Hotcoat Powder Coating (1 LB) for Hot Coat Powder Coating Gun. Powder coating means that you can coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black
- Orange
- Brown
- Yellow
- Green
- Bright Red
- Silver
- White
- Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021









...

From our large range of specialised aerosols comes this high quality silicone spray, which leaves trim surfaces gleaming. Trim Sheen is a fast economical way to reproduce an attractive & durable finish to dashboard, trims & all vinyl surfaces. ...

Steel tube is used for all kinds of fabrication work (motorbike frames, racing car chassis, roll bars, welding trolleys, go-karts, etc.) but can be tricky when you want to make neat butt welded T-joints. Frost Pipe Notcher is designed for use with any h&-held drill or drill press. Uses standard hole saw blades (not included) up to 2 inch diameter.

Features:
- Compound angle adjustment up to 60 degrees
- Easy to read angle scales
- Join round & rectangular Tubes
- Holds up to 2" dia round tube or 2" x 2-1/2" rectangular tubes





...

Foaming Tyre Dressing washes away dirt & grime, dries leaving a beautifully prepared tyre, ready to show. Does not crack or peel. Will not harm wheels or trims. ...

Ultimate Screen Wash protects against bottle freezing & removes traffic film to give a smear-free sparkle to your windscreen. -15’C Protection. Made in Engl&. ...

Not designed to replace a conventional high amperage charger unit, or to recharge from flat. 3 versions of Battery Savers are available:
-
...

Easy to use with excellent coverage, Frost Chassis Very Light Grey Primer is a fast drying acrylic paint designed for use on a range of metals prior to top coating. For years, vehicle builders & restorers have relied on the quality & strength of Frost Chassis paint range to protect suspension, steering, axles & all other under body components that risk damage in every day use. Our  Frost Chassis White Primer is oil resistant with 1 litre covering approx. 12 square metres ...

Ideal for all plastic, leather & vinyl surfaces Removes dirt, grease & silicones. Do not apply to cloth or nylon upholstery Apply with soft brush & rub firmly Wipe soapy residue with damp cloth & dry with soft cloth ...

Vinylprep is a solvent based cleaner for use on soft vinyl before applying Liquid Plastic. Vinylprep removes contaminants including polishes & lacquers. The substrate should be cleaned using Vinylprep on a clean white cloth. As you clean, the cloth should be turned so that a clean area of the cloth is always being used. The vinyl may feel a little tacky after cleaning with. This will help with the adhesion of the paint. For Professional Use Only. ...

Once corrosion starts between spot welded seams, it is difficult to stop it without removing & reassembling panels. You can ensure that it doesn’t start though, by coating the panel edges with our Zinc Rich Primer prior to assembly & spot welding. The high zinc content of our coating prevents corrosion & ensures good electrical conductivity for welding. Low cost insurance against future rust. 500 ml aerosol. See more Frost Aerosols below. ...