") Beam: 178mm (7") Model Suitable for R/C. Manufacturer: Osborn Model Kits Model: Model Kits Miss Canada III (1:12 Scale Inc Drive Kit) (OSB-2502)

...

Including many of the features of the 1:12 scale RC kit, this is a 1:24 scale static display model of the sleek stepped hydro. Scale: 1:24 Length: 311mm (12.25") Beam: 89mm (3.5") Static model not suitable for R/C. Manufacturer: Osbourne Model Kits Model: Miss Canada III (1:24 Scale) (OSB-2510) ...

Beautifully crafted 1:10 scale radio controlled model kit of Art Ashby's famous 266 class hydroplane. The model is made from 3mm (1/8") plywood frames & 0.8mm (1/32") plywood decking & also features a vac formed cowl. Designed to run on a. 05 or brushless motor system, this kit also

Includes:: the running pack which features rudder set, turn fin, drive shaft, stuffing tube, motor to shaft coupler, prop, prop nuts, strut, antenna mount & mounting hardware. Scale: 1:10 Length: 635mm (25") Beam: 280mm (11") Vinyl decals are not included Model Suitable for R/C. Manufacturer: Osbourne Model Kits Model: Miss Canadiana (1:10 Scale Inc Drive Kit) (OSB-2505)

...

1:12 Scale model of the 3 time Harmsworth Trophy winner; 1959, 1960 & 1961. Kit features laser cut components, all plywood construction, authentic scale decals, vac formed cowl & Rolls Royce Griffin engine. Kit also

Includes:: the running pack which features motor to shaft coupler, thrust bearing, drive shaft, stuffing tube, prop, prop nut, rudder, turn fin & mounting hardware. Scale: 1:12 Length: 788mm (31") Beam: 318mm (12.5") Model Suitable for R/C. Manufacturer: Osbourne Model Kits Model: Osborn Miss Supertest III (1:12 Scale Inc Drive Kit)

...