The hole punch & die heads produce perfectly round, burr free holes in up to 1.5mm (16g) steel & 2.5mm (12g) aluminium. When working along a panel edge just mark the pitch on your job then set the depth gauge on the hand punch up to 51mm (2-inch) deep, to produce lines of equidistant holes. This tool is perfect for auto body, aviation & general shop use. Kit contains seven punch & die sets
- 1/8", 3/16", 1/4", 5/16", 3/8", 7/16".
...

Assortment plastic box with 1000 plates pieces of split washers. Metric & Imperial Steel Spring Washers are available:
- Imperial
...

Use old fashioned insulating tape for the final touch. The black impregnated cloth tape gives that original finish. Bright plastic ends spoil the effect. Comes in a 3 metre roll. Tape is 25mm wide ...

Disposable, In-Line Desiccant Air Dryer A unique design that combines desiccant drying with built in dirt & oil aerosol filters. Reduces humidity in air delivered to spray guns. Effective with both HVLP & Conventional spray equipment Operates at a maximum of 200 PSI with a temperature of up to 150˚ F (66˚C) Install at end of air line supplying air tools. An economical alternative to expensive, wall-mounted desiccant drying systems. Manufactured in USA ...

Check for Ignition Problems Attach between HT lead & Spark Plug & see the bulb flash each time it fires. Check consistency from idle up. ...

Protect your brass & copper pipes & fittings from tarnishing for years. This long lasting, rapid drying, film is suitable for interior or external use on any non-ferrous metal. Used by the MOD for shell cases. Film can be removed with cellulose thinners. Useable up to 100*C. Use the aerosol on larger areas, brush from the tin on smaller applications. Only use from the tin in temperatures below 25 deg. C otherwise the product will thicken too quiclkly & be difficult to paint.   ...

Protect your brass & copper pipes & fittings from tarnishing for years. This long lasting, rapid drying, film is suitable for interior or external use on any non-ferrous metal. Used by the MOD for shell cases. Film can be removed with cellulose thinners. Useable up to 100*C. Use the aerosol on larger areas, brush from the tin on smaller applications. Only use from the tin in temperatures below 25 deg. C otherwise the product will thicken too quiclkly & be difficult to paint. ...

New Safety Tread Spillage Absorbent is a Diatomaceous earth based product that is ultra absorbent & chemically inert. Fast absorbency properties make it ideal for soaking up oils, coolants, solvents, water, acids & caustics. The product retains it's granular appearance even when saturated & is fire retardant make it ideal to be used with low flash point solvents. Once used the product can be easily swept up. Product Benefits: High absorbency Fast acting Fire retardant Absorbency: Up to 15 litres of liquid per bag. When used for lubricants & diesel fuel this is reduced to 12 litres max per bag. ...

Soft interface pad for use with hook & loop backing pads. Using this interface between the pad & the disc gives the operator greater ability to sand the contours of the panel. Size 150mm X 20mm. 15 holes to match the backing pads.   ...

Miniature butt-weld clamps align panels edge-to-edge & surface-to-surface with the appropriate 0.040" gap that helps you produce clean welds with minimal grinding. A real boon to restorers. Ideal when welding patch repairs in floors, wings, door skins etc. or when assembling fabricated panels on reskinning projects. Intergrips will clamp flat, curved or even pressed ribbed panels. These little clamps will hold any shape panel in place anywhere
- edge to edge & perfectly prior to butt welding, leaving only a small gap which will allow full penetration of the weld. Once the two sections are tack welded together, the wing nut is slackened, the toggle bar removed & the clamp lifted from the job prior to final welding. The end result is a first class welded butt joint with very little dressing being necessary.
...