Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Plastikleen.
- Dampen a clean, soft, lint free cloth with Plasticprep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Plastic prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Interior Coat Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. Interior Coat available in 6 colours & 2 different sizes. 6 colours available: Black, Biscuit, Off White, Light Grey, Navy Blue, Red & White.



...

Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Plastikleen.
- Dampen a clean, soft, lint free cloth with Plasticprep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Plastic prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Interior Coat Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. Interior Coat available in 6 colours & 2 different sizes. 6 colours available: Black, Biscuit, Off White, Light Grey, Navy Blue, Red & White.



...

Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Plastikleen.
- Dampen a clean, soft, lint free cloth with Plasticprep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Plastic prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Interior Coat Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. Interior Coat available in 6 colours & 2 different sizes. 6 colours available: Black, Biscuit, Off White, Light Grey, Navy Blue, Red & White.



...

Remove dirt, grease & silicones from vinyl or leather surfaces with Interior clean. Paint or lacquer with Interior Prep. The unique coating actually penetrates the surface & changes the pigmentation. When finished the grain of vinyl or leather is intact, it does not crack or peel. Afterwards, leather can be fed with hide food & will retain its natural aroma. Preparation is simple:
- Clean the interior by removing dirt, grease & silicones with Plastikleen.
- Dampen a clean, soft, lint free cloth with Plasticprep & wipe over the surface to be treated to remove all traces of any other previously applied products which might impair the bonding of the liquid plastic. This should leave the surface slightly tacky. Do not touch the surface again at the stage as it may become contaminated again.
- If treating semi-rigid, polythene & polypropylene plastics it is essential to use Adhesionaid before applying Liquid Plastic. Allow Plastic prep to dry before spraying. Shake the can thoroughly & apply a thin coat of Adhesion aid. Allow Adhesionaid to dry (12 minutes at 20 degree C) before applying Liquid Plastic.
- Spray Interior Coat Liquid Plastic for permanent, colourfast & weatherproof transformation. Check a small test area first before applying. After 15 minutes test by placing sticky tape on applied area. Upon removal there should be no liquid Plastic on tape. Apply in mist coats only, allowing 5-10 minutes flash off time between coats. Depending on the original colour between 2 & 3 evenly applied coats should cover the substrate. Do no attempt to cover in one coat or apply in thick coats. Liquid Plastic can be handled after 10-15 minutes & fully cures in 16-20 hours depending on the ambient temperature & humidity. Heat will reduce the drying times. High humidity or damp conditions can lead to poor adhesion and/or a blooming effect. Interior Coat available in 6 colours & 2 different sizes. 6 colours available: Black, Biscuit, Off White, Light Grey, Navy Blue, Red & White.



...

These 90° internal bent nose circlip pliers are ideal for removing & installing the snap rings on hydraulic master cylinders on motorcycles. 90° internal bent nose circlip pliers. For removing & installing the snap rings on hydraulic master cylinders on motorcycles. Spring loaded action for ease of use. Length of jaws 53mm Moulded handles for easy comfortable use. ...

10 Brass, coil & distributor terminals with covers for rewiring plug leads. ...

Impact driver set for hand or air hammer use. Ideal for removing corroded or over tightened fasteners. 3/8"D Impact driver for hand or air hammer use. For the removal of corroded or over tightened fasteners. Contents: 1 x 19mm flexi head wrench, 1 x impact driver with adaptor disc attached, 1 x air hammer adaptor. Removes fasteners by hammer or vibration ...

This innovative, Impact stud extractor is fully adjustable & can be used with air tools or standard hand tools on 6-12mm studs. It will effectively work on & remove threaded, broken, rusted, stripped or smooth studs. Laser 3986
- Impact Stud Extractor 1/2" Drive. A Set of 2 pieces is also available (3/8" & 1/4" drives) See the How Do I Remove Broken Studs? article in the Technical Articles section
...

Expert Quality, 6 point sockets forged from chrome vanadium steel hardened, tempered & chemically blacked for corrosion protection. Hole for accessory spring loaded ball. For use with air, electric or manual impact wrenches. Contents: 17, 19, 21 & 27mm sockets. ...

Red Fibre washers to suit banjos, plugs, jets etc. in compartment box 600 pieces. Imperial & Metric Red Fibre Washers are available:
-
...