Hotcoat Powder Coating (1 kilo) for Hot Coat Powder Coating Gun. Powder coating means that you can coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black
- Orange
- Brown
- Yellow
- Green
- Bright Red
- Silver
- White
- Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021









...

Corrosion caused by moisture creeping into the small gaps between spot welded panels is one of the most common problems encountered on older vehicles. Using our Weld-thru Zinc Rich Primer prior to assembly will help combat this, but for assembled panels you can only hope to seal out moisture with a good quality seam sealer applied over the joint with a brush or spatula.
- Will not sag & is touch dry in hours
- Brushable Seam Sealer can be painted over in 2 to 3 hours.

...

Frost Bumper Black
- PCBLK1 Apply 3
- 4 coats • Allow 5mins to flash off between coats Carry out test spray Through cure 60mins

...

Frost Chassis Clean is an aggressive water based cleaner, ideal to be used with a pressure washer for cleaning grease, road film etc from chassis, engine bay, & other oily components. Can also be used concentrated with a stipple brush for local cleaning. ...

Protect your chassis with the classic finish. For years, vehicle builders & restorers have relied on the quality & strength of Frost Chassis Black Paint to protect suspension, steering, axles & all other under body components that risk damage in every day use. Our Chassis Black Paint is oil resistant with 1 litre covering approx. 12 square metres. Apply to a clean dry surface with a primer if applying to new or bare metal. It can be brushed on or sprayed, if thinned. If you require it to be thinned, we would recommend white spirit, max 10%
- 15%. The Frost Chassis Black is a protective one-pack coating for use in tough demanding conditions. This quick drying synthetic enamel is designed to provide a gloss finish with durability without sacrificing economy. It is suitable for the full range of commercial vehicle chassis including buses, trucks & trailers. It has a positive drying gives tack free time of 3 hours with the finish consisting of being a gloss finish that has excellent opacity.
...

Protect your chassis with the classic finish. For years, vehicle builders & restorers have relied on the quality & strength of Frost Chassis Black Paint to protect suspension, steering, axles & all other under body components that risk damage in every day use. Our Chassis Black Paint is oil resistant with 1 litre covering approx. 12 square metres. Apply to a clean dry surface with a primer if applying to new or bare metal. It can be brushed on or sprayed, if thinned. If you require it to be thinned, we would recommend white spirit, max 10%
- 15%. The Frost Chassis Black is a protective one-pack coating for use in tough demanding conditions. This quick drying synthetic enamel is designed to provide a satin finish with durability without sacrificing economy. It is suitable for the full range of commercial vehicle chassis including buses, trucks & trailers. It has a positive drying gives tack free time of 3 hours with the finish consisting of being a satin finish that has excellent opacity.
...

Hotcoat Powder Coating (1 LB)  for  Hot Coat Powder Coating Gun. Powder coating  allows you to coat & cure metal parts in less than an hour, & provides an extremely durable finish that is dent & chip resistant. It’s far superior to liquid coatings, it’s easy to apply with no drips or overspray, & contains no environmentally harmful solvents. Also available: Eastwood Hot Coat Powder Coating Colour Sample Kit Eastwood Extreme Chrome Bonded Hotcoat Powder Coating (8oz) 3 Steps: Strip & Clean your metal part before coating Coat the entire part – you can’t overcoat Cure your part in an electrical oven for about 20 minutes

Features: • Professional results • Quick colour changes • Durable finish • Easy set-up, easy to use, & easy to clean-up • Excellent fluidization of powders • Economical Get professional results with this innovative powder coating system at home. It is much more durable than coating with paint & does not flake when hit or bent. Depressing the activation switch energizes the Powdercoat gun, charging the powder. Move the gun in slightly different angles to ensure that all areas of the part are covered. The coated surface will have a dull opaque coating. Make sure all areas of the part are coated evenly. Place in the oven & bake for 15 minutes. Easy set-up, easy to use, & easy to clean. All you need is a compressed air source (5-10 PSI from a portable tank with a regulator or a compressor), mains electric supply & a dedicated electric oven. Colours Available: Blue- Jet Black – Orange – Brown – Yellow – Green – Bright Red – Silver – White – Graphite Black (NOTE: Exact colours are difficult to show, due to display settings) RAL Numbers: Blue-5012, Bright Red-3001, Brown-8011, Graphite Black-9011, Green-6018, Jet Black- 9005, Orange-2009, Silver 9006, White 9016, Yellow 1021    

...

Product

Features: OEM  finish on plastic bumper repair/plastic trim repair Coarse texture/fine texture from

...

Compact Floor Mounted Metal Bender Package Dimensions: 92cm x 28cm x 27cm Net Weight 24kgs Gross Weight 26kgs ...

The Complete Shrinker Stretcher with Foot Operated Stand can be used to fabricate or repair metal work around wheel arches, door edges, window frames, rain channels...almost any metal fabrication requiring a combination curve & angle especially those awkward areas around headlights. Use the shrinker to contract metal for inside curves: use the stretcher to expand metal for outside curves. The Complete Shrinker / Stretcher Stand Set,

Includes:: two separate pedal driven shaping units, one to stretch & one to shrink, mounted on the st&, along with two handy castors for free movement around the workshop. The Frost stretching/ shrinking machine is a clamping device which, under the influence of the lever, will squeeze whichever jaws are mounted in it. The jaws can be swapped for different jobs. A bespoke stand is available, but it’s easy enough to bolt the machine body to a bench or simply to hold it in a vice. Fully Assembled Dimensions:

Height: 110cm

Width: 125cm

Depth: 56cm Read " How Do I Use the Shrinking / Stretching Machine? " & " 10 MUST-HAVE Restoration Tools " from Technical Article. * Colour might be different from the picture.*







...