Using our combination kit, you can start with a rough casting & end with a mirror finish. Everything needed is included, except you & the drill. Kit contains 24 pieces & instructions. Pre-polish & finish Aluminum Alloys, Brass, Copper, Steel, Iron & Stainless Steel! The Polishing & Abrasive Kit contains :
- 3 of 4" x 1"  stitch mops
- 450g Tube 80 coarse grit abrasive compound
- 450g Tube 150 or 180 medium grit abrasive compound
- 450g Tube 240 or 300 fine grit abrasive compound
- 4" x 1"  Sisal mop
- 4" x 1"  White stitch mop
- 4" x 1"  G quality mop
- 100g Bar Grey compound
- 100g Bar Green compound
- 100g Bar Blue finishing compound
- Vienna Lime Powder
- 7 Small Polishing Felts
- 1 pair of gloves
- Steel Arbor
- Mini Arbor
- Dust Mask   Grades Available -  There are several grades of abrasive compound available. The lower the grit number, the coarser the abrasive & the faster metal removal (giving a poorer finish). The higher the grit number, the finer the abrasive & the slower the metal removal but it provides a better finish. To take a metal from a poor condition to a finish ready to be polished, will take several greaseless compound processes. For example, you can start at a wheel coated with 120 grit greaseless, next 180 grit & finally the wheel coated with 240 grit.















...

Heavy-Duty Slide Hammer grips studs so you can pull them out without slipping. Built for heavy-duty use, with a twist-on/twist-off chuck that grips dent-pulling pins/studs securely, without slipping. Pull pins without slipping Fits 2.0 & 2.5mm draw pins 20" long; weighs 10 lbs. Twist-on twist-off slide hammer is the same slide hammer included with our Deluxe Stud Welder (31123). Faster & easier to use than cheaper slide hammers, & less likely to push the dent back in. Made in the USA. ...

The swage has a substantial frame with an 18" throat & can accommodate mild steel sheet up to 1.2mm thick. The Bead Roller



...

This sturdy tubing roller lets you make smooth bends in steel, copper or aluminium tubing. It's great for bending exhaust pipes, water pipes, electrical conduit & tubing for chassis & roll cage fabrication. The tubing roller is equipped with three sets of rollers to handle tubing from 3/4" to 2" in diameter. Top screw allows for incremental bending for precise control to achieve the exact desired curve. This versatile tube bender reduces the risk of kinking & is essential for doing any tubing work.

Features:
- Incrementally creates the bend for precise control
- Bends tubing from 19mm (3/4") to 50.8mm (2") diameter
- Roller diameter: 100mm (4")
- Weight: 50kg  





...

Our range of Dollies are of the highest quality. They suit just about any application. Remember
- when quality counts, you get
...

Assortment of 30 plugs of various sizes used to plug bolt holes & support pieces in the oven during curing. The 30 piece assortment of tapered plugs are about an inch long & fit from 1/8" to 3/4" diameter holes. ...

For leveling or filling jobs that withstand up to 1000 degrees F, you need High-Temperature Lab Metal. Permanent repair compound, it is ready-to-use right from the can. Developed for difficult repairs subject to excessive heat, even in high-temperature applications, you can make permanent, rustproof, metal repairs with Hi-Temp Lab Metal. Thin with Lab Solvent to ease spreadability. Typically dries in 24 hours, heat cure at 425 deg F for 1 hour before exposing to high temperatures. Great for filling surfaces before powder coating where 2 or more coats are required. No messy mixing or measuring Creates a durable, heat-resistant, rustproof repair Can be machined, ground, filed & sanded Paint or powder-coat afterwards Easy to Use Hi-Temp Lab-metal is applied directly from the can with a putty knife or similar tool. No two-component mixing or measuring is necessary. Many applications may be made from a single can. After each use, to prevent Hi-Temp Lab-metal from hardening in the can, pour Lab-solvent over the remaining Hi-Temp Lab-metal contents, then cover tightly. (Stir the solvent into the Hi-Temp Lab-metal before using again). Lab-solvent is also used to thin Hi-Temp Lab-metal for brush-on applications. Durability Hi-Temp Lab-metal adheres to most metals. Once hardened, it can be machined, ground, filed, & sanded. Buffed to a satin smooth finish, Hi-Temp Lab-metal leaves an undetectable repair. Hi-Temp Lab-metal is impervious to the attack of rust, rot, & mildew. It is not affected by varying climatic conditions, & the hardened metal can be painted over -- even powder-coated. Preparation Please be aware that upon opening the tin the product will have settled & the resin will be sitting atop of the filler paste. The product will require breaking up & stirring for 10-15 minutes until a smooth even paste is achieved. Hi-Temp Lab-metal must be stirred thoroughly before use. No additive is needed; the repair compound hardens upon exposure to air. Hi-Temp Lab-metal is a viscous but easily spreadable paste. Upon opening the can, if the Hi-Temp Lab-metal appears stiff, stir in a capful or two of Lab-solvent to restore the product to its appropriate consistency. For any application, the surface must be clean & dry; free of paint, oil, dirt, & any extraneous materials. Roughening the surface provides superior adhesion. Hi-Temp Lab-metal's shelf life is one year in factory-sealed cans. Store in a cool place. See MSDS for safe handling. Application Hi-Temp Lab-metal may be applied with a putty knife, spatula, trowel, caulking gun, or rubber squeegee. When filling deep holes or cavities, the putty should be applied in thin layers, less than 1/4" thick. Allow each layer to dry for at least 24 hours. Dry time may be accelerated with force curing, infrared lamps. This depends on air temp, type of metal. To apply Hi-Temp Lab-metal with a paint brush, it must be thinned to paint consistency with Lab-solvent, then applied with light brush strokes; not worked over as with paint. Dipping the brush into Lab-solvent periodically will keep the bristles free & prevent clogging. Depth of application determines drying time; hardening occurs as the diluent evaporates. The application must air dry for at least 24 hours, or until the product has hardened to a metal state. In order for Hi-Temp Lab-metal to completly harden after a 24 hour air dry time, it must be exposed to a minimum temperature of 425ºF for a period of at least one hour depending on thickness of application. (The curing process may be achieved by a more gradual "heat-up", as in the repair of an industrial oven or exhaust. In this case, as the oven is heating, the Hi-Temp Lab-metal repair is curing.) Hi-Temp Lab-metal is recommended where original Lab-metal may not withstand the extreme heat. Originally developed due to requests from the foundry industry, industries such as metalworking, powder coating, welding, fabricating, heating, construction, auto repair, die casting, mold refinishing, & sheet metal production & finishing have found uses for Hi-Temp Lab-metal. It successfully repairs: Suggested Uses foundry core boxes duct work radiators mufflers, exhaust systems, engines molds wood & coal burning stoves, grills, industrial ovens dented metal, prior to powder-coating -- when Lab-metal cannot be used due to the extreme temperatures. ...

A specialised competition grease based on lithium soap & 20% molybdenum disulphide. Use as received, ideal for constant velocity joints & highly loaded sliding spline drive shafts. User Benefits: Very high molybdenum content versus normal black greases Proven in competition over many seasons Ideal for highly loaded constant velocity (CV) joints in motorsport applications Eliminates sliding spline binding under high acceleration loads The high molybdenum disulphide content provides a high load carrying capability making the product suitable for other high load applications Typical Characteristics: NGLI Grade: 2 Solids Content: 20% ...

These finest top quality brushes leave the competition standing, manufactured to the highest specifications. They are perfect for heavier cleaning jobs, removing paint, rust, scale, carbon & adhesive etc. They produce an excellent surface for painting or polishing Different size threads for use on SINGLE HAND GRINDERS. Read " How-To Strip Car Underside To Bare Metal " from our Technical Article for more useful tips. ...

These finest top quality brushes leave the competition standing, manufactured to the highest specifications. They are perfect for heavier cleaning jobs, removing paint, rust, scale, carbon & adhesive etc. They produce an excellent surface for painting or polishing Different size threads for use on SINGLE HAND GRINDERS. Read " How-To Strip Car Underside To Bare Metal " from our Technical Article for more useful tips. ...